Some drivers erroneously use request_firmware() from their ->resume()
(or ->thaw(), or ->restore()) callbacks, which is not going to work
unless the firmware has been built in. This causes system resume to
stall until the firmware-loading timeout expires, which makes users
think that the resume has failed and reboot their machines
unnecessarily. For this reason, make _request_firmware() print a
warning and return immediately with error code if it has been called
when tasks are frozen and it's impossible to start any new usermode
helpers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
The driver core tries to prevent race conditions between runtime PM
and driver removal from happening by incrementing the runtime PM
usage counter of the device and executing pm_runtime_barrier() before
running the bus notifier and the ->remove() callbacks provided by the
device's subsystem or driver. This guarantees that, if a future
runtime suspend of the device has been scheduled or a runtime resume
or idle request has been queued up right before the driver removal,
it will be canceled or waited for to complete and no other
asynchronous runtime suspend or idle requests for the device will be
put into the PM workqueue until the ->remove() callback returns.
However, it doesn't prevent resume requests from being queued up
after pm_runtime_barrier() has been called and it doesn't prevent
pm_runtime_resume() from executing the device subsystem's runtime
resume callback. Morever, it prevents the device's subsystem or
driver from putting the device into the suspended state by calling
pm_runtime_suspend() from its ->remove() routine. This turns out to
be a major inconvenience for some subsystems and drivers that want to
leave the devices they handle in the suspended state.
To really prevent runtime PM callbacks from racing with the bus
notifier callback in __device_release_driver(), which is necessary,
because the notifier is used by some subsystems to carry out
operations affecting the runtime PM functionality, use
pm_runtime_get_sync() instead of the combination of
pm_runtime_get_noresume() and pm_runtime_barrier(). This will resume
the device if it's in the suspended state and will prevent it from
being suspended again until pm_runtime_put_*() is called.
To allow subsystems and drivers to put devices into the suspended
state by calling pm_runtime_suspend() from their ->remove() routines,
execute pm_runtime_put_sync() after running the bus notifier in
__device_release_driver(). This will require subsystems and drivers
to make their ->remove() callbacks avoid races with runtime PM
directly, but it will allow of more flexibility in the handling of
devices during the removal of their drivers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The freezer processes are dealing with multiple threads running
simultaneously, and on a UP system, the memory reads/writes do
not need barriers to keep things in sync. These are only needed
on SMP systems, so use SMP barriers instead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current implementation of suspend-to-RAM returns 0 if there is an
error from suspend_enter(), because suspend_devices_and_enter() ignores
the return value from suspend_enter(). This patch addresses this issue
and properly keep the error return from suspend_enter() and let
suspend_devices_and_enter relay the error return.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: fix a race between card-detect rescan and clock-gate work instances"
Fix new kernel-doc warning in mm/page_alloc.c:
Warning(mm/page_alloc.c:2370): No description found for parameter 'nid'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During pci remove/rescan testing found:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io 0x1000-0x0fff]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pci 0000:c0:03.0: Error enabling bridge (-22), continuing
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pcieport: probe of 0000:c0:03.0 failed with error -22
This bug was caused by commit c8adf9a3e8 ("PCI: pre-allocate
additional resources to devices only after successful allocation of
essential resources.")
After that commit, pci_hotplug_io_size is changed to additional_io_size
from minium size. So it will not go through resource_size(res) != 0
path, and will not be reset.
The root cause is: pci_bridge_check_ranges will set RESOURCE_IO flag for
pci bridge, and later if children do not need IO resource. those bridge
resources will not need to be allocated. but flags is still there.
that will confuse the the pci_enable_bridges later.
related code:
static void assign_requested_resources_sorted(struct resource_list *head,
struct resource_list_x *fail_head)
{
struct resource *res;
struct resource_list *list;
int idx;
for (list = head->next; list; list = list->next) {
res = list->res;
idx = res - &list->dev->resource[0];
if (resource_size(res) && pci_assign_resource(list->dev, idx)) {
...
reset_resource(res);
}
}
}
At last, We have to clear the flags in pbus_size_mem/io when requested
size == 0 and !add_head. becasue this case it will not go through
adjust_resources_sorted().
Just make size1 = size0 when !add_head. it will make flags get cleared.
At the same time when requested size == 0, add_size != 0, will still
have in head and add_list. because we do not clear the flags for it.
After this, we will get right result:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io disabled]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: irq 160 for MSI/MSI-X
pcieport 0000:c0:03.0: Signaling PME through PCIe PME interrupt
pci 0000:c4:00.0: Signaling PME through PCIe PME interrupt
pcie_pme 0000:c0:03.0:pcie01: service driver pcie_pme loaded
aer 0000:c0:03.0:pcie02: service driver aer loaded
pciehp 0000:c0:03.0:pcie04: Hotplug Controller:
v3: more simple fix. also fix one typo in pbus_size_mem
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Those reduced to DEBUG can possibly be triggered by unprivileged processes
and are nothing exceptional. Illegal checksum combinations can only be
caused by driver bug, so promote those messages to WARN.
