The properties indicates that the hardware supports waking up via magic
packet.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo introduced by "powerpc: Add TBI PHY node to first MDIO bus"
from Andy Fleming.
It's device_type rather than device-type, which causes the mdio probe to
fail thus making all gianfar ethernet interfaces unusable.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is here most likely since the FSL bsp. Back in the FSL bsp it was
set to 50Mhz and working. However the driver divided the SoC freq. only
by 2. According to the TRM the platform clock (which the manual refers
in its formula) is the system clock divided by two. So in the end it has
to divide by 4 and this is what the fsl-spi driver in tree is doing.
Since then the flash is not wokring I guess. After chaning the freq from
50Mhz to 40Mhz like others do then I can access the flash.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is not at 0xffa00000. According to current u-boot source the NAND
controller is always at 0xff800000 and it is either at CS0 or CS1
depending on NAND or NAND+NOR mode. In 36bit mode it is shifted to
0xfff800000 but it has always an eight there and never an A.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the file "arch/powerpc/sysdev/fsl_rmu.c", there will be some compile
errors while using the corenet64_smp_defconfig:
.../fsl_rmu.c:315: error: cast from pointer to integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:330: error: cast to pointer from integer of different size
.../fsl_rmu.c:332: error: cast to pointer from integer of different size
.../fsl_rmu.c:339: error: cast to pointer from integer of different size
.../fsl_rmu.c:340: error: cast to pointer from integer of different size
.../fsl_rmu.c:341: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:659: error: cast from pointer to integer of different size
.../fsl_rmu.c:659: error: format '%8.8x' expects type 'unsigned int',
but argument 5 has type 'size_t'
.../fsl_rmu.c:985: error: cast from pointer to integer of different size
.../fsl_rmu.c:997: error: cast to pointer from integer of different size
Rewrote the corresponding code with the support of 64bit building.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the file "arch/powerpc/sysdev/fsl_rio.c", there will be some relocation
errors while using the corenet64_smp_defconfig:
WARNING: modpost: Found 6 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
LD .tmp_vmlinux1
arch/powerpc/sysdev/built-in.o:(__ex_table+0x0):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3208
arch/powerpc/sysdev/built-in.o:(__ex_table+0x2):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'
arch/powerpc/sysdev/built-in.o:(__ex_table+0x4):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3230
arch/powerpc/sysdev/built-in.o:(__ex_table+0x6):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+c
arch/powerpc/sysdev/built-in.o:(__ex_table+0x8):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3250
arch/powerpc/sysdev/built-in.o:(__ex_table+0xa):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+18
Rewrote the corresponding code with the support of 64bit building.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add usb controller version info for the following:
MPC8536, P1010, P1020, P1021, P1022, P1023, P2020, P2041,
P3041, P3060, P5020
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2020RDB-PC Board shares the same design(PCB) as P102x RDB style platforms.
The difference between this platform and the already existing P2020RDB
is mainly with respect to DDR. The P2020RDB-PC has a DDR3 memory.
The P2020RDB-PC also has a CPLD device connected to local bus.
The main differences from the P102x RDB-PC is 64-bit DDR and SYSCLK of
100Mhz.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
- x1 PCIe slot or x1 PCIe to dual SATA controller
- x1 mini-PCIe slot
USB 2.0
- ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic’s GL850A
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ENDPROC() on sys_fadvise64_c6x() in arch/c6x/kernel/entry.S is
outside of the conditional block with the matching ENTRY() macro. This
leads a newer (v2.22 vs. v2.20) assembler to complain:
/tmp/ccGZBaPT.s: Assembler messages:
/tmp/ccGZBaPT.s: Error: .size expression for sys_fadvise64_c6x does not evaluate to a constant
The conditional block became dead code when c6x switched to generic
unistd.h and should be removed along with the offending ENDPROC().
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
in commit 7230c56441
"powerpc: Rework lazy-interrupt handling"
I introduced a regression, accidentally calling irq tracing twice
and not properly restoring a clobbered register (r7) later used
for writing to the MSR.
This caused lockups when booting on a G5 with lockdep enabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ath79 usb driver doesn't do anything special and is now converted
to the generic ehci and ohci driver.
This was tested on a TP-Link TL-WR1043ND (AR9132)
Acked-by: Gabor Juhos <juhosg@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
CC: linux-mips@linux-mips.org
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The registers that describe size supported by TLB are different on MMU
v2 as well as we support power of two page sizes. For now we continue
to assume that FSL variable size array supports all page sizes up to the
maximum one reported in TLB1PS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The SERIAL_8250_EXTENDED option just enables access to other
less regularly used options, like SERIAL_8250_SHARE_IRQ.
Select it to get rid of this warning when selecting the child
option living underneath it.
warning: (FSL_SOC_BOOKE && SERIAL_8250_RM9K) selects
SERIAL_8250_SHARE_IRQ which has unmet direct dependencies
(HAS_IOMEM && SERIAL_8250_EXTENDED)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mixed bag here, a few minor diagnostic tweaks, some driver enhancements
and the dmaengine conversion for ep93xx drivers which was tested a while
ago and just waiting for a signoff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=AOrs
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
Linus decided to go for another week so here's a few more updates - a
mixed bag here, a few minor diagnostic tweaks, some driver enhancements
and the dmaengine conversion for ep93xx drivers which was tested a while
ago and just waiting for a signoff.
Pull arch/tile update to run "make minconfig" on the tile defconfigs
from Chris Metcalf.
This removes almost three thousand lines of inane defconfig chatter.
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile/configs: convert to minimal configs via "make savedefconfig"
When handling Interrupt Source Override in MADT table, the default
ISA IRQ trigger model and polarity should be edge-rising.
Current IA64 implmentation doesn't follow the specification and
set default ISA IRQ trigger model as level-low. With that wrong
configuration and when system runs out of interrupt vectors,
it will cause vector sharing among edge triggered ISA IRQ and
level triggered PCI IRQ, then interrupt storm. So change the code
to follow the specification.
Signed-off-by: Liu Jiang <jiang.liu@huawei.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds support cpufreq for EXYNOS5250 SoC. Basically,
the exynos-cpufreq.c is used commonly and exynos5250-cpufreq.c
is used for EXYNOS5250(two Cortex-A15 cores) SoC.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch adds support cpufreq for EXYNOS4X12 SoCs. Basically,
the exynos-cpufreq.c is used commonly and exynos4x12-cpufreq.c
is used for EXYNOS4212(two Cortex-A9 cores) and EXYNOS4412(four
Cortex-A9 cores) SoCs.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Move APIC ID validity check into platform APIC code, so it can
be overridden when needed. For NumaChip systems, always trust
MADT, as it's constructed with high APIC IDs.
Behaviour verifies on standard x86 systems and on NumaChip
systems with this, and compile-tested with allyesconfig.
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Reviewed-by: Steffen Persvold <sp@numascale.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1331709454-27966-1-git-send-email-daniel@numascale-asia.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into x86/mce
Merge reason: Update from an ancient -rc1 base to an almost-final stable kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Newer version of binutils are more strict about specifying the
correct options to enable certain classes of instructions.
The sparc32 build is done for v7 in order to support sun4c systems
which lack hardware integer multiply and divide instructions.
So we have to pass -Av8 when building the assembler routines that
use these instructions and get patched into the kernel when we find
out that we have a v8 capable cpu.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull arch/tile update from Chris Metcalf
"These include a couple of queued-up minor bug fixes from the
community, a fix to unbreak the sysfs hooks in tile, and syncing up
the defconfigs."
Ugh. defconfigs updates without "make minconfig". Tons of ugly
pointless lines there, I suspect.
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: Use set_current_blocked() and block_sigmask()
arch/tile: misplaced parens near likely
arch/tile: sync up the defconfig files to the tip
arch/tile: Fix up from commit 8a25a2fd12
Pull perf fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf record: Fix buffer overrun bug in tracepoint_id_to_path()
perf/x86: Fix local vs remote memory events for NHM/WSM
Convert mx27vis-aic32x4 to platform driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
When a machine boots up, the TSC generally gets reset. However,
when kexec is used to boot into a kernel, the TSC value would be
carried over from the previous kernel. The computation of
cycns_offset in set_cyc2ns_scale is prone to an overflow, if the
machine has been up more than 208 days prior to the kexec. The
overflow happens when we multiply *scale, even though there is
enough room to store the final answer.
We fix this issue by decomposing tsc_now into the quotient and
remainder of division by CYC2NS_SCALE_FACTOR and then performing
the multiplication separately on the two components.
Refactor code to share the calculation with the previous
fix in __cycles_2_ns().
