Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
It originally comes from the OpenWrt patches.
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch renames it for 3 reasons:
- "CONFIG" pattern is used by Kconfig. Now this macro is
no more defined by Kconfig but by Kbuild itself make this
clear by translating "CONFIG" into "KBUILD".
- "ELF32" word is improper because it is irrelevant to ELF
format and it makes confusion with CONFIG_BOOT_ELF32. So
translate it with SYM32.
- Add "64BIT" part to make clear that this macro implies a
64 bits kernel.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We do not rely on user anymore to setup this config correctly.
Instead we make our choice depending on the load address.
If we want to force Kbuild to use ELF64 format whatever
the load address we can still do:
$ make BUILD_ELF32=no
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They contain 64-bit instructions so wouldn't work on 32-bit kernels or
32-bit hardware. Since there are no users, blow them away. They
probably were only ever created because there are atomic_sub_if_positive
and atomic_dec_if_positive which exist only for sake of semaphores.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A "cleanup" almost two years ago deleted the old definition from
<asm/fcntl.h>, so asm-generic/fcntl.h defaulted it to the the same
value as FASYNC ... which happened to be the wrong thing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __pa() for those did assume that all symbols have XKPHYS values and
the math fails for any other address range.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a workaround to address warnings generated on the "n" constraint by
GCC 3.3 and below.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Revert b543858209 and add
no_pci_devices() check to avoid crash due to early calling of
pci_get_class().
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Following a strict interpretation the empty definition of irq_enable_hazard
has always been a bug - but an intentional one because it didn't bite.
This has now changed, for uniprocessor kernels mm/slab.c:do_drain()
[...]
on_each_cpu(do_drain, cachep, 1, 1);
check_irq_on();
[...]
may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting
in a back-to-back hazard.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Same as all the others, just put in the constants for the existing kernel
code and termios2 structure
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/traps.o
arch/mips/kernel/traps.c: In function 'show_backtrace':
arch/mips/kernel/traps.c:110: warning: unused variable 'ra'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the generation of asm-offset.h to work these need to be evaulatable
by gcc as a constant expression. This issue did exist for a while but
didn't bite because they're only in asm-offset.h for debugging purposes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove unused TIF_NOTIFY_RESUME flag for all processor architectures. The
flag was not used excecpt on IA-64 where the patch replaces it with
TIF_PERFMON_WORK.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EDAC has a foundation to perform software memory scrubbing, but it requires a
per architecture (atomic_scrub) function for performing an atomic update
operation. Under X86, this is done with a
lock: add [addr],0
in the file asm-x86/edac.h
This patch provides the MIPS arch with that atomic function, atomic_scrub() in
asm-mips/edac.h
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since Ingo's recent scheduler rewrite which was merged as commit
0437e109e1 sched_cacheflush is unused.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
New arch macro STACK_TOP_MAX it gives the larges valid stack address for the
architecture in question.
It differs from STACK_TOP in that it will not distinguish between
personalities but will always return the largest possible address.
This is used to create the initial stack on execve, which we will move down to
the proper location once the binfmt code has figured out where that is.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ollie Wild <aaw@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a reimplementation of the zs driver for the serial subsystem. Any
resemblance to the old driver is purely coincidential. ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...
Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.
This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add function helper, fb_is_primary_device(). Given struct fb_info, it will
return a nonzero value if the device is the primary display.
Currently, only the i386 is supported where the function checks for the
IORESOURCE_ROM_SHADOW flag.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move arch-specific bits of fb_mmap() to their respective subdirectories
[bob.picco@hp.com: efi_range_is_wc is referenced but not declared]
[bunk@stusta.de: fix include/asm-m68k/fb.h]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One common problem with 32 bit system call and ioctl emulation is the
different alignment rules between i386 and 64 bit machines. A number of
drivers work around this by marking the compat structures as
'attribute((packed))', which is not the right solution because it breaks
all the non-x86 architectures that want to use the same compat code.
Hopefully, this patch improves the situation, it introduces two new types,
compat_u64 and compat_s64. These are defined on all architectures to have
the same size and alignment as the 32 bit version of u64 and s64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Vasily Tarasov <vtaras@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill pte_rdprotect(), pte_exprotect(), pte_mkread(), pte_mkexec(), pte_read(),
pte_exec(), and pte_user() except where arch-specific code is making use of
them.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cast to a __user pointer via "unsigned long" to get rid of this warning:
include2/asm/compat.h:135:10: warning: cast adds address space to expression (<asn:1>)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
The only pseudo-legitimate MIPS user of genrtc was a systems that doesn't
have an RTC in hardware at all. At this point faking one is a little
pointless ...