Since GSO without SG will now only cause DEBUG message from
netdev_fix_features(), remove the workaround from register_netdevice().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization of vmxnet3, the state of LRO
gets out of sync with netdev->features.
This leads to very poor TCP performance in a IP forwarding
setup and is hitting many VMware users.
Simplified call sequence:
1. vmxnet3_declare_features() initializes "adapter->lro" to true.
2. The kernel automatically disables LRO if IP forwarding is enabled,
so vmxnet3_set_flags() gets called. This also updates netdev->features.
3. Now vmxnet3_setup_driver_shared() is called. "adapter->lro" is still
set to true and LRO gets enabled again, even though
netdev->features shows it's disabled.
Fix it by updating "adapter->lro", too.
The private vmxnet3 adapter flags are scheduled for removal
in net-next, see commit a0d2730c95
"net: vmxnet3: convert to hw_features".
Patch applies to 2.6.37 / 2.6.38 and 2.6.39-rc6.
Please CC: comments.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 747df2258b ('sfc: Always map MCDI
shared memory as uncacheable') introduced a separate mapping for the
MCDI shared memory (MC_TREG_SMEM). This means we can no longer easily
include it in the register dump. Since it is not particularly useful
in debugging, substitute a recognisable dummy value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: set the core dpll clk rate in its set_rate function
omap: iommu: Return IRQ_HANDLED in fault handler when no fault occured
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Take lock around probes for drm_fb_helper_hotplug_event
drm/i915: Revert i915.semaphore=1 default from 47ae63e0
vga_switcheroo: don't toggle-switch devices
drm/radeon/kms: add some evergreen/ni safe regs
drm/radeon/kms: fix extended lvds info parsing
drm/radeon/kms: fix tiling reg on fusion
We need to hold the dev->mode_config.mutex whilst detecting the output
status. But we also need to drop it for the call into
drm_fb_helper_single_fb_probe(), which indirectly acquires the lock when
attaching the fbcon.
Failure to do so exposes a race with normal output probing. Detected by
adding some warnings that the mutex is held to the backend detect routines:
[ 17.772456] WARNING: at drivers/gpu/drm/i915/intel_crt.c:471 intel_crt_detect+0x3e/0x373 [i915]()
[ 17.772458] Hardware name: Latitude E6400
[ 17.772460] Modules linked in: ....
[ 17.772582] Pid: 11, comm: kworker/0:1 Tainted: G W 2.6.38.4-custom.2 #8
[ 17.772584] Call Trace:
[ 17.772591] [<ffffffff81046af5>] ? warn_slowpath_common+0x78/0x8c
[ 17.772603] [<ffffffffa03f3e5c>] ? intel_crt_detect+0x3e/0x373 [i915]
[ 17.772612] [<ffffffffa0355d49>] ? drm_helper_probe_single_connector_modes+0xbf/0x2af [drm_kms_helper]
[ 17.772619] [<ffffffffa03534d5>] ? drm_fb_helper_probe_connector_modes+0x39/0x4d [drm_kms_helper]
[ 17.772625] [<ffffffffa0354760>] ? drm_fb_helper_hotplug_event+0xa5/0xc3 [drm_kms_helper]
[ 17.772633] [<ffffffffa035577f>] ? output_poll_execute+0x146/0x17c [drm_kms_helper]
[ 17.772638] [<ffffffff81193c01>] ? cfq_init_queue+0x247/0x345
[ 17.772644] [<ffffffffa0355639>] ? output_poll_execute+0x0/0x17c [drm_kms_helper]
[ 17.772648] [<ffffffff8105b540>] ? process_one_work+0x193/0x28e
[ 17.772652] [<ffffffff8105c6bc>] ? worker_thread+0xef/0x172
[ 17.772655] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772658] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772663] [<ffffffff8105f767>] ? kthread+0x7a/0x82
[ 17.772668] [<ffffffff8100a724>] ? kernel_thread_helper+0x4/0x10
[ 17.772671] [<ffffffff8105f6ed>] ? kthread+0x0/0x82
[ 17.772674] [<ffffffff8100a720>] ? kernel_thread_helper+0x0/0x10
Reported-by: Frederik Himpe <fhimpe@telenet.be>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36394
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My Q67 / i7-2600 box has rev09 Sandy Bridge graphics. It hangs
instantly when GNOME loads and it hangs so hard the reset button
doesn't work. Setting i915.semaphore=0 fixes it.