Signed-off-by: Salman Qazi <sqazi@google.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Turner <pjt@google.com>
Cc: john stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20120310004027.19291.88460.stgit@dungbeetle.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently pcpu_devices->panic_stack is passed to pcpu_delegate() in
smp_call_ipl_cpu(). This is wrong because pcpu_delegate() expects
the bottom (high address) of the stack and pcpu_devices->panic_stack
points to the top (low address). We now pass the bottom of the stack
which is pcpu_devices->panic_stack + PAGE_SIZE.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk9dltgACgkQGkmNcg7/o7joMQCgnQlwX1MKLNvKtvxvzz7biF48
aigAoLELf2MGKHFs/yMilS/NMZTJR3Pd
=ttKa
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh-sci / PM: Avoid deadlocking runtime PM
sh: fix up the ubc clock definition for sh7785.
sh: add parameter for RSPI in clock-sh7757
sh: Fix sh2a vbr table for more than 255 irqs
With the recent changes to clear_IO_APIC_pin() which tries to
clear remoteIRR bit explicitly, some of the users started to see
"Unable to reset IRR for apic .." messages.
Close look shows that these are related to bogus IO-APIC entries
which return's all 1's for their io-apic registers. And the
above mentioned error messages are benign. But kernel should
have ignored such io-apic's in the first place.
Check if register 0, 1, 2 of the listed io-apic are all 1's and
ignore such io-apic.
Reported-by: Álvaro Castillo <midgoon@gmail.com>
Tested-by: Jon Dufresne <jon@jondufresne.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: kernel-team@fedoraproject.org
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1331577393.31585.94.camel@sbsiddha-desk.sc.intel.com
[ Performed minor cleanup of affected code. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To show how the pin configuration is used on the U300, let's
include some configs for two GPIO pins.
ChangeLog v1->v2:
- Provide a better example, set the clock return pin to pull-up
and set the card detect pin to high impedance.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The structures, passed to the sh_mobile_lcdcfb driver through platform
data, are read only by the driver. Make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The marker and cache ICBs are now allocated automatically, there's no
need to specify them manually anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of requiring the users to hardcode MERAM allocation in platform
data, allocate blocks at runtime using genalloc.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The MERAM resource currently combines both the registers space and the
MERAM space. Only the register space needs to be ioremapped, split the
resource to make that possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The struct sh_mobile_lcdc_chan_cfg platform data contains a list of
video modes. Name the lcd_cfg and num_cfg fields to reflect that they
describe video modes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make sure the transmitter devices get registered before the associated
LCDC devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
I got somewhat tired of having to decode hex numbers..
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/n/tip-0vsy1sgywc4uar3mu1szm0rg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stepan found:
CPU0 CPUn
_cpu_up()
__cpu_up()
boostrap()
notify_cpu_starting()
set_cpu_online()
while (!cpu_active())
cpu_relax()
<PREEMPT-out>
smp_call_function(.wait=1)
/* we find cpu_online() is true */
arch_send_call_function_ipi_mask()
/* wait-forever-more */
<PREEMPT-in>
local_irq_enable()
cpu_notify(CPU_ONLINE)
sched_cpu_active()
set_cpu_active()
Now the purpose of cpu_active is mostly with bringing down a cpu, where
we mark it !active to avoid the load-balancer from moving tasks to it
while we tear down the cpu. This is required because we only update the
sched_domain tree after we brought the cpu-down. And this is needed so
that some tasks can still run while we bring it down, we just don't want
new tasks to appear.
On cpu-up however the sched_domain tree doesn't yet include the new cpu,
so its invisible to the load-balancer, regardless of the active state.
So instead of setting the active state after we boot the new cpu (and
consequently having to wait for it before enabling interrupts) set the
cpu active before we set it online and avoid the whole mess.
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1323965362.18942.71.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This was inspired by mchehab@redhat.com's observation that we
didn't have EDAC configured on by default in both files. In addition,
we were setting INITRAMFS_SOURCE to a non-empty string, which isn't
a very common default and required editing to do test builds.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This was Kay Siever's bombing to convert 'cpu' to a regular subsystem.
The change left a bogus second argument to sysfs_create_file().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The McBSP driver stack has been moved to ASoC. The CONFIG_OMAP_MCBSP will
be removed since the CONFIG_SND_OMAP_SOC_MCBSP will trigger to build the
McBSP (audio) drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Clock signal muxing, and functional clock related defines are only needed
in ASoC drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
On OMAP2/3 McBSP1 port has 6 pin setup, while on OMAP4 the port is McBSP4.
Implement the CLKR/FSR clock mux selection for OMAP4, and make sure that
we add the correct callback for the correct port across supported OMAP
versions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The driver for omap-mcbsp-dai no longer exist since it has been merged with
the omap-mcbsp driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The OMAP McBSP driver stack used to contain two different
drivers. One of them was used as kind low-level access to
the IP, while the other driver was the ASoC DAI driver.
There were global, shared structures, in different places,
the McBSP instances are reffered with id numbers (sometimes
0 based, in other cases 1 based id numbers).
Create one single driver for OMAP McBSP with name: omap-mcbsp.
Convert the old omap-mcbsp driver initially to be a library
for the omap-mcbsp DAI driver. With this change we can get rid
of all global variables, structures.
Further cleanup is coming...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Move most of the content of the plat/mcbsp.h header file under
sound/soc/omap/ to help further cleanups.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to consolidate the McBSP driver move it out from
arch/arm/plat-omap directory under sound/soc/omap/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Convert the plat-omap/mcbsp.c driver to be proper platform driver.
Remove the omap_mcbsp_init function call which was called from
mach-omap1/2/mcbsp.c to register the platform driver for the just
created platform device in the same function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The cpu_is_omap4430() macro always return with 0. Use the correct
cpu_is_omap443x() to check for Panda revision.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Because the vmcore_info pointer is not 8 byte aligned it never should
not be accessed directly. The reason is that the compiler assumes that
64 bit pointer are always double word aligned. To ensure save access,
the vmcore_info type in struct lowcore is changed from u64 to an u8[8]
array and a comment is added.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The first line of a stack dump has a wrong (no) indentation.
Just fix this after more than 10 years.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to allow kdump based stand-alone dump, some information
has to be passed from the old kernel to the new dump kernel. This
is done via a the struct "os_info" that contains the following fields:
* crashkernel base and size
* reipl block
* vmcoreinfo
* init function
A pointer to os_info is stored at a well known storage location
and the whole structure as well as all fields are secured with
checksums.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures.
In the past some architectures got this code wrong, so using this
helper function should stop that from happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the following mechanisms are available to move active
Linux on System z instances between machines:
* z/VM 6.2 SSI (Single System Image)
* Suspend/resume
For moving Linux instances in this patch the term LGR (Linux Guest
Relocation) is used. Because such an operation is critical, it
should be detectable from Linux. With this patch for both, a live
system and a kernel dump, the information about LGRs is accessible.
To identify a guest, stsi and stfle data is used. A new function
lgr_info_log() compares the current data (lgr_info_cur) with the
last recorded one (lgr_info_last). In case the two data sets differ,
lgr_info_cur is logged to the "lgr" s390dbf.
The following trigger points call lgr_info_log():
* panic
* die
* kdump
* LGR timer
* PSW restart
* QDIO recovery
* resume
This patch also changes the s390dbf hex_ascii view. Now only printable ASCII
characters are shown.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The external interrupt handlers have a parameter called ext_int_code.
Besides the name this paramter does not only contain the ext_int_code
but in addition also the "cpu address" (POP) which caused the external
interrupt.
To make the code a bit more obvious pass a struct instead so the called
function can easily distinguish between external interrupt code and
cpu address. The cpu address field however is named "subcode" since
some external interrupt sources do not pass a cpu address but a
different parameter (or none at all).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Set __ARCH_IRQ_EXIT_IRQS_DISABLED in order to optimize irq_exit() a
bit, since we call __do_softirq() instead of do_softirq().
This saves several needless checks, pointless interrupt disabling
and an extra branch.
If do_softirq() gets called from process context we still switch to
the async stack.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the new copy_to_absolute_zero() function instead of manual "stura"
and "sturg" to make the code shorter and more readable.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Whenever the cpu loads an enabled wait PSW it will appear as idle to the
underlying host system. The code in default_idle calls vtime_stop_cpu
which does the necessary voodoo to get the cpu time accounting right.
The udelay code just loads an enabled wait PSW. To correct this rework
the vtime_stop_cpu/vtime_start_cpu logic and move the difficult parts
to entry[64].S, vtime_stop_cpu can now be called from anywhere and
vtime_start_cpu is gone. The correction of the cpu time during wakeup
from an enabled wait PSW is done with a critical section in entry[64].S.
As vtime_start_cpu is gone, s390_idle_check can be removed as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define struct pcpu and merge some of the NR_CPUS arrays into it, including
__cpu_logical_map, current_set and smp_cpu_state. Split smp related
functions to those operating on physical cpus and the functions operating
on a logical cpu number. Make the functions for physical cpus use a
pointer to a struct pcpu. This hides the knowledge about cpu addresses in
smp.c, entry[64].S and swsusp_asm64.S, thus remove the sigp.h header.