To support multiple TC microthreads acting as "CPUs" within a VPE,
VPE-wide interrupt mask bits must be specially manipulated during
interrupt handling. To support legacy drivers and interrupt controller
management code, SMTC has a "backstop" to track and if necessary restore
the interrupt mask. This has some performance impact on interrupt service
overhead. Disable it only if you know what you are doing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also include tlbdebug.h in dump_tlb.c and r3k_dump_tlb.c.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is an workaround for these sparse warnings:
include2/asm/mmu_context.h:172:2: warning: symbol 'flags' shadows an earlier one
include2/asm/mmu_context.h:133:16: originally declared here
include2/asm/mmu_context.h:232:2: warning: symbol 'flags' shadows an earlier one
include2/asm/mmu_context.h:203:16: originally declared here
include2/asm/mmu_context.h:277:3: warning: symbol 'flags' shadows an earlier one
include2/asm/mmu_context.h:250:16: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CKSEG1ADDR() returns unsigned int value on 32bit kernel. Cast it to
unsigned long to get rid of this warning:
include2/asm/io.h:215:12: warning: cast adds address space to expression (<asn:2>)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based on replies to a respective query, remove the pci_dac_dma_...() APIs
(except for pci_dac_dma_supported() on Alpha, where this function is used
in non-DAC PCI DMA code).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm not sure if this is going to fly, weak symbols work on the compilers I'm
using, but whether they work for all of the affected architectures I can't say.
I've cc'ed as many arch maintainers/lists as I could find.
But assuming they do, we can use a weak empty definition of
pcibios_add_platform_entries() to avoid having an empty definition on every
arch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the termios2 structure ready for enabling on most platforms. One or
two like Sparc are plain weird so have been left alone. Most can use the
same structure as ktermios for termios2 (ie the newer ioctl uses the
structure matching the current kernel structure)
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Ian Molton <spyro@f2s.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using another systems defines is a safe way to get your code broken by
accident when that system is removed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is an workaround for these sparse warnings:
linux/include/linux/calc64.h:25:17: warning: symbol '__quot' shadows an earlier one
linux/include/linux/calc64.h:25:17: originally declared here
linux/include/linux/calc64.h:25:17: warning: symbol '__mod' shadows an earlier one
linux/include/linux/calc64.h:25:17: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use rtc-rs5c348 and at25 spi protocol driver and spi_txx9 spi
controller driver instead of platform dependent codes.
This patch also removes dependencies to old RTC interfaces such as
rtc_mips_get_time, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add PCI support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add mips common support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add core platform support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Which will cut down the cost of RDHWR $29 which is used to obtain the
TLS pointer and so far being emulated in software down to a single cycle
operation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to break the code of people who think they are supposed to scribble
into the pci device structure - it's off limits.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current implementation of __pa() for 64-bits kernels with 32-bits
symbols is broken. In this configuration, we need 2 values for
PAGE_OFFSET, one in XKPHYS and the other in CKSEG0 space.
When the value in CKSEG0 space is used, it doesn't take into account
of PHYS_OFFSET. Even worse we can't redefine this value.
The patch restores CPHYSADDR() but in __pa()'s implementation because
it removes the need of 2 PAGE_OFFSET.
OTOH, CPHYSADDR() is quite bad when dealing with mapped kernels. So
this patch assumes there's no need to deal with such kernel in 64-bits
world.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For platforms that use PHYS_OFFSET and do not use a mapped kernel,
this patch automatically adds PHYS_OFFSET into PAGE_OFFSET.
Therefore there are no more needs for them to redefine PAGE_OFFSET.
For mapped kernel, they need to redefine PAGE_OFFSET anyways.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PAGE_OFFSET definition is now using CAC_BASE by default.
This patch also reorder some macros to make them appear
in the same order for both 32 and 64 bits configs.
It also makes use of const.h generic header file to
annotate constants.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Before this patch, when a platform needed to customize one constant in
spaces.h, they need to redefine all of them.
Now they can just redefine one constant and include the generic file
header at the end:
#include <asm/mach-generic/spaces.h>
This patch doesn't allow to redefine CAC_BASE, IO_BASE and UNCAC_BASE
for 32 bits platforms because there's no need to do so.
This will avoid some macro duplications. It's important specially if
we'll add complex macros.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 include/asm-mips/mach-ip32/spaces.h
No point in adding yet another #ifdef for Loongson since all this mask is
being used for is converting an XKPHYS address into a physical address
anyway. So replace all definitions by one with the highest architectural
possible value.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
"extern inline" will have different semantics with gcc 4.3, and
"static inline" is correct here.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This updates the DMA whitelist in MIPS specific au1xxx ide
driver to use NULL instead of "ALL" as the wildcard.
