1. add c_x86_vendor into cpu_dev
2. change cpu_devs to static
3. check c_x86_vendor before put that cpu_dev into array
4. remove alignment for 64bit
5. order the sequence in cpu_devs according to link sequence...
so could put intel at first, then amd...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
v2: make 64 bit get c->x86_cache_alignment = c->x86_clfush_size
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1. add extended_cpuid_level for 32bit
2. add generic_identify for 64bit
3. add early_identify_cpu for 32bit
4. early_identify_cpu not be called by identify_cpu
5. remove early in get_cpu_vendor for 32bit
6. add get_cpu_cap
7. add cpu_detect for 64bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move early cpu initialization after cpu early get cap so the
early cpu initialization can fix up cpu caps.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Krzysztof Helt found MTRR is not detected on k6-2
root cause:
we moved mtrr_bp_init() early for mtrr trimming,
and in early_detect we only read the CPU capability from cpuid,
so some cpu doesn't have that bit in cpuid.
So we need to add early_init_xxxx to preset those bit before mtrr_bp_init
for those earlier cpus.
this patch is for v2.6.27
Reported-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have had a number of cases where <asm/cpufeature.h> (and its
predecessors) have diverged substantially from the names list in
/proc/cpuinfo. This patch generates the latter from the former.
It retains the option for explicitly overriding the strings, but by
making that require a separate action it should at least be less
likely to happen.
It would be good to do a future pass and rename strings that are
gratuituously different in the kernel (/proc/cpuinfo is a userspace
interface and must remain constant.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The removal of the CPU from the various maps was redundant as it already
happened in cpu_disable.
After cleaning this up, cpu_uninit only resets the tlb state, so rename
it and create a noop version for the X86_64 case (so the two play_deads
can be unified later).
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During CPU hot-remove the sysfs directory created by
threshold_create_bank(), defined in
arch/x86/kernel/cpu/mcheck/mce_amd_64.c, has to be removed before
its parent directory, created by mce_create_device(), defined in
arch/x86/kernel/cpu/mcheck/mce_64.c . Moreover, when the CPU in
question is hotplugged again, obviously the latter has to be created
before the former. At present, the right ordering is not enforced,
because all of these operations are carried out by CPU hotplug
notifiers which are not appropriately ordered with respect to each
other. This leads to serious problems on systems with two or more
multicore AMD CPUs, among other things during suspend and hibernation.
Fix the problem by placing threshold bank CPU hotplug callbacks in
mce_cpu_callback(), so that they are invoked at the right places,
if defined. Additionally, use kobject_del() to remove the sysfs
directory associated with the kobject created by
kobject_create_and_add() in threshold_create_bank(), to prevent the
kernel from crashing during CPU hotplug operations on systems with
two or more multicore AMD CPUs.
This patch fixes bug #11337.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andi Kleen <andi@firstfloor.org>
Tested-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpuid leaf 0xb provides extended topology enumeration. This interface provides
the 32-bit x2APIC id of the logical processor and it also provides a new
mechanism to detect SMT and core siblings (which provides increased
addressability).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: work around MTRR mask setting, v2
x86: fix section mismatch warning - uv_cpu_init
x86: fix VMI for early params
x86: fix two modpost warnings in mm/init_64.c
x86: fix 1:1 mapping init on 64-bit (memory hotplug case)
x86: work around MTRR mask setting
x86: PAT Update validate_pat_support for intel CPUs
devmem, x86: PAT Change /dev/mem mmap with O_SYNC to use UC_MINUS
x86: PAT proper tracking of set_memory_uc and friends
x86: fix BUG: unable to handle kernel paging request (numaq_tsc_disable)
x86: export pv_lock_ops non-GPL
x86, mmiotrace: silence section mismatch warning - leave_uniprocessor
x86: use WARN() in arch/x86/kernel
x86: use WARN() in arch/x86/mm/ioremap.c
werror: fix pci calgary
x86: fix oprofile + hibernation badness
x86, SGI UV: hardcode the TLB flush interrupt system vector
x86: fix Xorg startup/shutdown slowdown with PAT
x86: fix "kernel won't boot on a Cyrix MediaGXm (Geode)"
x86 iommu: remove unneeded parenthesis
improve the debug printout:
- make it actually display something
- print it only once
would be nice to have a WARN_ONCE() facility, to feed such things to
kerneloops.org.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joshua Hoblitt reported that only 3 GB of his 16 GB of RAM is
usable. Booting with mtrr_show showed us the BIOS-initialized
MTRR settings - which are all wrong.