The PSW restart mechanism is used to start secondary cpus, calling a
function on an online cpu, calling a function on the ipl cpu, and for
the nmi signal. Replace the different assembler functions with a
single function restart_int_handler. The new entry point calls a function
whose pointer is stored in the lowcore of the target cpu and it can wait
for the source cpu to stop. This covers all existing use cases.
Overall the code is now simpler and there are ~380 lines less code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 16 bit value at the lowcore location with offset 0x84 is the
cpu address that is associated with an external interrupt. Rename
the field from cpu_addr to ext_cpu_addr to make that clear.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With gcc 4.6.0 we get a false compile warning:
arch/s390/kernel/setup.c: In function 'setup_arch':
arch/s390/kernel/setup.c:767:3: warning: 'msg' may be used
uninitialized in this function [-Wuninitialized]
arch/s390/kernel/setup.c:753:8: note: 'msg' was declared here
This patch makes gcc quiet.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For the hypervisor to take advantage of the MWAIT support it needs
to extract from the ACPI _CST the register address. But the
hypervisor does not have the support to parse DSDT so it relies on
the initial domain (dom0) to parse the ACPI Power Management information
and push it up to the hypervisor. The pushing of the data is done
by the processor_harveset_xen module which parses the information that
the ACPI parser has graciously exposed in 'struct acpi_processor'.
For the ACPI parser to also expose the Cx states for MWAIT, we need
to expose the MWAIT capability (leaf 1). Furthermore we also need to
expose the MWAIT_LEAF capability (leaf 5) for cstate.c to properly
function.
The hypervisor could expose these flags when it traps the XEN_EMULATE_PREFIX
operations, but it can't do it since it needs to be backwards compatible.
Instead we choose to use the native CPUID to figure out if the MWAIT
capability exists and use the XEN_SET_PDC query hypercall to figure out
if the hypervisor wants us to expose the MWAIT_LEAF capability or not.
Note: The XEN_SET_PDC query was implemented in c/s 23783:
"ACPI: add _PDC input override mechanism".
With this in place, instead of
C3 ACPI IOPORT 415
we get now
C3:ACPI FFH INTEL MWAIT 0x20
Note: The cpu_idle which would be calling the mwait variants for idling
never gets set b/c we set the default pm_idle to be the hypercall variant.
Acked-by: Jan Beulich <JBeulich@suse.com>
[v2: Fix missing header file include and #ifdef]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We needed that call in the past to force the kernel to use
default_idle (which called safe_halt, which called xen_safe_halt).
But set_pm_idle_to_default() does now that, so there is no need
to use this boot option operand.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We need to merge this ahead of some of the cleanup because a lot of needed
cleanup spans both new and old chips. If we try and clean up and the merge
we end up fighting ourselves.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[With a load of the cleanup stuff folded in, register stuff reworked sanely]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit f0fbf0abc0 ("x86: integrate delay functions") converted
delay_tsc() into a random delay generator for 64 bit. The reason is
that it merged the mostly identical versions of delay_32.c and
delay_64.c. Though the subtle difference of the result was:
static void delay_tsc(unsigned long loops)
{
- unsigned bclock, now;
+ unsigned long bclock, now;
Now the function uses rdtscl() which returns the lower 32bit of the
TSC. On 32bit that's not problematic as unsigned long is 32bit. On 64
bit this fails when the lower 32bit are close to wrap around when
bclock is read, because the following check
if ((now - bclock) >= loops)
break;
evaluated to true on 64bit for e.g. bclock = 0xffffffff and now = 0
because the unsigned long (now - bclock) of these values results in
0xffffffff00000001 which is definitely larger than the loops
value. That explains Tvortkos observation:
"Because I am seeing udelay(500) (_occasionally_) being short, and
that by delaying for some duration between 0us (yep) and 491us."
Make those variables explicitely u32 again, so this works for both 32
and 64 bit.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # >= 2.6.27
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two fixes are queued up. The first is an additional fix for the OMAP
initialization order issue and the second patch fixes a possible section
mismatch which can lead to a kernel crash in the AMD IOMMU driver when
suspend/resume is used and the compiler has not inlined the
iommu_set_device_table function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPWgA/AAoJECvwRC2XARrj7voQAN6evWicqjRDiXQgEC3muQFU
OrA/Jz/i7+pHEYXcsTt0xHLb8juZNJAdkJjToB+oz7i/7D+TYRmJe+QRNkVmw7Ld
d3DbUSUi9B3agvGblosKV3DYM8By1vTn9Gy2GNatW1yPuo5o4FHK2ePC5sn8Z/8z
qwTZZnmvqluz7frNiw6Y3bNOqLd46z+9thUOoKmRn/fo3vKCOOVvb85yu1m/uqy6
Dmpn6ep0w53jK29ZTKWcL8PW0YrLTEfszhMcVshFT+Y7GVSGnSxwgSh1fnZm/WL6
z11L57dI0+7RS/z+cw+ko7ymIloV2v4ABRArMPIoLgbIQT0lidDNSqOQnPvWaBek
MwdLL8W64lt2h4T7bLhDNRSDggWCX+EJYlk87O4hJYt4n57c3yT55z2+BGdoFivZ
tzPshNWN4KVDMZCU6sTvzvz6eErwvro5wlVM2WxDVfXTxn6UTblP5uIQDGb2zVA9
G95kK/OlK/s+giwOSOKxtR62livKEAuJ2Croa5LsdJnLdCo6ipvIz9cuAG6eij2W
tulJQUN3FZr288iUAOPQ9xj6hWYM9RXqoYBxAHAvgYgGuirj9E6hjk/fL0y6XGQk
jcg0bCdJjh2RzsLZR0eeslybtlrvUsBWYCPYCAAmRjUYHwZ6s822aO7qh0VnrFuQ
csH09+3B0twvJ+ZRJibN
=PZDd
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull two IOMMU fixes from Joerg Roedel:
"The first is an additional fix for the OMAP initialization order issue
and the second patch fixes a possible section mismatch which can lead
to a kernel crash in the AMD IOMMU driver when suspend/resume is used
and the compiler has not inlined the iommu_set_device_table function."
* tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
x86/amd: iommu_set_device_table() must not be __init
ARM: OMAP: fix iommu, not mailbox
Otherwise we will get:
arch/arm/plat-omap/fb.c:101: error: expected ‘)’ before ‘*’ token
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current implementation of lazy interrupts handling has some
issues that this tries to address.
We don't do the various workarounds we need to do when re-enabling
interrupts in some cases such as when returning from an interrupt
and thus we may still lose or get delayed decrementer or doorbell
interrupts.
The current scheme also makes it much harder to handle the external
"edge" interrupts provided by some BookE processors when using the
EPR facility (External Proxy) and the Freescale Hypervisor.
Additionally, we tend to keep interrupts hard disabled in a number
of cases, such as decrementer interrupts, external interrupts, or
when a masked decrementer interrupt is pending. This is sub-optimal.
This is an attempt at fixing it all in one go by reworking the way
we do the lazy interrupt disabling from the ground up.
The base idea is to replace the "hard_enabled" field with a
"irq_happened" field in which we store a bit mask of what interrupt
occurred while soft-disabled.
When re-enabling, either via arch_local_irq_restore() or when returning
from an interrupt, we can now decide what to do by testing bits in that
field.
We then implement replaying of the missed interrupts either by
re-using the existing exception frame (in exception exit case) or via
the creation of a new one from an assembly trampoline (in the
arch_local_irq_enable case).
This removes the need to play with the decrementer to try to create
fake interrupts, among others.
In addition, this adds a few refinements:
- We no longer hard disable decrementer interrupts that occur
while soft-disabled. We now simply bump the decrementer back to max
(on BookS) or leave it stopped (on BookE) and continue with hard interrupts
enabled, which means that we'll potentially get better sample quality from
performance monitor interrupts.
- Timer, decrementer and doorbell interrupts now hard-enable
shortly after removing the source of the interrupt, which means
they no longer run entirely hard disabled. Again, this will improve
perf sample quality.
- On Book3E 64-bit, we now make the performance monitor interrupt
act as an NMI like Book3S (the necessary C code for that to work
appear to already be present in the FSL perf code, notably calling
nmi_enter instead of irq_enter). (This also fixes a bug where BookE
perfmon interrupts could clobber r14 ... oops)
- We could make "masked" decrementer interrupts act as NMIs when doing
timer-based perf sampling to improve the sample quality.
