error_bo and pinned_bo could be used uninitialised if there were no
active buffers.
Caught by kmemcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The opregion is a shared memory region between ACPI and the graphics
driver. As the ACPI mapping has been changed to cachable in commit
6d5bbf00d2, mapping the intel opregion
non-cachable now fails. As no bus-master hardware is involved in the
opregion, cachable map should do no harm.
Tested on a Fujitsu Lifebook P8010.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
[ickle: convert to acpi_os_ioremap for consistency]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Merge with Linus to resolve conflicting fixes for the reusing the stale
HEAD value during intel_ring_wait().
Conflicts:
drivers/gpu/drm/i915/intel_ringbuffer.c
If the driver calls into the kernel to wait for a breadcrumb to pass,
but hasn't enabled interrupts, fallback to polling the breadcrumb value.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only have sufficient information for accurate (sub-frame) timestamping
when the modesetting is under our control.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can only utilize the stolen portion of the GTT if we are in sole
charge of the hardware. This is only true if using GEM and KMS,
otherwise VESA continues to access stolen memory.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Don't reset if the engine isn't busy. This matches the behavior of
previous asics. Reseting a non-hung block can lead to a hang.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33272
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Seems some other boards do this as well.
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
I'm amazed but not really surprised this worked on x86...
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Starting with SandyBridge (though possible with earlier hacked BIOSes),
the BIOS may initialise the IGFX as secondary to a discrete GPU. Prior,
it would simply disable the integrated GPU. So we adjust our PCI class
mask to match any DISPLAY_CLASS device.
In such a configuration, the IGFX is not a primary VGA controller and
so should not take part in VGA arbitration, and the error return from
vga_client_register() is expected.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
There are I915_NUM_RINGS-1 inter-ring synchronisation counters, but we
were clearing I915_NUM_RINGS of them. Oops.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During system suspend, the "wait for ring buffer to empty" loop would
always time out after three seconds, because the faster cached ring
buffer head read would always return zero. Force the slow-and-careful
PIO read on all but the first iterations of the loop to fix it.
This also removes the unused (and useless) 'actual_head' variable that
tried to approximate doing this, but did it incorrectly.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: DRI mailing list <dri-devel@lists.freedesktop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During suspend, Linus found that his machine would hang for 3 seconds,
and identified that intel_ring_buffer_wait() was the culprit:
"Because from looking at the code, I get the notion that
"intel_read_status_page()" may not be exact. But what happens if that
inexact value matches our cached ring->actual_head, so we never even
try to read the exact case? Does it _stay_ inexact for arbitrarily
long times? If so, we might wait for the ring to empty forever (well,
until the timeout - the behavior I see), even though the ring really
_is_ empty."
As the reported HEAD position is only updated every time it crosses a
64k boundary, whilst draining the ring it is indeed likely to remain one
value. If that value matches the last known HEAD position, we never read
the true value from the register and so trigger a timeout.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Hangcheck and error recovery is only used by GEM.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Without this change, blits to the front buffer won't invalidate FBC
state, causing us to scan out stale data. Make sure we update these
bits on every FBC enable, since they may get clobbered if we shut off
the display.
References: https://bugzilla.kernel.org/show_bug.cgi?id=26932
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a couple of missing workaround bits for ILK & SNB. These disable
clock gating on a couple of units that would otherwise prevent FBC from
working.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
First, we were calling mc_stop() at the top of the function
which turns off all MC (memory controller) clients,
then checking if the GPU is idle. If it was idle we
returned without re-enabling the MC clients which would
lead to a blank screen, etc. This patch checks if the
GPU is idle before calling mc_stop().
Second, if the reset failed, we were returning without
re-enabling the MC clients. This patch re-enables
the MC clients before returning regardless of whether
the reset was successful or not.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching to pcie gen2 causes problems on some
boards. Add a module option to turn it on/off.
There are gen2 compatability issues with some
motherboards it seems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33027
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix gpu page faults triggered by plymouthd
drm/nouveau: greatly simplify mm, killing some bugs in the process
drm/nvc0: enable protection of system-use-only structures in vm
drm/nv40: initialise 0x17xx on all chipsets that have it
drm/nv40: make detection of 0x4097-ful chipsets available everywhere
The switch to separate BAR and channel address spaces made the fbcon memory
address calculation incorrect on NV50+ boards, this commit fixes that.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This reverts commit dfe63bb0ad.
