This patch fixes the 16-bit case of the sh4a specific
unaligned access implementation. Without this patch
the 16-bit version of sh4a get_unaligned() results in
a 32-bit read which may read more data than intended
and/or cross page boundaries.
Unbreaks mtd NOR write handling on Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add shared code for 4-bit divisor clocks.
Processor specific code can use SH_CLK_DIV4()
to initialize div4 clocks, and then use
sh_clk_div4_register() for registration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add shared 32-bit module stop bit clock support.
Processor specific code can use SH_CLK_MSTP32()
to initialize module stop bit clocks, and then
use sh_clk_mstp32() for registration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7785 mode pin definitions. Mode pins and
pin function controller comments are added as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add mode pin support for the SuperH architecture V2.
With this patch applied the board code can add their
own function to export the cpu mode pin configuration.
In most cases this will be a constant bitmap, but
boards that allow reading this from a register can
instead read out the pin state from hardware.
The code warns if a pin is tested but no board specific
mode pin function has been provided.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The flat loader uses an architecture's flat_stack_align() to align the
stack but assumes word-alignment is enough for the data sections.
However, on the Xtensa S6000 we have registers up to 128bit width
which can be used from userspace and therefor need userspace stack and
data-section alignment of at least this size.
This patch drops flat_stack_align() and uses the same alignment that
is required for slab caches, ARCH_SLAB_MINALIGN, or wordsize if it's
not defined by the architecture.
It also fixes m32r which was obviously kaput, aligning an
uninitialized stack entry instead of the stack pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
None of the SH PCI controllers support MWI, it is always treated as a
direct memory write, so simply disable it outright. In the case of the
PCI cache line size, consult that for the pci_dma_burst_advice()
strategy, and switch over to PCI_DMA_BURST_MULTIPLE, as PPC64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the ->build_rate_table() callback,
->recalc() may instead be used for this purpose.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the ms7724se solution engine board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
hd64461 is mapped in a fixed location, so the I/O base itself is fairly
meaningless as a configuration item. Additionally, this makes it
impossible to share hd64461 code alongside generic drivers (in the case
of sh_dac_audio), so simply make it commonly defined and permit the
mach_is_foo() logic to work out the proper semantics.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in all of the MSTP functions in to the clock framework,
and hands them off to the platform devices that want them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adopts the OMAP clock framework debugfs bits and replaces the aging
procfs bits. The procfs clocks entry was primarily a debugging aid, and
used to be tied in to cpuinfo before the clock list grew too unweildly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for constructing a rate table by looking at potential
divisors for a specified clock. Each FQRMR clock is given its own table.
Presently each table is rebuilt when the parent propagates down a new
rate, so some more logic needs to be added to do this more intelligently.
Additionally, a fairly generic round_rate() implementation is then
layered on top of it, which subsequently provides us with cpufreq support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This updates the SH7785 CPU code as well as the SH7785LCR board support
code for making use of the newly refactored clock framework. Support for
the legacy CPG clocks is dropped at this point, with the extal frequency
fed in from the board code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves out the old legacy CPG clocks to their own file, and converts
over the existing users. With these clocks going away and each CPU
dealing with them on their own, CPUs can gradually move over to the new
interface.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now with all of the TMU users moved over to the new TMU driver, and the
old TMU driver killed off, the left-over infrastructure can go along
with it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old TMU driver (CONFIG_SH_TMU/timer-tmu.c)
As replacement, select the sh_tmu driver with CONFIG_SH_TIMER_TMU
and configure timer channel using platform data.
If multiple TMU channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_tmu.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This stubs in clk_get_sys() from the ARM clkdev implementation.