Signed-off-by-yet: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2:
- Add hard-enable to decrementer, timer and doorbells
- Fix CR clobber in masked irq handling on BookE
- Make embedded perf interrupt act as an NMI
- Add a PACA_HAPPENED_EE_EDGE for use by FSL if they want
to retrigger an interrupt without preventing hard-enable
v3:
- Fix or vs. ori bug on Book3E
- Fix enabling of interrupts for some exceptions on Book3E
v4:
- Fix resend of doorbells on return from interrupt on Book3E
v5:
- Rebased on top of my latest series, which involves some significant
rework of some aspects of the patch.
v6:
- 32-bit compile fix
- more compile fixes with various .config combos
- factor out the asm code to soft-disable interrupts
- remove the C wrapper around preempt_schedule_irq
v7:
- Fix a bug with hard irq state tracking on native power7
Ok, this is hacky, and only works on little-endian machines with goo
unaligned handling. And even then only with CONFIG_DEBUG_PAGEALLOC
disabled, since it can access up to 7 bytes after the pathname.
But it runs like a bat out of hell.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One samsung build fix due to a mis-applied patch, and a small set of OMAP fixes.
This should be the last from arm-soc for 3.3, hopefully.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PLTM
-----END PGP SIGNATURE-----
Merge tag 'fixes-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull last minute fixes from Olof Johansson:
"One samsung build fix due to a mis-applied patch, and a small set of
OMAP fixes. This should be the last from arm-soc for 3.3, hopefully."
* tag 'fixes-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: S3C2440: Fixed build error for s3c244x
ARM: OMAP2+: Fix module build errors with CONFIG_OMAP4_ERRATA_I688
ARM: OMAP: id: Add missing break statement in omap3xxx_check_revision
ARM: OMAP2+: Remove apply_uV constraints for fixed regulator
ARM: OMAP: irqs: Fix NR_IRQS value to handle PRCM interrupts
Fixes up a duplicate #include, adds an empty implementation of
of_find_compatible_node() and make git ignore .dtb files. And fix
up bus name on OF described PHYs. Nothing exciting here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/fxH
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull minor devicetree bug fixes and documentation updates from Grant Likely:
"Fixes up a duplicate #include, adds an empty implementation of
of_find_compatible_node() and make git ignore .dtb files. And fix up
bus name on OF described PHYs. Nothing exciting here."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
doc: dt: Fix broken reference in gpio-leds documentation
of/mdio: fix fixed link bus name
of/fdt.c: asm/setup.h included twice
of: add picochip vendor prefix
dt: add empty of_find_compatible_node function
ARM: devicetree: Add .dtb files to arch/arm/boot/.gitignore
With the original EEH implementation, the access to config space of
the corresponding PCI device is done by RTAS sensitive function. That
depends on pci_dn heavily. That would limit EEH extension to other
platforms like powernv because other platforms might have different
ways to access PCI config space.
The patch splits those functions used to access PCI config space
and implement them in platform related EEH component. It would be
helpful to support EEH on multiple platforms simutaneously in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the original EEH implementation, the EEH global statistics
are maintained by individual global variables. That makes the
code a little hard to maintain.
The patch introduces extra struct eeh_stats for the EEH global
statistics so that it can be maintained in collective fashion.
It's the rework on the corresponding v5 patch. According to
the comments from David Laight, the EEH global statistics have
been changed for a litte bit so that they have fixed-type of
"u64". Also, the format used to print them has been changed to
"%llu" based on David's suggestion. Also, the output format of
EEH global statistics should be kept as intacted according to
Michael's suggestion that there might be tools parsing them.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pci_dn has been replaced with eeh_dev. In order to comply with
the rule, the EEH platform implementation on pSeries should also
be adjusted for a little bit so that it will depend on eeh_dev instead
of pci_dn.
The patch replaces pci_dn with eeh_dev. The corresponding information
will be retrieved from eeh_dev instead of pci_dn.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The original EEH implementation is heavily depending on struct pci_dn.
We have to put EEH related information to pci_dn. Actually, we could
split struct pci_dn so that the EEH sensitive information to form an
individual struct, then EEH looks more independent.
The patch replaces pci_dn with eeh_dev for EEH aux components like
event and driver. Also, the eeh_event struct has been adjusted for
a little bit since eeh_dev has linked the associated FDT (Flat Device
Tree) node and PCI device. It's not necessary for eeh_event struct to
trace FDT node and PCI device. We can just simply to trace eeh_dev in
eeh_event.
The patch also renames function pcid_name() to eeh_pcid_name(), which
should be missed in the previous patch where the EEH aux components
have been cleaned up.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The original EEH implementation is heavily depending on struct pci_dn.
We have to put EEH related information to pci_dn. Actually, we could
split struct pci_dn so that the EEH sensitive information to form an
individual struct, then EEH looks more independent.
The patch replaces pci_dn with eeh_dev for EEH core.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With original EEH implementation, struct pci_dn is used while building
PCI I/O address cache, which helps on searching the corresponding
PCI device according to the given physical I/O address. Besides, pci_dn
is associated with the corresponding PCI device while building its
I/O cache.
The patch replaces struct pci_dn with struct eeh_dev so that EEH address
cache won't depend on struct pci_dn. That will help EEH to become an
independent module in future. Besides, the binding of eeh_dev and PCI
device is done while building PCI device I/O cache.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With original EEH implementation, all EEH related statistics have
been put into struct pci_dn. We've introduced struct eeh_dev to
replace struct pci_dn in EEH core components, including EEH sysfs
component.
The patch shows EEH statistics from struct eeh_dev instead of struct
pci_dn in EEH sysfs component. Besides, it also fixed the EEH device
retrieval from PCI device, which was introduced by the previous patch
in the series of patch.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Original EEH implementation depends on struct pci_dn heavily. However,
EEH shouldn't depend on that actually because EEH needn't share much
information with other PCI components. That's to say, EEH should have
worked independently.
The patch introduces struct eeh_dev so that EEH core components needn't
be working based on struct pci_dn in future. Also, struct pci_dn, struct
eeh_dev instances are created in dynamic fasion and the binding with EEH
device, OF node, PCI device is implemented as well.
The EEH devices are created after PHBs are detected and initialized, but
PCI emunation hasn't started yet. Apart from that, PHB might be created
dynamically through DLPAR component and the EEH devices should be creatd
as well. Another case might be OF node is created dynamically by DR
(Dynamic Reconfiguration), which has been defined by PAPR. For those OF
nodes created by DR, EEH devices should be also created accordingly. The
binding between EEH device and OF node is done while the EEH device is
initially created.
The binding between EEH device and PCI device should be done after PCI
emunation is done. Besides, PCI hotplug also needs the binding so that
the EEH devices could be traced from the newly coming PCI buses or PCI
devices.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch does some cleanup on the function names of EEH
aux components. Currently, only couple of function names from
eeh_cache have been adjusted so that:
* The function name has prefix "eeh_addr_cache".
* Move around pci_addr_cache_build() in the header file
to reflect function call sequence.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're several EEH aux components and the patch does some cleanup
for them so that they look more clean.
* Duplicated comments have been removed from the header file.
* Comments have been reorganized so that it looks more clean.
* The leading comments of functions are adjusted for a little
bit so that the result of "make pdfdocs" would be more
unified.
* Function calls "xxx ()" has been replaced by "xxx()".
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In order to enable particular PCI device, which has been included
in the parent PE. The involved PCI bridges should be enabled explicitly
if there has. On pSeries platform, there're dedicated RTAS calls
to fulfil the purpose.
The patch implements the function of configuring PCI bridges through
the dedicated RTAS calls. Besides, the function has been abstracted
by struct eeh_ops::configure_bridge so that the EEH core components
could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On RTAS compliant pSeries platform, one dedicated RTAS call has
been introduced to retrieve EEH temporary or permanent error log.
The patch implements the function of retriving EEH error log through
RTAS call. Besides, it has been abstracted by struct eeh_ops::get_log
so that EEH core components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On RTAS compliant pSeries platform, there is a dedicated RTAS call
(ibm,set-slot-reset) to reset the specified PE. Furthermore, two
types of resets are supported: hot and fundamental. the type of
reset is to be used actually depends on the included PCI device's
requirements.
The patch implements resetting PE on pSeries platform through RTAS
call. Besides, it has been abstracted through struct eeh_ops::reset
so that EEH core components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pSeries platform, the PE state might be temporarily unavailable.
In that case, the firmware will return the corresponding wait time.
That means the kernel has to wait for appropriate time in order to
get the PE state.
The patch does the implementation for that. Besides, the function
has been abstracted through struct eeh_ops::wait_state so that EEH core
components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pSeries platform, there're 2 dedicated RTAS calls introduced to
retrieve the corresponding PE's state: ibm,read-slot-reset-state and
ibm,read-slot-reset-state2.
The patch implements the retrieval of PE's state according to the
given PE address. Besides, the implementation has been abstracted by
struct eeh_ops::get_state so that EEH core components could support
multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 types of addresses used for EEH operations. The first
one would be BDF (Bus/Device/Function) address which is retrieved
from the reg property of the corresponding FDT node. Another one
is PE address that should be enquired from firmware through RTAS
call on pSeries platform. When issuing EEH operation, the PE address
has precedence over BDF address.