Semaphores were disabled in a1656b9090
in 2.6.38 and were re-enabled by
commit 47ae63e0c2
Merge: c59a333467cffb
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Mar 7 12:32:44 2011 +0000
Merge branch 'drm-intel-fixes' into drm-intel-next
Apply the trivial conflicting regression fixes, but keep GPU semaphores
enabled.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_execbuffer.c
(It's worth noting that the offending change is i915_drv.c,
which is not a conflict.)
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the requested device is already active, ignore the request.
This restores the original behaviour of the interface. The change was
probably an unintended side effect of
commit 66b37c6777 vga_switcheroo: split switching into two stages
which did not take into account to duplicate the !active check in the split-off
stage2.
Fix this by factoring that check out of stage1 into the debugfs_write routine.
References: https://bugzilla.kernel.org/show_bug.cgi?id=34252
Reported-by: Igor Murzov <e-mail@date.by>
Tested-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Without this patch every access to ip_vs in procfs will increase
the netns count i.e. an unbalanced get_net()/put_net().
(ipvsadm commands also use procfs.)
The result is you can't exit a netns if reading ip_vs_* procfs entries.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The commit 6b1e960fdb
bridge: Reset IPCB when entering IP stack on NF_FORWARD
broke forwarding of IPV6 packets in bridge because it would
call bp_parse_ip_options with an IPV6 packet.
Reported-by: Noah Meyerhans <noahm@debian.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Steps to reproduce the bug:
- Call FS_IOC_SETLFAGS ioctl with flags=FS_COMPR_FL
- Call FS_IOC_SETFLAGS ioctl with flags=0
- Call FS_IOC_GETFLAGS ioctl, and you'll see FS_COMPR_FL is still set!
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
FS_COW_FL and FS_NOCOW_FL were newly introduced to control per file
COW in btrfs, but FS_NOCOW_FL is sufficient.
The fact is we don't have corresponding BTRFS_INODE_COW flag.
COW is default, and FS_NOCOW_FL can be used to switch off COW for
a single file.
If we mount btrfs with nodatacow, a newly created file will be set with
the FS_NOCOW_FL flag. So to turn on COW for it, we can just clear the
FS_NOCOW_FL flag.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When a btrfs disk is created by mixed data & metadata option, it will have no
pure data or pure metadata space info.
In btrfs's for-linus branch, commit 78b1ea13838039cd88afdd62519b40b344d6c920
(Btrfs: fix OOPS of empty filesystem after balance) initializes space infos at
the very beginning. The problem is this initialization does not take the mixed
case into account, which will cause btrfs will easily get into ENOSPC in mixed
case.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If posix_acl_from_xattr() returns an error code, a negative address is
dereferenced causing an oops; fix by checking for error code first.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Shame on me! Commit b1dea800ac "tmpfs: fix race between umount and
writepage" fixed the advertized race, but introduced another: as even
its comment makes clear, we cannot safely rely on a peek at list_empty()
while holding no lock - until info->swapped is set, shmem_unuse_inode()
may delete any formerly-swapped inode from the shmem_swaplist, which
in this case would leave a swap area impossible to swapoff.
Although I don't relish taking the mutex every time, I don't care much
for the alternatives either; and at least the peek at list_empty() in
shmem_evict_inode() (a hotter path since most inodes would never have
been swapped) remains safe, because we already truncated the whole file.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 270dac35c2.
The commits causes command timeouts on AC plug/unplug. It isn't yet
clear why. As the commit was for a single rather obscure controller,
revert the change for now.
The problem was reported and bisected by Gu Rui in bug#34692.
https://bugzilla.kernel.org/show_bug.cgi?id=34692
Also, reported by Rafael and Michael in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1138771
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Gu Rui <chaos.proton@gmail.com>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Michael Leun <lkml20100708@newton.leun.net>
Cc: Jian Peng <jipeng2005@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the
if (num_registered_fb == FB_MAX)
return -ENXIO;
check _AFTER_ the call to do_remove_conflicting_framebuffers() as this
would (now in a safe way) allow a native driver to replace the
conflicting one even if all slots in registered_fb[] are taken.
This also prevents unregistering a framebuffer that is no longer
registered (vga16f will unregister at module unload time even if the
frame buffer had been unregistered earlier due to being found
conflicting).
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a register_framebuffer() call results in us removing old
conflicting framebuffers, the new registration_lock doesn't protect that
situation. And we can't just add the same locking to the function,
because these functions call each other: register_framebuffer() calls
remove_conflicting_framebuffers, which in turn calls
unregister_framebuffer for any conflicting entry.
In order to fix it, this just creates wrapper functions around all three
functions and makes the versions that actually do the work be called
"do_xxx()", leaving just the wrapper that gets the lock and calls the
worker function.