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The idle loop goes to sleep using the WAIT instruction if !need_resched().
This has is suffering from from a race condition that if if just after
need_resched has returned 0 an interrupt might set TIF_NEED_RESCHED but
we've just completed the test so go to sleep anyway. This would be
trivial to fix by just disabling interrupts during that sequence as in:
local_irq_disable();
if (!need_resched())
__asm__("wait");
local_irq_enable();
but the processor architecture leaves it undefined if a processor calling
WAIT with interrupts disabled will ever restart its pipeline and indeed
some processors have made use of the freedom provided by the architecture
definition. This has been resolved and the Config7.WII bit indicates that
the use of WAIT is safe on 24K, 24KE and 34K cores. It also is safe on
74K starting revision 2.1.0 so enable the use of WAIT with interrupts
disabled for 74K based on a c0_prid of at least that.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Older processors used to encode processor version and revision in two
4-bit bitfields, the 4K seems to simply count up and even newer MTI cores
have switched to use the 8-bits as 3:3:2 bitfield with the last field as
the patch number.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The RM7000 processors and the E9000 cores have a bug (though PMC-Sierra
opposes it being called that) where invalid instructions in the same
I-cache line worth of instructions being fetched may case spurious
exceptions.
The workaround for this was only enabled for E9000 cores; enable it also
for all RM7000-based platforms.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This marks the declaration of die() correctly, removing "control reaches
end of non-void function" warnings from non-void functions that die() at
the end.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some IP35 defines snuck into some IP32-specific code during the DMA re-write.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a sparse warning caused by 2c921d07f8c641e691b0dfd80a5cfe14c60ec489
include2/asm/bitops.h:313:23: warning: symbol 'res' shadows an earlier one
include2/asm/bitops.h:309:16: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For some platforms it's definitions may conflict. So that's the one-liner.
The rest is 10 square kilometers of collateral damage fixup this include
used to paper over.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And an attempt to tidy up the core/controller differences.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This must be the oldest bug that we have got. Leaving interrupts "as
they are" for the R3000 obviously means copying IEp to IEc. Since we have
got STATMASK now, I took this opportunity to mask the status register
"correctly" for the R3000 now too. Oh, and the R3000 hardly ever is
64-bit.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
sys_fadvise64() is not used on MIPS. The libc can implement
both posix_fadvise() and posix_fadvise64() using sys_fadvise64_64().
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Aside of being handy for debugging this has never been a particularly
good idea but is now getting in the way of dyntick / tickless kernels
and general cleanups.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (28 commits)
[MIPS] Rework cobalt_board_id
[MIPS] Use RTC_CMOS for Cobalt
[MIPS] Use platform_device for Cobalt UART
[MIPS] Separate Alchemy processor based boards config
[MIPS] Fix build error in atomic64_cmpxchg
[MIPS] Run checksyscalls for N32 and O32 ABI
[MIPS] tlbex: use __maybe_unused
[MIPS] excite: use __maybe_unused
[MIPS] Add extern cobalt_board_id
[MIPS] Remove unused CONFIG_TOSHIBA_BOARDS
[MIPS] Rename tb0229_defconfig to tb0219_defconfig
[MIPS] Update tb0229_defconfig; add CONFIG_GPIO_TB0219.
[MIPS] Add minimum defconfig for RBHMA4200
[MIPS] SB1: Build fix.
[MIPS] Drop __devinit tag from allocate_irqno() and free_irqno()
[MIPS] clocksource: use CLOCKSOURCE_MASK() macro
[MIPS] Remove LIMITED_DMA support
[MIPS] Remove Momenco Jaguar ATX support
[MIPS] Remove Momenco Ocelot G support
[MIPS] FPU hazard handling
...
These files are almost all the same.
This patch could be made even simpler if we don't mind POLLREMOVE turning
up in a few architectures that didn't have it previously (which should be
OK as POLLREMOVE is not used anywhere in the current tree).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has some hackish code and it odd DMA results in the need to support
old features in kernel code.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move FPU hazard handling to hazards.h and provide proper support for
MIPSR2 processors
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
sound: convert "sound" subdirectory to UTF-8
MAINTAINERS: Add cxacru website/mailing list
include files: convert "include" subdirectory to UTF-8
general: convert "kernel" subdirectory to UTF-8
documentation: convert the Documentation directory to UTF-8
Convert the toplevel files CREDITS and MAINTAINERS to UTF-8.
remove broken URLs from net drivers' output
Magic number prefix consistency change to Documentation/magic-number.txt
trivial: s/i_sem /i_mutex/
fix file specification in comments
drivers/base/platform.c: fix small typo in doc
misc doc and kconfig typos
Remove obsolete fat_cvf help text
Fix occurrences of "the the "
Fix minor typoes in kernel/module.c
Kconfig: Remove reference to external mqueue library
Kconfig: A couple of grammatical fixes in arch/i386/Kconfig
Correct comments in genrtc.c to refer to correct /proc file.