The patch implements retrieving PE address according to the given
BDF address on pSeries platform. Also, the struct eeh_early_enable_info
has been removed since the information can be figured out from
dn->pdn->phb->buid directly and that simplifies the code.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 4 EEH operations that are covered by the dedicated RTAS
call <ibm,set-eeh-option>: enable or disable EEH, enable MMIO and
enable DMA. At early stage of system boot, the EEH would be tried
to enable on PCI device related device node. MMIO and DMA for
particular PE should be enabled when doing recovery on EEH errors
so that the PE could function properly again.
The patch implements it and abstract that through struct
eeh_ops::set_eeh. It would be help for EEH to support multiple
platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The platform specific EEH operations have been abstracted by
struct eeh_ops. The individual platroms, including pSeries, needs
doing necessary initialization before the platform dependent EEH
operations work properly.
The patch is addressing that and do necessary platform initialization
for pSeries platform. More specificly, it will figure out the tokens
of EEH related RTAS calls.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
EEH has been implemented on RTAS-compliant pSeries platform.
That's to say, the EEH operations will be implemented through RTAS
calls eventually. The situation limited feasible extension on EEH.
In order to support EEH on multiple platforms like pseries and powernv
simutaneously. We have to split the platform dependent EEH options
up out of current implementation.
The patch addresses supporting EEH on multiple platforms. The pseries
platform dependent EEH operations will be abstracted by struct eeh_ops.
EEH core components will be built based on the registered EEH operations.
With the mechanism, what the individual platform needs to do is implement
platform dependent EEH operations.
For now, the pseries platform is covered under the mechanism. That means
we have to think about other platforms to support EEH, like powernv.
Besides, we only have framework for the mechanism and we have to implement
it for pseries platform later.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH has been implemented on pSeries platform. The original
code looks a little bit nasty. The patch does cleanup on the
current EEH implementation so that it looks more clean.
* Try adding prefix "eeh" for functions.
* Some function names have been adjusted so that they looks
shorter and meaningful.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH has been implemented on pSeries platform. The original
code looks a little bit nasty. The patch does cleanup on the
current EEH implementation so that it looks more clean.
* Duplicated comments have been removed from the corresponding
header files.
* Comments have been reorganized so that it looks more clean.
* The leading comments of functions are adjusted for a little
bit so that the result of "make pdfdocs" would be more
unified.
* Function definitions and calls have unified format as "xxx()".
That means the format "xxx ()" has been replaced by "xxx()".
* There're multiple functions implemented for resetting PE. The
position of those functions have been move around so that they
are adjacent to each other to reflect their relationship.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 64-bit, the mfmsr instruction can be quite slow, slower
than loading a field from the cache-hot PACA, which happens
to already contain the value we want in most cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We were using CR0.EQ after EXCEPTION_COMMON, hoping it still
contained whether we came from userspace or kernel space.
However, under some circumstances, EXCEPTION_COMMON will
call C code and clobber non-volatile registers, so we really
need to re-load the previous MSR from the stackframe and
re-test.
While there, invert the condition to make the fast path more
obvious and remove the BUG_OPCODE which was a debugging
leftover and call .ret_from_except as we should.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running under a hypervisor that supports stolen time accounting,
we may call C code from the macro EXCEPTION_PROLOG_COMMON in the
exception entry path, which clobbers CR0.
However, the FPU and vector traps rely on CR0 indicating whether we
are coming from userspace or kernel to decide what to do.
So we need to restore that value after the C call
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also use local_paca instead of get_paca() to avoid getting into
the smp_processor_id() debugging code from the debugger
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Other architectures such as x86 and ARM have been growing
new support for features like retrying page faults after
dropping the mm semaphore to break contention, or being
able to return from a stuck page fault when a SIGKILL is
pending.
This refactors our implementation of do_page_fault() to
move the error handling out of line in a way similar to
x86 and adds support for those two features.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we get a floating point, altivec or vsx unavaible interrupt in
kernel, we trigger a kernel error. There is no point preserving
the interrupt state, in fact, that can even make debugging harder
as the processor state might change (we may even preempt) between
taking the exception and landing in a debugger.
So just make those 3 disable interrupts unconditionally.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2: On BookE only disable when hitting the kernel unavailable
path, otherwise it will fail to restore softe as
fast_exception_return doesn't do it.
We currently turn interrupts back to their previous state before
calling do_page_fault(). This can be annoying when debugging as
a bad fault will potentially have lost some processor state before
getting into the debugger.
We also end up calling some generic code with interrupts enabled
such as notify_page_fault() with interrupts enabled, which could
be unexpected.
This changes our code to behave more like other architectures,
and make the assembly entry code call into do_page_faults() with
interrupts disabled. They are conditionally re-enabled from
within do_page_fault() in the same spot x86 does it.
While there, add the might_sleep() test in the case of a successful
trylock of the mmap semaphore, again like x86.
Also fix a bug in the existing assembly where r12 (_MSR) could get
clobbered by C calls (the DTL accounting in the exception common
macro and DISABLE_INTS) in some cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2. Add the r12 clobber fix
Some exceptions would unconditionally disable interrupts on entry,
which is fine, but calling lockdep every time not only adds more
overhead than strictly needed, but also means we get quite a few
"redudant" disable logged, which makes it hard to spot the really
bad ones.
So instead, split the macro used by the exception code into a
normal one and a separate one used when CONFIG_TRACE_IRQFLAGS is
enabled, and make the later skip th tracing if interrupts were
already disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We unconditionally hard enable interrupts. This is unnecessary as
syscalls are expected to always be called with interrupts enabled.
While at it, we add a WARN_ON if that is not the case and
CONFIG_TRACE_IRQFLAGS is enabled (we don't want to add overhead
to the fast path when this is not set though).
Thus let's remove the enabling (and associated irq tracing) from
the syscall entry path. Also on Book3S, replace a few mfmsr
instructions with loads of PACAMSR from the PACA, which should be
faster & schedule better.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the inlines into system.h and changes the runlatch
code to use the thread local flags (non-atomic) rather than
the TIF flags (atomic) to keep track of the latch state.
The code to turn it back on in an asynchronous interrupt is
now simplified and partially inlined.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The perfmon interrupt is the sole user of a special variant of the
interrupt prolog which differs from the one used by external and timer
interrupts in that it saves the non-volatile GPRs and doesn't turn the
runlatch on.
The former is unnecessary and the later is arguably incorrect, so
let's clean that up by using the same prolog. While at it we rename
that prolog to use the _ASYNC prefix.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes the various bits of assembly in the kernel entry,
exception handling and SLB management code that were specific
to running under the legacy iSeries hypervisor which is no
longer supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This cleans up vio.c after the removal of the legacy iSeries platform.
It also removes some no longer referenced include files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of digging a tty out of the tty_driver struct, which is not
defined to work, use tty_port properly. This includes proper tty
refcounting even though there is no possible race currently. But we
will need tty_port for tty buffers in the future anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timer is initialized too late. tty->open may fire an invalid
timer. So initialize the timer earlier using DEFINE_TIMER.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty->count test in the timer was racy. Let's remove the test and
properly delete the timer and wait for the body to finish using _sync
version of del_timer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* remove pointless checks (tty cannot be NULL at that points)
* fix some printks (use __func__, print text directly w/o using global
strings)
* remove some empty lines
This is the last patch for simserial. Overall, the driver is 400 lines
shorter. Being now at 560 lines.
It was tested using ski with a busybox userspace.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code to conform to the standard. Also make it readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Or the obsolete ones like:
"Let's have a little bit of fun"
I have never had fun with software. For fun, one needs hard-ware.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert shutdown to be tty_port_operations->shutdown. Then we can use
tty_port_hangup. (And we have to use tty_port_close.)
This means we no longer touch ASYNC_INITIALIZED, TTY_IO_ERROR. Also we
do not need to do any peculiar TTY logic in the file now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now we convert startup to be ->activate of tty_port. This means we
no longer care about INITIALIZED and TTY_IO_ERROR flags.
After we have ->activate much of the code may go as it duplicates what
tty_port_open does. In this case tty_port_open adds block_til_ready to
the path. But we do not define carrier hooks, so it is a noop.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So that we will not be surprised in the ISR anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I.e. remove more copied bloat.
The only change is that we wait_until_sent now. Which is what we
really should do.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code is identical except locking. But added locks to protect
counts do not hurt here. Rather the contrary.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All ->start, ->stop and ->wait_until_sent are empty and need not be
defined. The time to remove them is now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use it to make the code more readable.
Since tport doesn't conflict with port anymore and there are not many
tport accessors left, do also s/\<tport\>/port/g.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's do a spin-off of serial_state structure with only needed
elements.