So the rule becomes simply that "do_xxxx()" has to be called with the
lock held, and now do_register_framebuffer() can just call
do_remove_conflicting_framebuffers(), and that in turn can call
_do_unregister_framebuffer(), and there is no deadlock, and we can hold
the registration lock over the whole sequence, fixing the races.
It also makes error cases simpler, and fixes one situation where we
would return from unregister_framebuffer() without releasing the lock,
pointed out by Bruno Prémont.
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Wire up syscalls new to 2.6.39
alpha: convert to clocksource_register_hz
Wire up the syscalls:
name_to_handle_at
open_by_handle_at
clock_adjtime
syncfs
and adjust some whitespace in the neighbourhood to align commments.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Converts alpha to use clocksource_register_hz.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matt Turner <mattst88@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bridge: fix forwarding of IPv6
bonding,llc: Fix structure sizeof incompatibility for some PDUs
ipv6: restore correct ECN handling on TCP xmit
ne-h8300: Fix regression caused during net_device_ops conversion
hydra: Fix regression caused during net_device_ops conversion
zorro8390: Fix regression caused during net_device_ops conversion
sfc: Always map MCDI shared memory as uncacheable
ehea: Fix memory hotplug oops
libertas: fix cmdpendingq locking
iwlegacy: fix IBSS mode crashes
ath9k: Fix a warning due to a queued work during S3 state
mac80211: don't start the dynamic ps timer if not associated
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4.1: Ensure that layoutget uses the correct gfp modes
NFSv4.1: remove pnfs_layout_hdr from pnfs_destroy_all_layouts tmp_list
NFSv41: Resend on NFS4ERR_RETRY_UNCACHED_REP
The rbd driver currently splits bios when they span an object boundary.
However, the blk_end_request expects the completions to roll up the results
in block device order, and the split rbd/ceph ops can complete in any
order. This patch adds a struct rbd_req_coll to track completion of split
requests and ensures that the results are passed back up to the block layer
in order.
This fixes errors where the file system gets completion of a read operation
that spans an object boundary before the data has actually arrived. The
bug is easily reproduced with iozone with a working set larger than
available RAM.
Reported-by: Fyodor Ustinov <ufm@ufm.su>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
The commit 6b1e960fdb
bridge: Reset IPCB when entering IP stack on NF_FORWARD
broke forwarding of IPV6 packets in bridge because it would
call bp_parse_ip_options with an IPV6 packet.
Reported-by: Noah Meyerhans <noahm@debian.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My Q67 / i7-2600 box has rev09 Sandy Bridge graphics. It hangs
instantly when GNOME loads and it hangs so hard the reset button
doesn't work. Setting i915.semaphore=0 fixes it.
Semaphores were disabled in a1656b9090 ("drm/i915: Disable GPU
semaphores by default") in 2.6.38 but were then re-enabled (by mistake?)
by the merge 47ae63e0c2 ("Merge branch 'drm-intel-fixes' into
drm-intel-next").
(It's worth noting that the offending change is i915_drv.c, which was
not marked as a conflict - although a 'git show --cc' on the merge does
show that neither parent had it set to 1)
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With some combinations of arch/compiler (e.g. arm-linux-gcc) the sizeof
operator on structure returns value greater than expected. In cases when the
structure is used for mapping PDU fields it may lead to unexpected results
(such as holes and alignment problems in skb data). __packed prevents this
undesired behavior.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a hot function, and we're better off not mixing types in the mask
calculations. The compiler just ends up mixing 16-bit and 32-bit
operations, for no good reason.
So do everything in 'unsigned int' rather than mixing 'unsigned int'
masking with a 'umode_t' (16-bit) mode variable.
This, together with the parent commit (47a150edc2: "Cache user_ns in
struct cred") makes acl_permission_check() much nicer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If !CONFIG_USERNS, have current_user_ns() defined to (&init_user_ns).
Get rid of _current_user_ns. This requires nsown_capable() to be
defined in capability.c rather than as static inline in capability.h,
so do that.
Request_key needs init_user_ns defined at current_user_ns if
!CONFIG_USERNS, so forward-declare that in cred.h if !CONFIG_USERNS
at current_user_ns() define.
Compile-tested with and without CONFIG_USERNS.
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
[ This makes a huge performance difference for acl_permission_check(),
up to 30%. And that is one of the hottest kernel functions for loads
that are pathname-lookup heavy. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The debug l3_ick/rate is not displaying the actual rate of the clock in
hardware. This is because, the core dpll set_rate function doesn't update the
clk.rate. After fixing, the l3_ick/rate is displaying proper values.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On rev <= 1.1 tables, the offset is absolute,
on newer tables, it's relative.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=700326
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The location of MC_ARB_RAMCFG changed on fusion.
I've diffed all the other regs in evergreend.h and this
is the only other reg that changed.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