This commit was causing nouveau not to work properly, for -rc1 I'd
prefer it worked and we can look if this is useful for 2.6.39.
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915/lvds: Add AOpen i915GMm-HFS to the list of false-positive LVDS
agp/intel: Fix device names of i845 and 845G
drm/i915: Disable GPU semaphores on SandyBridge mobile
drm/i915/execbuffer: Clear domains before beginning reloc processing
drm/i915/execbuffer: Reorder relocations to match new object order
drm/i915: Fix error handler to capture the first batch after the seqno
drm/i915: Add a module option to override the use of SSC
drm/i915/panel: The backlight is enabled if the current value is non-zero
drm/i915/debugfs: Correct format after changing type of err object 'size'
Hopefully, this is a temporary measure whilst the root cause is
understood. At the moment, we experience a hard hang whilst looping
urbanterror that has been identified as a result of the use of
semaphores, but so far only on SNB mobile.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32752
Tested-by: mengmeng.meng@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (59 commits)
ACPI / PM: Fix build problems for !CONFIG_ACPI related to NVS rework
ACPI: fix resource check message
ACPI / Battery: Update information on info notification and resume
ACPI: Drop device flag wake_capable
ACPI: Always check if _PRW is present before trying to evaluate it
ACPI / PM: Check status of power resources under mutexes
ACPI / PM: Rename acpi_power_off_device()
ACPI / PM: Drop acpi_power_nocheck
ACPI / PM: Drop acpi_bus_get_power()
Platform / x86: Make fujitsu_laptop use acpi_bus_update_power()
ACPI / Fan: Rework the handling of power resources
ACPI / PM: Register power resource devices as soon as they are needed
ACPI / PM: Register acpi_power_driver early
ACPI / PM: Add function for updating device power state consistently
ACPI / PM: Add function for device power state initialization
ACPI / PM: Introduce __acpi_bus_get_power()
ACPI / PM: Introduce function for refcounting device power resources
ACPI / PM: Add functions for manipulating lists of power resources
ACPI / PM: Prevent acpi_power_get_inferred_state() from making changes
ACPICA: Update version to 20101209
...
After reordering the sequence of relocating objects, commit 6fe4f1404,
we can no longer rely on seeing all reloc targets prior to performing
the relocation. As a result we were ignoring the need to flush objects
from the render cache and invalidate the sampler caches, resulting in
rendering glitches. So we need to clear the relocation domains earlier.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On the fault path, commit 6fe4f140 introduction a regression whereby it
changed the sequence of the objects but continued to use the original
ordering of relocation entries. The result was that incorrect GTT offsets
were being fed into the execbuffer causing lots of misrendering and
potential hangs.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst we had no older batches on the active list, everything was fine.
However, if the GPU is free running and the requests are only being
reaped by the periodic retirer, than the current seqno may not be at the
start of the list. In this case we need to select the first batch after
the last seqno written by the gpu and not inclusive of the seqno.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to workaround the issue with LVDS not working on the Lenovo
U160 apparently due to using the wrong SSC frequency, add an option to
disable SSC.
Suggested-by: Lukács, Árpád <lukacs.arpad@gmail.com>
Bugzillla: https://bugs.freedesktop.org/show_bug.cgi?id=32748
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
... and not if the maximum is non-zero. This fixes the typo introduced
in 47356eb672 and preserves the backlight value from boot.
[ickle: My thanks also to Indan Zupancic for diagnosing the original
regression and suggesting the appropriate fix.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org # after 47356eb672
As the mappable portion of the aperture is always a small subset at the
start of the GTT, it is allocated preferentially by drm_mm. This is
useful in case we ever need to map an object later. However, if you have
a large object that can consume the entire mappable region of the
GTT this prevents the batchbuffer from fitting and so causing an error.