And remove serialP crap from includes.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* instead of line, use tty->index or an iterator
* icount is not made public, only the tx path increments it
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not use any of the preinitialized rs_state members for something
real. So there is no need to initialize them. At the places we used
them for printing, just print the values.
And since only one port is supported, get rid of the loop. This
simplifies simrs_init a heap. Thus we can handle fail paths in a
standard way without panicing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes flags' type to ulong which is appropriate for all the
set/clear_bits performed in the drivers..
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing special. Just remove count from serial_state and change all
users to use tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note that previously simserial set the delay to 0. So we preserve
that. BUT, is it correct?
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tty_port to serial_state and start using common tty port members
from tty_port in amiserial and simserial. The rest will follow one by
one.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids pain with tty refcounting and touching tty_port in the
future. It allows us to remove some state->tty tests because the tty
passed down to them can never be NULL.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the final step to get rid of the one of the structures. A
further cleanup will follow. And I struct serial_state deserves cease
to exist after a switch to tty_port too.
While changing the lines, it removes also pointless tty->driver_data
casts.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not set ASYNC_SHARE_IRQ anywhere. And since IRQF_DISABLED is a
noop, pass zero to request_irq directly instead of this ugly macro.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It never worked there. The ISR was never written for that kind of
stuff. So remove all that crap with a hash of linked lists and pass
the pointer directly to the ISR.
BTW this answers the question there:
* I don't know exactly why they don't use the dev_id opaque data
* pointer instead of this extra lookup table
-> Because they thought they will support more devices bound to a
single interrupt w/o IRQF_SHARED. They would need exactly the hash
there.
What I don't understand is rebinding of the interrupt in the shutdown
path. They perhaps meant to do just synchronize_irq? In any case, this
is all gone and free_irq there properly.
By removing the hash we save some bits (exactly NR_IRQS * 8 bytes of
.bss and over a kilo of .text):
before:
text data bss dec hex filename
19600 320 8227 28147 6df3 ../a/ia64/arch/ia64/hp/sim/simserial.o
after:
text data bss dec hex filename
18568 320 28 18916 49e4 ../a/ia64/arch/ia64/hp/sim/simserial.o
Note that a shared interrupt could not work too. request_irq requires
data parameter to be non-NULL. So the whole IRQ_T exercise was
pointless.
Finally, this helps us remove another two members of async_struct :).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means:
* close_delay
* closing_wait
* line
* port
* xmit_fifo_size
This actually fixes a bug in amiserial. It initializes one and uses
the other of the close delays. Yes, duplicating structure members is
evil.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as for amiserial. Use only one instance of the flags.
Also remove them from async_struct now. Nobody else uses them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, the code succeeds when the port is opened by root and we
get unwanted interrupts storm on the first key stroke.
Instead of that, tell the user we failed and that we won't continue. I
suppose, the code was copied from the serial layer where we may want
to change the irq number, so we must allow open even of the failing
port. This is not the case for this driver at all.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when assign_irq_vector is called and the irq connected in
the simulator, the irq is not ready. request_irq will return ENOSYS
immediately. It is because the irq chip is unset.
Hence set the chip properly to irq_type_hp_sim. And make sure this is
done from both users of simulated interrupts.
Also we have to set handler here, otherwise we end up in
handle_bad_int resulting in spam in logs and no irqs handled. We use
handle_simple_irq as these are SW interrupts that need no ACK or
anything.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And remove declarations which are already in the headers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch-cases of SAL_FREQ_BASE generate non-relocatable code. The
same as for the ifs one level upper. This causes oopses early in boot
because the kernel jumps to the hell instead of the offset in sal
callback.
So use ifs here for SAL_FREQ_BASE decision too.
Isn't there any compiler directive or settings to solve that cleanly?
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_wakeup is safe to be called from all contexts. No need to schedule
a tasklet for that. Let's call it directly like in other drivers.
This allows us to kill another member of async_struct structure. (If
we remove the dummy uses in simserial.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, remove unused macro and rs_multiport_struct structure. Nobody
uses them at all.
Further, the 2 drivers (they are below) which use the rest of
structures from serialP.h (async_struct and serial_state) do not use
all the members. Remove the members:
* which are unused or
* which are only initialized and never used for something real.
Everybody should avoid the structures with a looong distance.
Finally, remove the ALPHA kludge MCR quirks. They are 1:1 copy from
8250.h. No need to redefine them here.
The 2 promised users of the structures:
arch/ia64/hp/sim/simserial.c
drivers/tty/amiserial.c
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All of them do not use the ugly interface defined in that header.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though the port is not used for anything real there yet, this
will change as tty buffers will be in tty_port in the near future. So
the port will be needed in all drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the timer ticks while we are holding the spinlock, the system
deadlocks. It is due to synchronous del_timer.
So to fix that, use spinlocks that properly disable bottom halves.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking if tty->index is in bounds is not needed. The tty has the
index set in the initial open. This is done in get_tty_driver. And it
can be only in interval <0,driver->num).
So remove the tests which check exactly this interval. Some are
left untouched as they check against the current backing device count.
(Leaving apart that the check is racy in most of the cases.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed because the tty buffer will become a tty_port member
later. That will help us to wipe out most of the races and checks for
the tty pointer in hot paths.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test and the assignment were racy. Make it really a singleton.
This is achieved by one global variable initialized at the module
init.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It makes the code more readable. We move the setup to the allocation
location because we need to initialize timers only once.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed following:
arch/arm/mach-s3c2440/s3c244x.c: In function 's3c244x_restart':
arch/arm/mach-s3c2440/s3c244x.c:209: error: expected declaration or statement at end of input
make[1]: *** [arch/arm/mach-s3c24xx/s3c244x.o] Error 1
make: *** [arch/arm/mach-s3c24xx] Error 2
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
While for a user mode register dump it may be reasonable to skip
those (albeit x86-64 doesn't do so), for kernel mode dumps these
should be printed to make sure all information possibly
necessary for analysis is available.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/4F58889202000078000770E7@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Building in support for either of these CPUs is pointless when
e.g. M686 was selected (since such a kernel would use cmov
instructions, which aren't available on these older CPUs).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/4F58875A02000078000770E0@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pull ARM updates from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7358/1: perf: add PMU hotplug notifier
ARM: 7357/1: perf: fix overflow handling for xscale2 PMUs
ARM: 7356/1: perf: check that we have an event in the PMU IRQ handlers
ARM: 7355/1: perf: clear overflow flag when disabling counter on ARMv7 PMU
ARM: 7354/1: perf: limit sample_period to half max_period in non-sampling mode
ARM: ecard: ensure fake vma vm_flags is setup
ARM: 7346/1: errata: fix PL310 erratum #753970 workaround selection
ARM: 7345/1: errata: update workaround for A9 erratum #743622
ARM: 7348/1: arm/spear600: fix one-shot timer
ARM: 7339/1: amba/serial.h: Include types.h for resolving dependency of type bool
There was a latent typo in the C6X KSTK_EIP and KSTK_ESP macros which
caused a problem with a new patch which used them. The broken definitions
were of the form:
#define KSTK_FOO(tsk) (task_pt_regs(task)->foo)
Note the use of task vs tsk. This actually worked before because the
only place in the kernel which used these macros passed in a local
pointer named task.
Signed-off-by: Mark Salter <msalter@redhat.com>
When a CPU is taken out of reset, either cold booted or hotplugged in,
some of its PMU registers can contain UNKNOWN values.
This patch adds a hotplug notifier to ARM core perf code so that upon
CPU restart the PMU unit is reset and becomes ready to use again.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
xscale2 PMUs indicate overflow not via the PMU control register, but by
a separate overflow FLAG register instead.
This patch fixes the xscale2 PMU code to use this register to detect
to overflow and ensures that we clear any pending overflow when
disabling a counter.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PMU IRQ handlers in perf assume that if a counter has overflowed
then perf must be responsible. In the paranoid world of crazy hardware,
this could be false, so check that we do have a valid event before
attempting to dereference NULL in the interrupt path.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When disabling a counter on an ARMv7 PMU, we should also clear the
overflow flag in case an overflow occurred whilst stopping the counter.
This prevents a spurious overflow being picked up later and leading to
either false accounting or a NULL dereference.
Cc: <stable@vger.kernel.org>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ARM, the PMU does not stop counting after an overflow and therefore
IRQ latency affects the new counter value read by the kernel. This is
significant for non-sampling runs where it is possible for the new value
to overtake the previous one, causing the delta to be out by up to
max_period events.
Commit a737823d ("ARM: 6835/1: perf: ensure overflows aren't missed due
to IRQ latency") attempted to fix this problem by allowing interrupt
handlers to pass an overflow flag to the event update function, causing
the overflow calculation to assume that the counter passed through zero
when going from prev to new. Unfortunately, this doesn't work when
overflow occurs on the perf_task_tick path because we have the flag
cleared and end up computing a large negative delta.