Tentatively conver the clk_get() lookup code to use this, and once the
rest of the in-tree users are happy with this, it can replace the
fallback lookups.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The only user for this is the SH-Mobile r_clk, which is now added as a
root clock and can be kicked via propagate_rate() as usual. Given that,
there is no longer any need for the special clk_recalc_rate(), so we kill
it off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This causes the generic clk_set_parent() implementation to be a bit more
intelligent. A clk_reparent() is added to move the clock over to the new
parent's sibling list, which then allows the generic rate propagation
code to succeed. This also becomes a nop if the new and old parents are
unchanged.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are a couple of instances where a clk_enable() can fail, which the
SH-Mobile code presently handles, but doesn't get reported all the way
back up. This fixes up the return type so the errors make it all the way
down to the drivers.
Additionally, we now also error out properly if the parent enable fails.
Prep work for aggressively turning off unused clocks on boot.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is no real distinction here in behaviour, either a clock needs to
be enabled on initialiation or not. The ALWAYS_ENABLED flag was always
intended to only apply to clocks that were physically always on and could
simply not be disabled at all from software. Unfortunately over time this
was abused and the meaning became a bit blurry.
So, we kill off both of all of those paths now, as well as the newer
NEEDS_INIT flag, and consolidate on a CLK_ENABLE_ON_INIT. Clocks that
need to be enabled on initialization can set this, and it will purposely
enable them and bump the refcount up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This resyncs the rate propagation strategy with the scheme used by the
OMAP clock framework. Child clocks are tracked on a list under each
parent and propagation happens there specifically rather than constantly
iterating over the global clock list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a followparent_recalc() helper for clocks that just follow the
parent's rate. Switch over the few CPUs that use this scheme for some of
their clocks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the broken I2C offset in 32-bit mode.
The cause is because the board datasheet had a mistake.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is nothing in these routines that inherently depends on R0 use.
Given that these routines are inlined, it is rather easy to blow up the
compiler by exhausting the spill class when performing a 64-bit swab.
This presently manifests itself as the following:
CC fs/ocfs2/suballoc.o
fs/ocfs2/suballoc.c: In function 'ocfs2_reserve_suballoc_bits':
fs/ocfs2/suballoc.c:638: error: unrecognizable insn:
(insn 2793 1230 1231 103 arch/sh/include/asm/swab.h:33 (set (reg:HI 853)
(subreg:HI (reg:SI 149 macl) 2)) -1 (expr_list:REG_DEAD (reg:SI 149 macl)
(nil)))
fs/ocfs2/suballoc.c:638: internal compiler error: in extract_insn, at recog.c:1991
This patch switches over to using an arbitrarily assigned register instead.
While the same issue does not exist in the SH-5 case, there is likewise no harm
in having an alternate register used for the byterev/shari pair.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These are presently only defined for sh32, use the plain unoptimized
versions for sh64. Fixes up smsc911x build.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the clock framework use count code.
With this patch the enable() and disable() callbacks
only get called when counting from and to zero.
While at it the kref stuff gets replaced with an int.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nothing is using this anymore now that we have fully converted to generic
time, so kill it off completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently shm_align_mask is only looked at for the bottom up case, but we
still want this for proper colouring constraints in the topdown case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the stragglers (MTU2/CMT/etc.) have been rewritten and we are
selecting both GENERIC_TIME and GENERIC_CLOCKEVENTS, the get_offset()
timer op is completely unused. As a result, we are now able to kill off
the ARCH_USES_GETTIMEOFFSET references.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old MTU2 driver (CONFIG_SH_MTU2/timer-mtu2.c)
As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_MTU2
and configure timer channel using platform data.
If multiple MTU channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_mtu2.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert sh to use GENERIC_TIME via the arch_getoffset() infrastructure.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old CMT driver (CONFIG_SH_CMT/timer-cmt.c)
As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_CMT
and configure timer channel using platform data.