Instead allocate all those that require a mapping up front in order to
improve the likelihood of finding sufficient space to bind them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than evicting an object at random, which is unlikely to alleviate
the memory pressure sufficient to allow us to continue, zap the entire
aperture. That should give the system long enough to recover and reap
some pages from the evicted objects, forestalling the allocation error
for the new object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Before releasing the lock in order to copy the relocation list from user
pages, we need to drop all the object references as another thread may
usurp and execute another batchbuffer before we reacquire the lock.
However, the code was buggy and failed to clear the list...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
In order to retire active buffers whilst no client is active, we need to
insert our own flush requests onto the ring.
This is useful for servers that queue up some rendering and then go to
sleep as it allows us to the complete processing of those requests,
potentially making that memory available again much earlier.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dave Airlie spotted that his ILK laptop with DMAR enabled was generating
the occasional DMAR warning.
"The ordering in the previous code was to rewrite the GTT table before
unmapping the pages and that makes sense to me."
This is his stable patch ported to d-i-n.
Reported-by: Dave Airlie <airlied@redhat.com>
Original-patch-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The docs recommend that if 8 display lines fit inside the FIFO buffer,
then the number of watermark entries should be increased to hide the
latency of filling the rest of the FIFO buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI and the transcoders can fail for various reasons, so detect those
conditions and report on them.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cleanup several aspects of the rc6 code:
- misnamed intel_disable_clock_gating function (was only about rc6)
- remove commented call to intel_disable_clock_gating
- rc6 enabling code belongs in its own function (allows us to move the
actual clock gating enable call back into restore_state)
- allocate power & render contexts up front, only free on unload
(avoids ugly lazy init at rc6 enable time)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: checkpatch cleanup]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enabling RC6 implies setting a graphics context. Make sure we do that
only after the ring has been enabled, otherwise our ring commands will
hang.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Re-enable rc6 support on Ironlake for power savings. Adds a debugfs
file to check current RC state, adds a missing workaround for Ironlake
MI_SET_CONTEXT instructions, and renames MCHBAR_RENDER_STANDBY to
RSTDBYCTL to match the docs.
Keep RC6 and the power context disabled on pre-ILK. It only seems to
hang and doesn't save any power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As the IMR for the USER interrupts are not modified elsewhere, we can
separate the spinlock used for these from that of hpd and pipestats.
Those two IMR are manipulated under an IRQ and so need heavier locking.
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to ensure that writes through the GTT land before any
modification to the MMIO registers and so must impose a mandatory write
barrier when flushing the GTT domain. This was revealed by relaxing the
write ordering by experimentally mapping the registers and the GATT as
write-combining.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As has_gem is unconditionally set to true, the conditional immediately
following that assignment is superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These functions need to be reworked for Ironlake and above, but until
then at least avoid reading non-existent registers.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: combine with a gratuitous tidy]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When bringing up new hardware, or otherwise experimenting, GPU hangs are
a way of life. However, the automatic GPU reset can do more harm than
good under these circumstances, as we may wish to capture a full trace for
debugging.
Based on a patch by Zhenyu Wang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake, the LP0 latency is hardcoded and in ns unit, while on
Sandybridge, it comes from a register and with unit 0.1 us. So, fix
the wrong latency value while computing wm0 on Ironlake and Sandybridge.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch actually makes the watermark code even uglier (if that's
possible), but has the advantage of sharing code between SNB and ILK at
least. Longer term we should refactor the watermark stuff into its own
file and clean it up now that we know how it's supposed to work.
Supporting WM2 on my Vaio reduced power consumption by around 0.5W, so
this patch is definitely worthwhile (though it also needs lots of test
coverage).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: pass the watermark structs arounds]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On i830 if the tail pointer is set to within 2 cachelines of the end of
the buffer, the chip may hang. So instead if the tail were to land in
that location, we pad the end of the buffer with NOPs, and start again
at the beginning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In some configuration, the PCU may allow us to overclock the GPU.
Check for this case and adjust the max frequency as appropriate. Also
initialize the min/max frequencies to default values as indicated by
hardware.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... and just any combination of bits & ~PFIT_ENABLE. This way we do not
attempt disable to the panel fitter controller uselessly upon
intel_lvds_disable().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Alex Fiestas reported an issue with his HDMI connector being misdetected
as DVI unless he had something connected upon boot. By moving the
decision as to whether to use HDMI or DVI encoding for the HDMI capable
output until we probe the monitor means that we should avoid sending a
HDMI signal to a DVI monitor and also correctly detect hardware like
Alex's.