Fix more "deprecated" spellos.
Fix "deprecated" typoes.
...
Fix trivial comment conflict in kernel/relay.c.
Recently a few direct accesses to the thread_info in the task structure snuck
back, so this wraps them with the appropriate wrapper.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the misspellings of "propogate", "writting" and (oh, the shame
:-) "kenrel" in the source tree.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
tas() has no users, so get rid of it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atomic_add_unless as inline. Remove system.h atomic.h circular dependency.
I agree (with Andi Kleen) this typeof is not needed and more error
prone. All the original atomic.h code that uses cmpxchg (which includes
the atomic_add_unless) uses defines instead of inline functions,
probably to circumvent a circular dependency between system.h and
atomic.h on powerpc (which my patch addresses). Therefore, it makes
sense to use inline functions that will provide type checking.
atomic_add_unless as inline. Remove system.h atomic.h circular dependency.
Digging into the FRV architecture shows me that it is also affected by
such a circular dependency. Here is the diff applying this against the
rest of my atomic.h patches.
It applies over the atomic.h standardization patches.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is a driver for the Alchemy au1550 PSC (Programmable Serial
Controller) in SPI master mode.
It supports dma transfers using the Alchemy descriptor based dma controller
for 4-8 bits per word SPI transfers. For 9-24 bits per word transfers, pio
irq based mode is used to avoid setup of dma channels from scratch on each
number of bits per word change.
Tested with au1550; this may also work on other MIPS Alchemy cpus, like
au1200/au1210/au1250. Used extensively with SD card connected via SPI;
this handles 8.1MHz SPI clock transfers using dma without any problem (the
highest SPI clock freq possible with au1550 running on 324MHz).
The driver supports sharing of SPI bus by multiple devices. All features
of Alchemy SPI mode are supported (all SPI modes, msb/lsb first, bits per
word in 4-24 range).
As the SPI clock of the controller depends on main input clock that shall
be configured externally, platform data structure for au1550 SPI controller
driver contains mainclk_hz attribute to define the input clock rate. From
this value, dividers of the controller for SPI clock are set up for
required frequency.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Whitespace and section fixups. Remove partial workaround for platform
setup bug in dma_mask setup; it couldn't work with multiple controllers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most architectures defined three macros, MK_IOSPACE_PFN(), GET_IOSPACE()
and GET_PFN() in pgtable.h. However, the only callers of any of these
macros are in Sparc specific code, either in arch/sparc, arch/sparc64 or
drivers/sbus.
This patch removes the redundant macros from all architectures except
sparc and sparc64.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the size of the per-cpu region reserved to save crash notes is
set by the per-architecture value MAX_NOTE_BYTES. Which in turn is
currently set to 1024 on all supported architectures.
While testing ia64 I recently discovered that this value is in fact too
small. The particular setup I was using actually needs 1172 bytes. This
lead to very tedious failure mode where the tail of one elf note would
overwrite the head of another if they ended up being alocated sequentially
by kmalloc, which was often the case.
It seems to me that a far better approach is to caclculate the size that
the area needs to be. This patch does just that.
If a simpler stop-gap patch for ia64 to be squeezed into 2.6.21(.X) is
needed then this should be as easy as making MAX_NOTE_BYTES larger in
arch/asm-ia64/kexec.h. Perhaps 2048 would be a good choice. However, I
think that the approach in this patch is a much more robust idea.
Acked-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the die notifier handling to common code. Previous
various architectures had exactly the same code for it. Note that the new
code is compiled unconditionally, this should be understood as an appel to
the other architecture maintainer to implement support for it aswell (aka
sprinkling a notify_die or two in the proper place)
arm had a notifiy_die that did something totally different, I renamed it to
arm_notify_die as part of the patch and made it static to the file it's
declared and used at. avr32 used to pass slightly less information through
this interface and I brought it into line with the other architectures.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix vmalloc_sync_all bustage]
[bryan.wu@analog.com: fix vmalloc_sync_all in nommu]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most architectures' scatterlist.h use the type dma_addr_t, but omit to
include <asm/types.h> which defines it. This could lead to build failures,
so let's add the missing includes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add hooks to allow a paravirt implementation to track the lifetime of
an mm. Paravirtualization requires three hooks, but only two are
needed in common code. They are:
arch_dup_mmap, which is called when a new mmap is created at fork
arch_exit_mmap, which is called when the last process reference to an
mm is dropped, which typically happens on exit and exec.