If multiple CMT channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_cmt.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All 32-bit SuperH processors currently go through __ioremap_mode()
and check for IO_TRAPPED and directly mapped segments. With this
patch we simplify the MMU less case with a pass through version of
__ioremap_mode() which just returns the physical address.
The effects of this is change are:
- fix non-MMU ioremap() of high address hardware blocks (sh7203 CMT)
- make sure IO_TRAPPED is not selected
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
syscall_nr is presently defined as unsigned in the SH-5 pt_regs,
while the syscall restarting code wants it to be signed. Fix this
up, and bring it in line with the other SH parts.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves off of the board_pci_channels[] approach for bus registration
and over to a cleaner register_pci_controller(), all derived from the
MIPS code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all PCI channels have non-translatable memory windows, this is a
special property of the on-chip PCIC with its 0xfd00... mapping, handle
this explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the pci_iomap() definitions and reworks how the I/O
port base is handled. PCI channels can register their own I/O map base,
or if none is provided, the system-wide generic I/O base is used instead.
Functionally nothing changes, while this allows us to kill off lots of
I/O address special casing and lookups.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is left over cruft that hasn't been used by anything in a long time,
kill off bits that weren't purged previously.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This introduces a saner pcibios_align_resource() that can be used
regardless of whether pci-auto or pci-new are being used, and
consolidates it in pci-lib.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new PCI code wants its own bus<->resource mappings instead of the
generic equivalents, so drop the asm-generic include in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a plat_early_device_setup() function to allow
processor-specific code to register Early Platform Data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a __get_pci_io_base() function which is used to match a port range
against struct pci_channel. This allows us to detect if a port range is
assigned to pci or happens to be legacy port io. While at it, remove unused
cpu-specific cruft.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the code to use __is_pci_memory() instead of
is_pci_memaddr(). __is_pci_memory() loops through all the pci
channels on the system to match memory windows.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the io window base address in struct pci_channel and use that one
instead of SH77xx_PCI_IO_BASE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the base address of the pci host controller registers in struct
pci_channel and use the address in pci_read_reg() and pci_write_reg().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store a struct pci_channel pointer in bus->sysdata. This makes whatever
struct pci_channel assigned to a bus available for sh4_pci_read() and
sh4_pci_write(). We also modify PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM to
use bus->sysdata - this to gives us support for multiple pci channels.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an init callback to struct pci_channel and makes sure
it is initialized properly. Code is added to call this init function
from pcibios_init(). Return values are adjusted and a warning is is
printed if init fails.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH-Mobile R2R CPU.
Based on Rev 0.11 of the initial SH7724 hardware manual.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpuidle wants ARCH_HAS_DEFAULT_IDLE defined in order to use the
default idle loop. So, make it accessible and enable it for all
sh machines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the ifndef __ASSEMBLY__ preprocessor to allow the
defines in the file to be used also in assembly code.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Everyone defines it, and only one person uses it
(arch/mips/sgi-ip27/ip27-nmi.c). So just open code it there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-mips@linux-mips.org
Rework the hd64461 demuxer code to fix the HD64461 level-triggered
interrupts handling, using handle_level_irq() as needed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
http://marc.info/?t=123609820900002&r=1&w=2http://marc.info/?t=123660375800003&r=1&w=2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.
This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-3 does not support 'pref'-based prefetching, only SH-2A and SH-4A
parts do. Remove SH-3 from the list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework and simplify the sched_clock and clocksource code. Instead
of registering the clocksource in a shared file we move it into the
tmu driver. Also, add code to handle sched_clock in the case of no
clocksource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix macros start_thread and user_stack_pointer.
When these macros aren't called with a variable named regs as second
argument, this will result in a build failure.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that atomic_t is a generic opaque type for all architectures, it is
unwise to use intimate knowledge of its internals when manipulating it.
Instead of relying on the "counter" member being at offset 0 from the
beginning of an atomic_t, explicitly reference the member. This guards
us from any changes to the layout of the beginning of the atomic_t type.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When dereferencing the memory address contained in a register and
modifying the value at that memory address, the register should not be
listed in the inline asm outputs. The value at the memory address is an
output (which is taken care of with the "memory" clobber), not the register.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This corrects a deadlock encountered on ap325 in the cases where the
mutex is contended and the slow-path needs to be fallen back upon.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The T-bit manipulation for syscall error checking had the side effect of
spuriously returning ERESTART* errno values over EINTR. So, we simplify
the error checking a bit and leave the T-bit alone.