This patch removes the overflow flag from armpmu_event_update and
instead limits the sample_period to half of the max_period for
non-sampling profiling runs.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The board file uses a 4CC defined in linux/videodev2.h. Include the
header to fix
arch/arm/mach-shmobile/board-ag5evm.c:262: error: 'V4L2_PIX_FMT_RGB565'
undeclared here (not in a function)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
arch/arm/mach-shmobile/board-bonito.c:244:3: error: unknown field 'bpp' specified in initializer
make[2]: *** [arch/arm/mach-shmobile/board-bonito.o] Error 1
caused by commit "fbdev: sh_mobile_lcdc: Support FOURCC-based format API"
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the SH7785 code misdefines the UBC clock connection ID in
relation to the other CPUs. This makes it uniform, so that things like
single-stepping work again.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- Use memchr_inv to check if the data contains all 0xFF bytes.
It is faster than looping for each byte.
- Use memcmp to compare memory areas
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All IRQs on powerpc are managed via irq_domain anyway, there isn't really
any advantage to turning SPARSE_IRQ off, and it's the direction we want
to take the kernel design anyway. This patch makes powerpc always use
SPARSE_IRQ.
On pseries_defconfig, SPARSE_IRQ adds only about 0x300 bytes to the
.text sections, and removes about 0x20000 from the data section for the
static irq_desc table.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a 16TB system (using AMS/CMO), I get:
WARNING: ignoring large property [/ibm,dynamic-reconfiguration-memory] ibm,dynamic-memory length 0x000000000017ffec
and significantly less memory is thus shown to the partition. As far as
I can tell, the constant used is arbitrary. Ben Herrenschmidt provided
additional background that
> The limit was originally set because of Apple machines carrying ROM
> images in the device-tree, at a time where we were much more memory
> constrained than we are now.
and that it is likely not very useful any longer.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Emit the function name not the address when possible.
builtin_return_address() gives an address. When building
a kernel with CONFIG_KALLSYMS, emit the actual function
name not the address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a race where a thread causes a coprocessor type to be valid
in its own ACOP _and_ in the current context, but it does not
propagate to the ACOP register of other threads in time for them to
use it. The original code tries to solve this by sending an IPI to
all threads on the system, which is heavy handed, but unfortunately
still provides a window where the icswx is issued by other threads and
the ACOP is not up to date.
This patch detects that the ACOP DSI fault was a "false positive" and
syncs the ACOP and causes the icswx to be replayed.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement atomic_inc_not_zero and atomic64_inc_not_zero. At the
moment we use atomic*_add_unless which requires us to put 0 and
1 constants into registers. We can also avoid a subtract by
saving the original value in a second temporary.
This removes 3 instructions from fget:
- c0000000001b63c0: 39 00 00 00 li r8,0
- c0000000001b63c4: 39 40 00 01 li r10,1
...
- c0000000001b63e8: 7c 0a 00 50 subf r0,r10,r0
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It turns out that test-compiling this file on x86-64 doesn't really
help, because much of it is x86-32-specific. And so I hadn't noticed
the slightly over-eager removal of the 'r' from 'addr' variable despite
thinking I had tested it.
Signed-off-by: Linus "oopsie" Torvalds <torvalds@linux-foundation.org>
Several users of "find_vma_prev()" were not in fact interested in the
previous vma if there was no primary vma to be found either. And in
those cases, we're much better off just using the regular "find_vma()",
and then "prev" can be looked up by just checking vma->vm_prev.
The find_vma_prev() semantics are fairly subtle (see Mikulas' recent
commit 83cd904d27: "mm: fix find_vma_prev"), and the whole "return
prev by reference" means that it generates worse code too.
Thus this "let's avoid using this inconvenient and clearly too subtle
interface when we don't really have to" patch.
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This compatible value will be used to distinguish some special features of APM821XX EMAC: no half duplex mode support, configuring jumbo frame.
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fixes' of git://github.com/hzhuang1/linux: (3 commits)
ARM: pxa: fix invalid mfp pin issue
ARM: pxa: remove duplicated registeration on pxa-gpio
ARM: pxa: add dummy clock for pxa25x and pxa27x
Includes an update to v3.3-rc6
As done for the other ep93xx machines in:
commit 9a6879bd90
ARM: ep93xx: convert to MULTI_IRQ_HANDLER
Now that there is a generic IRQ handler for multiple VIC devices use it
for vision_ep9307 to help building multi platform kernels.
Signed-off-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0lYr
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
A few more ASoC updates, the main one is the move of the audmux driver
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
This patch adds s3c_fb_driverdata s3c_fb_data_exynos5 for EXYNOS5
and adds extended timing control setting.
EXYNOS5 FIMD needs extended setting for video timing control.
Additional bits are added to VIDTCON2, VIDWxxADD2, VIDOSDxA and
VIDOSDxB registers in order to set timing value for lager resolution.
Also, address offset of VIDTCONx registers is changed from 0x0
to 0x20000, thus variable type should be changed to int type
to handle the address offset of VIDTCONx registers for EXYNOS5 FIMD.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This causes the Tegra pinctrl driver to be built whenever core Tegra
support is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra pinmux, and required parameterization
data for Tegra20 and Tegra30.
The driver is initially added with driver name and device tree compatible
value that won't cause this driver to be used. A later change will switch
the pinctrl driver to use the correct values, switch the old pinmux
driver to be disabled, and update all code that uses the old pinmux APIs
to use the new pinctrl APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
[squashed "fix case of Tegra30's foo_groups[] arrays"]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenRISC does not have global memory_start and memory_end
symbols.
The prototypes are in vain.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Things break rather ungracefully when a semicolon gets substituted into
an expression... discovered while build-testing linux-next for 3.4
Signed-off-by: Jonas Bonn <jonas@southpole.se>
The pt_regs struct had both a 'syscallno' field and an 'orig_gpr11' field
and it wasn't really clear how these were supposed to be used. This patch
removes the syscallno field altogether and makes orig_gpr11 work more
like other architectures: keep track of syscall number in progress or
hold -1 for non-syscall exceptions.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
virt_addr_valid() shouldn't be comparing the address to memory_end which is
a phys_addr_t. Change this to do like other arches and check that the
address falls within a valid page frame.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
dump_stack() is used by modules and needs to be exported.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
To have atomit64_t on OpenRISC we need GENERIC_ATOMIC64.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Like most systems, OLPC's ACPI LID switch wakes up the system
when the lid is opened, but not when it is closed.
Under OLPC's opportunistic suspend model, the lid may be closed
while the system was oportunistically suspended with the screen
running. In this event, we want to wake up to turn the screen
off.
Enable control of normal ACPI wakeups through lid close events
through a new sysfs attribute "lid_wake_on_closed". When set,
and when LID wakeups are enabled through ACPI, the system will
wake up on both open and close lid events.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
[ Fixed sscanf checking]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-bgt8hxu2wwe0x5p8edhogtf7@git.kernel.org
[ Did very minor readability tweaks ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a bug in kprobes which can modify kernel code
permanently at run-time. In the result, kernel can
crash when it executes the modified code.
This bug can happen when we put two probes enough near
and the first probe is optimized. When the second probe
is set up, it copies a byte which is already modified
by the first probe, and executes it when the probe is hit.
Even worse, the first probe and the second probe are removed
respectively, the second probe writes back the copied
(modified) instruction.
To fix this bug, kprobes always recovers the original
code and copies the first byte from recovered instruction.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: systemtap@sourceware.org
Cc: anderson@redhat.com
Link: http://lkml.kernel.org/r/20120305133215.5982.31991.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Current probed-instruction recovery expects that only breakpoint
instruction modifies instruction. However, since kprobes jump
optimization can replace original instructions with a jump,
that expectation is not enough. And it may cause instruction
decoding failure on the function where an optimized probe
already exists.
This bug can reproduce easily as below:
1) find a target function address (any kprobe-able function is OK)
$ grep __secure_computing /proc/kallsyms
ffffffff810c19d0 T __secure_computing
2) decode the function
$ objdump -d vmlinux --start-address=0xffffffff810c19d0 --stop-address=0xffffffff810c19eb
vmlinux: file format elf64-x86-64
Disassembly of section .text:
ffffffff810c19d0 <__secure_computing>:
ffffffff810c19d0: 55 push %rbp
ffffffff810c19d1: 48 89 e5 mov %rsp,%rbp
ffffffff810c19d4: e8 67 8f 72 00 callq
ffffffff817ea940 <mcount>
ffffffff810c19d9: 65 48 8b 04 25 40 b8 mov %gs:0xb840,%rax
ffffffff810c19e0: 00 00
ffffffff810c19e2: 83 b8 88 05 00 00 01 cmpl $0x1,0x588(%rax)
ffffffff810c19e9: 74 05 je ffffffff810c19f0 <__secure_computing+0x20>
3) put a kprobe-event at an optimize-able place, where no
call/jump places within the 5 bytes.