The third hook is activate_mm, which is called from the arch-specific
activate_mm() macro/function, and so doesn't need stub versions for
other architectures. It's called when an mm is first used.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: linux-arch@vger.kernel.org
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
[Robert's original log message said this was a bug but it isn't, it's
just very old fashioned syntax that is not (no longer?) documented in the
gcc documentation. So for the sake of uniformity I'm applying his
patch but with a modified log message. -- Ralf]
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an update to the earlier patch for the sibyte headers, and superceeds
the previous patch. Changes were necessary to get the tbprof driver working
on the bcm1480.
Patch to update Sibyte header files to match master versions maintained
at Broadcom. This patch also corrects some whitespace problems, and
(hopefully) shouldn't introduce any new ones.
Signed-off-by: Mark Mason <mason@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that network timestamps use ktime_t infrastructure, we can add a new
SOL_SOCKET sockopt SO_TIMESTAMPNS.
This command is similar to SO_TIMESTAMP, but permits transmission of
a 'timespec struct' instead of a 'timeval struct' control message.
(nanosecond resolution instead of microsecond)
Control message is labelled SCM_TIMESTAMPNS instead of SCM_TIMESTAMP
A socket cannot mix SO_TIMESTAMP and SO_TIMESTAMPNS : the two modes are
mutually exclusive.
sock_recv_timestamp() became too big to be fully inlined so I added a
__sock_recv_timestamp() helper function.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: linux-arch@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Now network timestamps use ktime_t infrastructure, we can add a new
ioctl() SIOCGSTAMPNS command to get timestamps in 'struct timespec'.
User programs can thus access to nanosecond resolution.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the current version of the 64 bit divide common code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've traced down an off-by-one TCP checksum calculation error under
the following conditions:
1) The TCP code needs to split a full-sized packet due to a reduced
MSS (typically due to the addition of TCP options mid-stream like
SACK).
_AND_
2) The checksum of the 2nd fragment is larger than the checksum of the
original packet. After subtraction this results in a checksum for
the 1st fragment with bits 16..31 set to 1. (this is ok)
_AND_
3) The checksum of the 1st fragment's TCP header plus the previously
32bit checksum of the 1st fragment DOES NOT cause a 32bit overflow
when added together. This results in a checksum of the TCP header
plus TCP data that still has the upper 16 bits as 1's.
_THEN_
4) The TCP+data checksum is added to the checksum of the pseudo IP
header with csum_tcpudp_nofold() incorrectly (the bug).
The problem is the checksum of the TCP+data is passed to
csum_tcpudp_nofold() as an 32bit unsigned value, however the assembly
code acts on it as if it is a 64bit unsigned value.
This causes an incorrect 32->64bit extension if the sum has bit 31
set. The resulting checksum is off by one.
This problems is data and TCP header dependent due to #2 and #3
above so it doesn't occur on every TCP packet split.
Signed-off-by: Dave Johnson <djohnson+linux-mips@sw.starentnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With commit 63dc68a8cf, kernel can not
handle BUG() and BUG_ON() properly since get_user() returns false for
kernel code. Use __get_user() to skip unnecessary access_ok(). This
patch also make BRK_BUG code encoded in the TNE instruction.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The save_fp_context()/restore_fp_context() might sleep on accessing
user stack and therefore might lose FPU ownership in middle of them.
If these function failed due to "in_atomic" test in do_page_fault,
touch the sigcontext area in non-atomic context and retry these
save/restore operation.
This is a replacement of a (broken) fix which was titled "Allow CpU
exception in kernel partially".
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The commit 4d40bff7110e9e1a97ff8c01bdd6350e9867cc10 ("Allow CpU
exception in kernel partially") was broken. The commit was to fix
theoretical problem but broke usual case. Revert it for now.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent versions of the BCM112X processors aren't recognized by Linux
(preventing Linux from booting on those processors). This patch adds
support for those that are missing.