Reported-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch optimizes the gpio data register handling for gpio_set_value().
Instead of using the good old spinlock-plus-read-modify-write strategy
we now use a shadow register and atomic operations.
This improves the bitbanging mmc performance on Migo-R from 26 Kbytes/s
to 40 Kbytes/s.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch modifies the table based SuperH gpio implementation to
make use of direct table lookups. With this change the functions
gpio_get_value() and gpio_set_value() are O(1).
Tested on Migo-R using bitbanging mmc. Performance is improved from
11 KBytes/s to 26 Kbytes/s.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Bring sh in line with all the other ports. Not sure how sh missed this
change as all the other arches were being updated ...
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'syscalls' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[CVE-2009-0029] s390 specific system call wrappers
[CVE-2009-0029] System call wrappers part 33
[CVE-2009-0029] System call wrappers part 32
[CVE-2009-0029] System call wrappers part 31
[CVE-2009-0029] System call wrappers part 30
[CVE-2009-0029] System call wrappers part 29
[CVE-2009-0029] System call wrappers part 28
[CVE-2009-0029] System call wrappers part 27
[CVE-2009-0029] System call wrappers part 26
[CVE-2009-0029] System call wrappers part 25
[CVE-2009-0029] System call wrappers part 24
[CVE-2009-0029] System call wrappers part 23
[CVE-2009-0029] System call wrappers part 22
[CVE-2009-0029] System call wrappers part 21
[CVE-2009-0029] System call wrappers part 20
[CVE-2009-0029] System call wrappers part 19
[CVE-2009-0029] System call wrappers part 18
[CVE-2009-0029] System call wrappers part 17
[CVE-2009-0029] System call wrappers part 16
[CVE-2009-0029] System call wrappers part 15
...
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove __attribute__((weak)) from common code sys_pipe implemantation.
IA64, ALPHA, SUPERH (32bit) and SPARC (32bit) have own implemantations
with the same name. Just rename them.
For sys_pipe2 there is no architecture specific implementation.
Cc: Richard Henderson <rth@twiddle.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Make VMAs per mm_struct as for MMU-mode linux. This solves two problems:
(1) In SYSV SHM where nattch for a segment does not reflect the number of
shmat's (and forks) done.
(2) In mmap() where the VMA's vm_mm is set to point to the parent mm by an
exec'ing process when VM_EXECUTABLE is specified, regardless of the fact
that a VMA might be shared and already have its vm_mm assigned to another
process or a dead process.
A new struct (vm_region) is introduced to track a mapped region and to remember
the circumstances under which it may be shared and the vm_list_struct structure
is discarded as it's no longer required.
This patch makes the following additional changes:
(1) Regions are now allocated with alloc_pages() rather than kmalloc() and
with no recourse to __GFP_COMP, so the pages are not composite. Instead,
each page has a reference on it held by the region. Anything else that is
interested in such a page will have to get a reference on it to retain it.
When the pages are released due to unmapping, each page is passed to
put_page() and will be freed when the page usage count reaches zero.
(2) Excess pages are trimmed after an allocation as the allocation must be
made as a power-of-2 quantity of pages.
(3) VMAs are added to the parent MM's R/B tree and mmap lists. As an MM may
end up with overlapping VMAs within the tree, the VMA struct address is
appended to the sort key.
(4) Non-anonymous VMAs are now added to the backing inode's prio list.
(5) Holes may be punched in anonymous VMAs with munmap(), releasing parts of
the backing region. The VMA and region structs will be split if
necessary.
(6) sys_shmdt() only releases one attachment to a SYSV IPC shared memory
segment instead of all the attachments at that addresss. Multiple
shmat()'s return the same address under NOMMU-mode instead of different
virtual addresses as under MMU-mode.
(7) Core dumping for ELF-FDPIC requires fewer exceptions for NOMMU-mode.
(8) /proc/maps is now the global list of mapped regions, and may list bits
that aren't actually mapped anywhere.