$ su -
# cd /sys/kernel/debug/tracing
# echo p __secure_computing+0x9 > kprobe_events
4) enable it and check it is optimized.
# echo 1 > events/kprobes/p___secure_computing_9/enable
# cat ../kprobes/list
ffffffff810c19d9 k __secure_computing+0x9 [OPTIMIZED]
5) put another kprobe on an instruction after previous probe in
the same function.
# echo p __secure_computing+0x12 >> kprobe_events
bash: echo: write error: Invalid argument
# dmesg | tail -n 1
[ 1666.500016] Probing address(0xffffffff810c19e2) is not an instruction boundary.
6) however, if the kprobes optimization is disabled, it works.
# echo 0 > /proc/sys/debug/kprobes-optimization
# cat ../kprobes/list
ffffffff810c19d9 k __secure_computing+0x9
# echo p __secure_computing+0x12 >> kprobe_events
(no error)
This is because kprobes doesn't recover the instruction
which is overwritten with a relative jump by another kprobe
when finding instruction boundary.
It only recovers the breakpoint instruction.
This patch fixes kprobes to recover such instructions.
With this fix:
# echo p __secure_computing+0x9 > kprobe_events
# echo 1 > events/kprobes/p___secure_computing_9/enable
# cat ../kprobes/list
ffffffff810c1aa9 k __secure_computing+0x9 [OPTIMIZED]
# echo p __secure_computing+0x12 >> kprobe_events
# cat ../kprobes/list
ffffffff810c1aa9 k __secure_computing+0x9 [OPTIMIZED]
ffffffff810c1ab2 k __secure_computing+0x12 [DISABLED]
Changes in v4:
- Fix a bug to ensure optimized probe is really optimized
by jump.
- Remove kprobe_optready() dependency.
- Cleanup code for preparing optprobe separation.
Changes in v3:
- Fix a build error when CONFIG_OPTPROBE=n. (Thanks, Ingo!)
To fix the error, split optprobe instruction recovering
path from kprobes path.
- Cleanup comments/styles.
Changes in v2:
- Fix a bug to recover original instruction address in
RIP-relative instruction fixup.
- Moved on tip/master.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: systemtap@sourceware.org
Cc: anderson@redhat.com
Link: http://lkml.kernel.org/r/20120305133209.5982.36568.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add platform driver for the Soekris Engineering net5501 single-board
computer. Probes well-known locations in ROM for BIOS signature
to confirm correct platform. Registers 1 LED and 1 GPIO-based
button (typically used for soft reset).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
[ Removed Kconfig and Makefile detritus from drivers/leds/]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-jv5uf34996juqh5syes8mn4h@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
GPIO 24 is used in reference designs as a soft-reset button, and
the alix2 is no exception. Add it as a gpio-button.
Use symbolic values to describe BIOS addresses.
Record the model number.
Signed-off-by: Philip A. Prindeville <philipp@redfish-solutions.com>
Acked-by: Ed Wildgoose <kernel@wildgooses.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-sjp6k1rjksitx1pej0c0qxd1@git.kernel.org
[ tidied up the code a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Failure is reported on hx4700 with kernel v3.3-rc1.
__mfp_validate: GPIO20 is invalid pin
__mfp_validate: GPIO21 is invalid pin
__mfp_validate: GPIO15 is invalid pin
__mfp_validate: GPIO78 is invalid pin
__mfp_validate: GPIO79 is invalid pin
__mfp_validate: GPIO80 is invalid pin
__mfp_validate: GPIO33 is invalid pin
__mfp_validate: GPIO48 is invalid pin
__mfp_validate: GPIO49 is invalid pin
__mfp_validate: GPIO50 is invalid pin
Since pxa_last_gpio is used in mfp-pxa2xx driver. But it's only
updated in pxa-gpio driver that run after mfp-pxa2xx driver.
So update the pxa_last_gpio first in mfp-pxa2xx driver.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Both reboot (via reboot(RB_AUTOBOOT)) and suspend freeze on hx4700.
Registration of pxa_gpio_syscore_ops is moved into pxa-gpio driver,
but it still exists in arch-pxa directory. It resulsts failure on
reboot and suspend.
Now remove the registration code in arch-pxa.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
This regression was introduced by the commit "ARM: pxa: add dummy
clock for sa1100-rtc", id a55b5adaf4.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
As audmux becomes a platform driver and its callers are all ASoC
machine drivers, there is no reason to keep it in arch folder, so
move it to sound/soc/imx.
One bonus point would be those ASoC machine drivers stop including
mach/audmux.h, since it's been moved to sound/soc/imx/imx-audmux.h.
This should be a move to the right direction in terms of single kernel
image goal.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It coverts audmux to a platform driver, so that it can be moved into
sound/soc/imx and adopt device tree support later.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It merges audmux-v1 and audmux-v2 under arch/arm/plat-mxc into one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It moves phycore audmux configuration call from board file into ASoC
machine driver phycore-ac97 to ease converting audmux into a platform
driver later.
It moves phycore audmux configuration call from board file into ASoC
machine driver phycore-ac97, so that it gets aligned with wm1133-ev1
and mx27vis-aic32x4, and more importantly it will ease the moving of
audmux into sound/soc/imx as a platform driver later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It moves eukrea audmux configuration call from board file into ASoC
machine driver eukrea-tlv320, so that it gets aligned wm1133-ev1 and
mx27vis-aic32x4, and more importantly it will ease the moving of audmux
into sound/soc/imx as a platform driver later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge the emailed seties of 19 patches from Andrew Morton
* akpm:
rapidio/tsi721: fix queue wrapping bug in inbound doorbell handler
memcg: fix mapcount check in move charge code for anonymous page
mm: thp: fix BUG on mm->nr_ptes
alpha: fix 32/64-bit bug in futex support
memcg: fix GPF when cgroup removal races with last exit
debugobjects: Fix selftest for static warnings
floppy/scsi: fix setting of BIO flags
memcg: fix deadlock by inverting lrucare nesting
drivers/rtc/rtc-r9701.c: fix crash in r9701_remove()
c2port: class_create() returns an ERR_PTR
pps: class_create() returns an ERR_PTR, not NULL
hung_task: fix the broken rcu_lock_break() logic
vfork: kill PF_STARTING
coredump_wait: don't call complete_vfork_done()
vfork: make it killable
vfork: introduce complete_vfork_done()
aio: wake up waiters when freeing unused kiocbs
kprobes: return proper error code from register_kprobe()
kmsg_dump: don't run on non-error paths by default
Michael Cree said:
: : I have noticed some user space problems (pulseaudio crashes in pthread
: : code, glibc/nptl test suite failures, java compiler freezes on SMP alpha
: : systems) that arise when using a 2.6.39 or later kernel on Alpha.
: : Bisecting between 2.6.38 and 2.6.39 (using glibc/nptl test suite as
: : criterion for good/bad kernel) eventually leads to:
: :
: : 8d7718aa08 is the first bad commit
: : commit 8d7718aa08
: : Author: Michel Lespinasse <walken@google.com>
: : Date: Thu Mar 10 18:50:58 2011 -0800
: :
: : futex: Sanitize futex ops argument types
: :
: : Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
: : prototypes to use u32 types for the futex as this is the data type the
: : futex core code uses all over the place.
: :
: : Looking at the commit I see there is a change of the uaddr argument in
: : the Alpha architecture specific code for futexes from int to u32, but I
: : don't see why this should cause a problem.
Richard Henderson said:
: futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
: u32 oldval, u32 newval)
: ...
: : "r"(uaddr), "r"((long)oldval), "r"(newval)
:
:
: There is no 32-bit compare instruction. These are implemented by
: consistently extending the values to a 64-bit type. Since the
: load instruction sign-extends, we want to sign-extend the other
: quantity as well (despite the fact it's logically unsigned).
:
: So:
:
: - : "r"(uaddr), "r"((long)oldval), "r"(newval)
: + : "r"(uaddr), "r"((long)(int)oldval), "r"(newval)
:
: should do the trick.
Michael said:
: This fixes the glibc test suite failures and the pulseaudio related
: crashes, but it does not fix the java compiiler lockups that I was (and
: are still) observing. That is some other problem.
Reported-by: Michael Cree <mcree@orcon.net.nz>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Michel Lespinasse <walken@google.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Our TLB ops want to check the vma vm_flags to find out whether the
mapping is executable. However, we leave this uninitialized in
ecard.c. Initialize it with an appropriate value.
Reported-by: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull PCI fixes from Jesse Barnes:
"A couple of fixes for booting specific machines, and one for a minor
memory leak on pre-_CRS platforms."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
x86/PCI: do not tie MSI MS-7253 use_crs quirk to BIOS version
x86/PCI: use host bridge _CRS info on MSI MS-7253
PCI: fix memleak when ACPI _CRS is not used.