Signed-off-by: Mark Mason <mason@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
local_irq_restore -> raw_local_irq_restore -> irq_restore_epilog ->
smtc_ipi_replay -> smtc_ipi_dq -> spin_unlock_irqrestore ->
_spin_unlock_irqrestore -> local_irq_restore
The recursion does abort when there is no more IPI queued for a CPU, so
this isn't usually fatal which is why we got away with this for so long
until this was discovered by code inspection.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The missing cast did result a warning when calling an 32-bit ARC firmware
function that takes 5 arguments where the 5th argument is a pointer from a
64-bit kernel.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the the sequence:
ei
..
mfc0 $x, $status
the mfc0 may not see the SR_IE bit set. This was a deliberate bug in the
kernel code because we knew this was a safe thing to do on all R2 silicon
so far but new silicon is changing this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes two places where we used plain 'x - PAGE_OFFSET' to
achieve virtual to physical address convertions. This type of convertion
is no more allowed since commit 6f284a2ce7.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
[Build fixes for machines that don't use the generic dma-coherence.h]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the static prototypes from the au1xxx_ide.h, some of
them were not even implemented. Also, they caused build breakage since
they differed from the functions actually implemented in
drivers/ide/mips/au1xxx-ide.c.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
include/asm-mips/mach-ip27/dma-coherence.h:22: warning: 'plat_map_dma_mem' defined but not used
include/asm-mips/mach-ip27/dma-coherence.h:41: warning: 'plat_unmap_dma_mem' defined but not used
include/asm-mips/mach-ip32/dma-coherence.h:30: warning: 'plat_map_dma_mem' defined but not used
include/asm-mips/mach-ip32/dma-coherence.h:63: warning: 'plat_unmap_dma_mem' defined but not used
These functions are meant to be inlined anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Fix build error.
o Handle error returns.
o Deal with signals received while sleeping.
o Don't allow to be selected when we're not building the directory with
the driver anyway.
o Coding style cleanups.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A deadlock can occur for mixed irq and non-irq rwlock readers if a 2nd
reader attempts to take lock by looping around __raw_read_trylock().
Signed-off-by: Dave Johnson <djohnson+linux-mips@sw.starentnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the SMT-nice feature which idles sibling cpus on SMT cpus to
facilitiate nice working properly where cpu power is shared. The idling of
cpus in the presence of runnable tasks is considered too fragile, easy to
break with outside code, and the complexity of managing this system if an
architecture comes along with many logical cores sharing cpu power will be
unworkable.
Remove the associated per_cpu_gain variable in sched_domains used only by
this code.
Also:
The reason is that with dynticks enabled, this code breaks without yet
further tweaks so dynticks brought on the rapid demise of this code. So
either we tweak this code or kill it off entirely. It was Ingo's preference
to kill it off. Either way this needs to happen for 2.6.21 since dynticks
has gone in.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick). This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Big endian RMs uses a different mc146818_decode_year than little endian RMs
Correct mc146818_decode_year for years before 2000
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Delete the definition of the apparently unreferenced macro _IOC_SLMASK.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use MIPS_CPU_IRQ_BASE instead of own define.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds trivial support for SMARTMIPS extension. This extension
is currently implemented by 4KS[CD] CPUs.
Basically it saves/restores ACX register, which is part of the SMARTMIPS
ASE, when needed. This patch does *not* add any support for Smartmips MMU
features.
Futhermore this patch does not add explicit support for 4KS[CD] CPUs since
they are respectively mips32 and mips32r2 compliant. So with the current
processor configuration, a platform that has such CPUs needs to select
both configs:
CPU_HAS_SMARTMIPS
SYS_HAS_CPU_MIPS32_R[12]
This is due to the processor configuration which is mixing up all the
architecture variants and the processor types.
The drawback of this, is that we currently pass '-march=mips32' option to
gcc when building a kernel instead of '-march=4ksc' for 4KSC case. This
can lead to a kernel image a little bit bigger than required.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
From the 01408c4939 log message:
The problem is that when we write to a file, the copy from userspace to
pagecache is first done with preemption disabled, so if the source
address is not immediately available the copy fails *and* *zeros* *the*
*destination*.
This is a problem because a concurrent read (which admittedly is an odd
thing to do) might see zeros rather that was there before the write, or
what was there after, or some mixture of the two (any of these being a
reasonable thing to see).
If the copy did fail, it will immediately be retried with preemption
re-enabled so any transient problem with accessing the source won't
cause an error.
The first copying does not need to zero any uncopied bytes, and doing
so causes the problem. It uses copy_from_user_atomic rather than
copy_from_user so the simple expedient is to change copy_from_user_atomic
to *not* zero out bytes on failure.
< --- end cite --- >
This patch finally implements at least a not so pretty solution by
duplicating the relevant part of __copy_user.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel use 64-bit for sc_regs[0], and both N32/N64 userland
expects it was 64-bit. But size of 'long' on N32 is actually 32-bit.