However, to really determine what connector is soldered onto the wire we
need to inspect the VBT sdvo child devices - but can we trust it?
Reported-by: Alex Fiestas <alex@eyeos.org>
Tested-by: Alex Fiestas <alex@eyeos.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32828
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Some voltage swing/pre-emphasis level use the same value on eDP
Sandybridge, like 400mv_0db and 600mv_0db are with the same value
of (0x0 << 22). So, fix them, and point out the value if it isn't
a supported voltage swing/pre-emphasis level.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Since Linux 2.6.36 the digital output on my system (855GME + DVI-I) is
not working any longer. The analog output is always activated
regardless of the type of monitor attached.
The culprit seems to be intel_crt_detect_ddc(), which returns true as
soon as an ACK from the EDID device is received. Obviously this
approach does not work with DVI-I where the analog and digital outputs
share a common DDC bus.
In a similar manner to the shared DDC wire, ala the "Mac Mini Hack", we
need an additional check to make sure that there really is an analog
device attached to the DDC.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
When trying to do channel equalization, we need to make sure we still
have clock recovery on all lanes while training. We also need to try
clock recovery again if we lose the clock or if channel eq fails 5
times. We'll try clock recovery up to 5 more times before giving up
entirely.
Gets suspend/resume working on my Vaio again and brings us back into
compliance with the DP training sequence spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were using a stale pointer in the check which caused us to use CPU
attached DP params when we should have been using PCH attached params.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31988
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Christoph Lukas <christoph.lukas@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (390 commits)
drm/radeon/kms: disable underscan by default
drm/radeon/kms: only enable hdmi features if the monitor supports audio
drm: Restore the old_fb upon modeset failure
drm/nouveau: fix hwmon device binding
radeon: consolidate asic-specific function decls for pre-r600
vga_switcheroo: comparing too few characters in strncmp()
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
...
Lots of HDMI TVs overscan the incoming image by default.
The underscan option was added as a way to compensate for
that by underscanning the image so that the edges would
not be cut off on an overscanning TV. However, the TV
provides no way of knowing whether it is overscanning or
not. If the user has disabled overscan on their TV or has a
TV that does not overscan, you will get black bars around the
edges of your screen. Prior to the patch we got complaints
and bug reports from users with overscanning TVs, now with
the patch, we get lots of complaints and bug reports from
users with non-overscanning TVs. There's no good default,
but on average there have been more users complaining about
it being on by default than off, so change it to off. This
will probably result in a new deluge of overscanning TV user
complaints. There's no winning.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This avoids some issues in the current hdmi audio code for monitors
without audio.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-ni' of ../drm-radeon-next: (30 commits)
radeon: consolidate asic-specific function decls for pre-r600
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
drm/radeon/kms: parse DCE5 encoder caps when setting up encoders
drm/radeon/kms: dvo dpms updates for DCE5
drm/radeon/kms: dac dpms updates for DCE5
drm/radeon/kms: DCE5 atom dig encoder updates
drm/radeon/kms: DCE5 atom transmitter control updates
...
* 'nouveau/drm-nouveau-next' of ../drm-nouveau-next:
drm/nouveau: fix hwmon device binding
drm/nouveau: create grctx on the fly on all chipsets
drm/nvc0: fix init without firmware present
drm/nvc0/pgraph: fix 0x406028/0x405870 init
drm/nvc0/pgraph: more unit names
drm/nvc0/pfifo: support for chipsets with only one PSUBFIFO (0xc1)
drm/nvc0: reserve only subc 0 for kernel use
drm/nv50: sync up gr data error names with rnn, use for nvc0 also
drm/nvc0: parse a couple more PGRAPH_INTR
drm/nvc0: nuke left-over debug messages
drm/nvc0: kill off a couple more magics
drm/nouveau: Validate channel indices passed from userspace.