(9) /proc/meminfo gains a line (tagged "MmapCopy") that indicates the amount
of RAM currently allocated by mmap to hold mappable regions that can't be
mapped directly. These are copies of the backing device or file if not
anonymous.
These changes make NOMMU mode more similar to MMU mode. The downside is that
NOMMU mode requires some extra memory to track things over NOMMU without this
patch (VMAs are no longer shared, and there are now region structs).
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: New APIs
The old node_to_cpumask/node_to_pcibus returned a cpumask_t: these
return a pointer to a struct cpumask. Part of removing cpumasks from
the stack.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mundt <lethal@linux-sh.org>
arch_setup_additional_pages currently gets two arguments, the binary
format descripton and an indication if the process uses an executable
stack or not. The second argument is not used by anybody, it could
be removed without replacement.
What actually does make sense is to pass an indication if the process
uses the elf interpreter or not. The glibc code will not use anything
from the vdso if the process does not use the dynamic linker, so for
statically linked binaries the architecture backend can choose not
to map the vdso.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We don't really want this enabled by default, but it is still quite
useful for debugging. So, make it conditional and leave it off by
default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the boards that were using cf-enabler "generically"
have switched to setting up their mappings on their own, only the mach-se
boards were left using it. All of the cf-enabler using mach-se boards
use a special initialization of the MRSHPC windows rather than going
through the special PTE as other SH-4 platforms do. This consolidates
the MRSHPC setup logic, hooks it up on the boards that care, and gets rid
of any and all remaining references to cf-enabler.
This has been long overdue, as cf-enabler has been the bane of
arch/sh/kernel for the last 7 years. Good riddance.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nothing is using this any more, so get rid of it before anyone gets the
bright idea to start using it again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the reworked kgdb support, we always detach and reinitialize the
stub. This was mostly a feature for handoffs between sh-ipl+g and the
kgdb stub, but virtually no sh-ipl+g versions ever had this working
right in the first place.
Given that the sh-ipl+g stubs in general use today don't even support
the GDB stub, and we have already killed off the special casing in the
sh-sci serial driver, kill off this now unused symbol too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This migrates from the old bitrotted kgdb stub implementation and moves
to the generic stub. In the process support for SH-2/SH-2A is also added,
which the old stub never provided.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the __mutex_fastpath_xxx() routines to match the semantics
noted in the comment. Previously these were looping rather than doing a
single-pass, which is counter-intuitive, as the slow path takes care of
the looping for us in the event of contention.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the not-so-generic pm code from arch/sh/kernel/pm.c to the
platform directory together with the rest of the hp6xx pm code.
This is done to let non-hp6xx platforms enable CONFIG_PM.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove out-of-date se7343 ioport code including some old support
for unknown-ne2000-pcmcia-card, cf-over-pcmcia and a mysterical
smc91x that once must have been on a special daughterboard.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add 8250 platform data to setup the ST16C2550C chip on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the SH-2A FPU based SH7201 processor subtype.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a simple show_code() that is in turn plugged in to
show_regs() to provide minimal code dumping at the end of the trace.
Built on top of a simple instruction disassembler derived from the
binutils opcode table.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for unaligned loads on SH-4A, using the SH-4A's
neutered movua.l instruction. As movua.l is r0-inspired, stores are
still handled through the packed struct.
Based on asm-generic/unaligned.h by Harvey Harrison.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a pass-through case when ioremapping P4 addresses.
Addresses passed to ioremap() should be physical addresses, so the
best option is usually to convert the virtual address to a physical
address before calling ioremap. This will give you a virtual address
in P2 which matches the physical address and this works well for
most internal hardware blocks on the SuperH architecture.
However, some hardware blocks must be accessed through P4. Converting
the P4 address to a physical and then back to a P2 does not work. One
example of this is the sh7722 TMU block, it must be accessed through P4.
Without this patch P4 addresses will be mapped using PTEs which
requires the page allocator to be up and running.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add fast mutex path implementation for the SH4A architecture
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I'm using these constants in support of an in-house development board,
and thought they may be useful to other users of SH7709.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>