So this definition make some confusion. Use __u32 and __u64 for
N32/N64 sigcontext to get rid of this confusion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes some sparse warnings.
pgtable-32.c:15:6: warning: symbol 'pgd_init' was not declared. Should it be static?
pgtable-32.c:32:13: warning: symbol 'pagetable_init' was not declared. Should it be static?
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add R2 optimized variants of clear_bit, set_bit and test_and_clear_bit.
With gcc 4.1.1 this saves 1592 bytes on a defconfig (minus IPv6) kernel.
Turns out that R2 bitop instructions are no gain for the other bitop
functions.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This implementation has support for the concept of one separate ioport
address space by PCI domain. A pointer to the virtual address where
the port space of a domain has been mapped has been added to struct
pci_controller and systems should be fixed to fill in this value. For
single domain systems this will be the same value as passed to
set_io_port_base().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
access_ok in compat-signal.h is wrong (checking destination instead of
source) and redundant (already checked before calling this function).
Also sf_mask in struct sigframe32 should be compat_sigset_t type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This did result in double clearing of the error return value on success
only but should make a meassurable overhead for sigreturn.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Platforms will now have to supply a function dma_device_is_coherent which
returns if a particular device participates in the coherence domain. For
most platforms this function will always return 0 or 1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that finally all supported versions of binutils have functioning
support for .subsection use .subsection to tweak the branch prediction
I did not modify the R10000 errata variants because it seems unclear if
this will invalidate the workaround which actually relies on the cheesy
prediction of branch likely to cause a misspredict if the sc was
successful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] signal: do not inline handle_signal()
[MIPS] signal: do not use save_static_function() anymore
[MIPS] signal32: no need to save c0_status register in setup_sigcontext32()
[MIPS] signal32: reduce {setup,restore}_sigcontext32 sizes
[MIPS] signal: factorize debug code
[MIPS] signal: test return value of install_sigtramp()
[MIPS] signal32: remove duplicate code
[MIPS] signal: clean up sigframe structure
[MIPS] signal: do not inline functions in signal-common.h
[MIPS] signals: reduce {setup,restore}_sigcontext sizes
[MIPS] Fix warning in get_user when fetching pointer object from userspace.
[MIPS] Fix eth2 platform device id for jaguar_atx and ocelot_3 platforms
[MIPS] JMR3927 and RBTX49x7 support little endian
[MIPS] RBTX49x7: declare prom_getcmdline()
[MIPS] RTLX: Sprinkle device model code into code to make udev happier.
[MIPS] VPE: Sprinkle device model code into code to make udev happier.
The line discipline numbers N_* are currently defined for each architecture
individually, but (except for a seeming mistake) identically, in
asm/termios.h. There is no obvious reason why these numbers should be
architecture specific, nor any apparent relationship with the termios
structure. The total number of these, NR_LDISCS, is defined in linux/tty.h
anyway. So I propose the following patch which moves the definitions of
the individual line disciplines to linux/tty.h too.
Three of these numbers (N_MASC, N_PROFIBUS_FDL, and N_SMSBLOCK) are unused
in the current kernel, but the patch still keeps the complete set in case
there are plans to use them yet.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the last vestiges of the long-deprecated "MAP_ANON" page protection
flag: use "MAP_ANONYMOUS" instead.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All the information in the MIPS c0_status register is priviledged.
Nothing that would constitute part of the thread context.
The one flag one could possibly argument about might be c0_status.fr
but none of the ABIs or tools or application software can make use
of it.
So for consistency with restore_sigcontext32(), which does not
restore c0_status register, this patch remove the saving part.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-apm:
[APM] SH: Convert to use shared APM emulation.
[APM] MIPS: Convert to use shared APM emulation.
[APM] ARM: Convert to use shared APM emulation.
[APM] Add shared version of APM emulation
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-tc:
[EISA] EISA registration with !CONFIG_EISA
[TC] pmagb-b-fb: Convert to the driver model
[TC] dec_esp: Driver model for the PMAZ-A
[TC] mips: pmag-ba-fb: Convert to the driver model
[TC] defxx: TURBOchannel support
[TC] TURBOchannel support for the DECstation
[TC] MIPS: TURBOchannel resources off-by-one fix
[TC] MIPS: TURBOchannel update to the driver model
On all targets that sucker boils down to memcpy_fromio(sbk->data, from, len).