drm/nouveau: Only select ACPI_VIDEO if its dependencies are met
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Bind the hwmon structs to nouveau device kobj. This makes sure
the hwmon files are created in the device subdir in line with
all other hwmon drivers.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Move them to radeon_asic.h together with the other asic
specific stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a copy-and-paste bug. We should be comparing 4 characters here
instead of 3.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vbios only partially initializes the memory controller on
NI, so now we need to load the MC ucode in the driver and set
the default clocks once the ucode is loaded.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MC ucode is no longer loaded by the vbios
tables as on previous asics. It now must be loaded
by the driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hardware supports advanced user defined color management
but at the moment, there is no infrastructure in place to take
advantage of it so for now we just support the legacy LUTs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds some new NI (northern islands) specific display
register defines.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NI chips no longer load the MC ucode in the asic_init sequence so
the asic comes up in a basic mode with low engine/memory clocks and
a voltage. Once the MC ucode is loaded by the driver the card
can be programmed to it's proper default clocks and voltage. As such
the default clocks in the firmware info table as the post clocks, not
the default running clocks. Track the default post clocks and default
running clocks separately to handle this.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems disable the vbios on secondary cards or cards that
have been posted. This code re-enabled the vbios so the driver
can load it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Needed to tell which DIG encoders are HBR2 capable for DP 1.2.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DVOOutputControl table was removed for DCE5.
DVOEncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DAC1OutputControl table was removed for DCE5.
DAC1EncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Supported on rv6xx/r7xx/evergreen. Cards come up in gen1 mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If you change the color depth via fbset or some other framebuffer aware
userland application struct fb_fix_screeninfo is not updated to this new
information. This patch fixes this issue. Also the function is changed to
just pass in struct drm_framebuffer so in the future we could use more
fields. I'm hoping some day fix->smem* could be set here :-)
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With cmwq, there's no reason for radeon to use a dedicated workqueue.
Drop dev_priv->wq and use system_wq instead.
Because radeon_driver_irq_uninstall_kms() may be called from
unsleepable context, the work items can't be flushed from there.
Instead, init and flush from radeon_irq_kms_init/fini().
While at it, simplify canceling/flushing of rdev->pm.dynpm_idle_work.
Always initialize and sync cancel instead of being unnecessarily smart
about it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The CMASK RAM is for colorbuffer compression (used in conjunction
with MSAA). Only one user (filp) can access it.
The CMASK RAM access is managed in the same way as Hyper-Z, but there is
a separate ioctl, because an app that uses MSAA does not necessarily
have to use zbuffering.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acer laptop (TravelMate 5730G) has an HDMI connector
on the laptop and a DVI connector on the docking station
and both share the same encoder, hpd pin, and ddc line.
The bios connector table reflects this and is technically
correct, however, we drop the DVI connector here since
xrandr has no concept of encoders (only crtcs and connectors)
and will try and drive both connectors with different crtcs
which isn't possible on the hardware side and leaves no crtcs
for LVDS or VGA.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=32732
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
stage 1: turn card on, switch boot vga pointer.
stage 2: switch fbs, switch mux and power off old card.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This improves the IGD/DIS picking using firstly if Intel, then
if the bus is bus 0. There may be a correct way to do this, but
I've no idea what it is.
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least on the nvidia mux the power switch seems to be executed
by the ACPI PS0/PS3 methods so need to do it explicitly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we have already detected something attached to the chip during
initialisation, always report the LVDS connector status as connected
during probing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Current 3D driver expects this behaviour. While this could be changed,
there's no compelling reason to reserve more than one subchannel for the
DRM. If we ever need to use an object other then M2MF, we can just
re-bind subchannel 0 as required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When hacking the libdrm for improvements, I triggered a kernel crash
related to the fact that the NOUVEAU_NOTIFIEROBJ_ALLOC ioctl calls
nouveau_channel_get with an unchecked channel index.
The patch ensures that the channel index is an unsigned and validates
its value in nouveau_channel_get.
Signed-off-by: Michel Hermier <hermier@frugalware.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
CONFIG_ACPI_VIDEO depends on more than just CONFIG_ACPI, so add those
dependencies to the Kconfig select condition. The case where some
dependencies fail to be satisfied should be handled correctly, because
in that case the ACPI_VIDEO symbols we use are converted into
static-inline stubs.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