The function name is highly misguiding (it _never_ does any checksums), the
last argument is just a noise and simply expanding the call to memcpy_fromio()
gives shorter and more readable source. For a lot of reasons it has almost
no remaining users, so it's better to just outright kill it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also convert to use generic kernel/power/Kconfig to make the use of the
shared APM emulation possible.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the platform-specific part of TURBOchannel bus support for the
DECstation. It implements determining whether the bus is actually there,
getting bus parameters, IRQ assignments for devices and protected accesses
to possibly unoccupied slots that may trigger bus error exceptions.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a set of changes to convert support for the TURBOchannel bus to the
driver model. It implements the usual set of calls similar to what other bus
drivers have: tc_register_driver(), tc_unregister_driver(), etc. All the
platform-specific bits have been removed and headers from asm-mips/dec/ have
been merged into linux/tc.h, which should be included by drivers.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The problem was introduced in 2.6.18.3 with the casting of some
36bit-defines (PCI memory) in au1000.h to resource_size_t which may be
u32 or u64 depending on the experimental CONFIG_RESOURCES_64BIT.
With unset CONFIG_RESOURCES_64BIT, the pci-memory cannot be accessed
because the ioremap in arch/mips/au1000/common/pci.c already used the
truncated addresses.
With set CONFIG_RESOURCES_64BIT, things get even worse, because PCI-scan
aborts, due to resource conflict: request_resource() in arch/mips/pci/pci.c
fails because the maximum iomem-address is 0xffffffff (32bit) but the
pci-memory-start-address is 0x440000000 (36bit).
To get pci working again, I propose the following patch:
1. remove the resource_size_t-casting from au1000.h again
2. make the casting in arch/mips/au1000/common/pci.c (it's allowed and
necessary here. The 36bit-handling will be done in __fixup_bigphys_addr).
With this patch pci works again like in 2.6.18.2, the gcc-compile warnings
in pci.c are gone and it doesn't depend on CONFIG_EXPERIMENTAL.
Signed-off-by: Alexander Bigga <ab@mycable.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/au1000/common/pci.o
arch/mips/au1000/common/pci.c:42: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:43: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:49: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:50: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c: In function ‘au1x_pci_setup’:
arch/mips/au1000/common/pci.c:82: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The old code was assuming that min_low_pfn was always 0. This
means that platforms having a big hole at their memory start
paid the price of wasting some memory for the allocation of
unused entries in mem_map[].
This patch prevents this waste.
It introduces PHYS_OFFSET define which is the start of the
physical memory and uses it wherever needed. Specially when
converting physical/virtual addresses into virtual/physical
ones.
Currently all platforms defines PHYS_OFFSET to 0.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes a better usage of these two globals.
'min_low_pfn' is now correctly setup for all configs, which
allow us to rely on it in boot memory code init.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current prom_free_prom_memory() implementations are almost same as
free_init_pages(), or no-op. Make free_init_pages() extern (again)
and make prom_free_prom_memory() use it.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move I8259A_IRQ_BASE from asm/i8259.h to asm/mach-generic/irq.h and
make it really customizable. And remove I8259_IRQ_BASE declared on
some platforms. Currently only NEC_CMBVR4133 is using custom
I8259A_IRQ_BASE value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq_base for {mips,rm7k,rm9k}_cpu_irq_init() are constant on all
platforms and are same value on most platforms (0 or 16, depends on
CONFIG_I8259). Define them in asm-mips/mach-generic/irq.h and make
them customizable. This will save a few cycle on each CPU interrupt.
A good side effect is removing some dependencies to MALTA in generic
SMTC code.
Although MIPS_CPU_IRQ_BASE is customizable, this patch changes irq
mappings on DDB5477, EMMA2RH and MIPS_SIM, since really customizing
them might cause some header dependency problem and there seems no
good reason to customize it. So currently only VR41XX is using custom
MIPS_CPU_IRQ_BASE value, which is 0 regardless of CONFIG_I8259.
Testing this patch on those platforms is greatly appreciated. Thank
you.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nick Piggin points out that page accounting on MIPS multiple ZERO_PAGEs
is not maintained by its move_pte, and could lead to freeing a ZERO_PAGE.
Instead of complicating that move_pte, just forget the minor optimization
when mremapping, and change the one thing which needed it for correctness
- filemap_xip use ZERO_PAGE(0) throughout instead of according to address.
[ "There is no block device driver one could use for XIP on mips
platforms" - Carsten Otte ]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 8e3d8433d8 ([NET]: MIPS
checksum annotations and cleanups) broke 64-bit MIPS.
The problem is the commit replaces some unsigned long with __be32. On
64bit MIPS, a __be32 (i.e. unsigned int) value is represented as a
sign-extented 32-bit value in a 64-bit argument register. So the
address 192.168.0.1 (0xc0a80001) is passed as 0xffffffffc0a80001 to
csum_tcpudp_nofold() but the asm code in the function expects
0x00000000c0a80001, therefore it returns a wrong checksum. Explicit
cast to unsigned long is needed to drop high 32bit.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