So the root cause is that the BIOS has not set the mask correctly:
> [ 0.429971] MSR00000200: 00000000d0000000
> [ 0.433305] MSR00000201: 0000000ff0000800
> should be ==> [ 0.433305] MSR00000201: 0000003ff0000800
>
> [ 0.436638] MSR00000202: 00000000e0000000
> [ 0.439971] MSR00000203: 0000000fe0000800
> should be ==> [ 0.439971] MSR00000203: 0000003fe0000800
>
> [ 0.443304] MSR00000204: 0000000000000006
> [ 0.446637] MSR00000205: 0000000c00000800
> should be ==> [ 0.446637] MSR00000205: 0000003c00000800
>
> [ 0.449970] MSR00000206: 0000000400000006
> [ 0.453303] MSR00000207: 0000000fe0000800
> should be ==> [ 0.453303] MSR00000207: 0000003fe0000800
>
> [ 0.456636] MSR00000208: 0000000420000006
> [ 0.459970] MSR00000209: 0000000ff0000800
> should be ==> [ 0.459970] MSR00000209: 0000003ff0000800
So detect this borkage and add the prefix 111.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pentium III and Core Solo/Duo CPUs have an erratum
" Page with PAT set to WC while associated MTRR is UC may consolidate to UC "
which can result in WC setting in PAT to be ineffective. We will disable
PAT on such CPUs, so that we can continue to use MTRR WC setting.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use WARN() instead of a printk+WARN_ON() pair; this way the message
becomes part of the warning section for better reporting/collection.
This also allowed the folding of some if()'s into the WARN()
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cyrix MediaGXm/Cx5530 Unicorn Revision 1.19.3B has stopped
booting starting at v2.6.22.
The reason is this commit:
> commit f25f64ed5b
> Author: Juergen Beisert <juergen@kreuzholzen.de>
> Date: Sun Jul 22 11:12:38 2007 +0200
>
> x86: Replace NSC/Cyrix specific chipset access macros by inlined functions.
this commit activated a macro which was dormant before due to (buggy)
macro side-effects.
I've looked through various datasheets and found that the GXm and GXLV
Geode processors don't have an incrementor.
Remove the incrementor setup entirely. As the incrementor value
differs according to clock speed and we would hope that the BIOS
configures it correctly, it is probably the right solution.
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 34ae7f35a2, which has
been reported to cause a number of problems. During suspend and resume,
it apparently causes a crash in a CPU hotplug notifier to happen,
although the exact details are sketchy because of the inability to get
good traces during the suspend sequence.
See buzilla entries
http://bugzilla.kernel.org/show_bug.cgi?id=11296http://bugzilla.kernel.org/show_bug.cgi?id=11339
for more examples and details.
[ Mark: "Revert the patch for now. I'm still looking into getting a
reliable reproduction and I do not have a fix at this time." ]
Requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@inux-foundation.org>
The long noops ("NOPL") are supposed to be detected by family >= 6.
Unfortunately, several non-Intel x86 implementations, both hardware
and software, don't obey this dictum. Instead, probe for NOPL
directly by executing a NOPL instruction and see if we get #UD.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch adds some configuration options that allow to compile out
CPU vendor-specific code in x86 kernels (in arch/x86/kernel/cpu). The
new configuration options are only visible when CONFIG_EMBEDDED is
selected, as they are mostly interesting for space savings reasons.
An example of size saving, on x86 with only Intel CPU support:
text data bss dec hex filename
1125479 118760 212992 1457231 163c4f vmlinux.old
1121355 116536 212992 1450883 162383 vmlinux
-4124 -2224 0 -6348 -18CC +/-
However, I'm not exactly sure that the Kconfig wording is correct with
regard to !64BIT / 64BIT.
[ mingo@elte.hu: convert macro to inline ]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/cpu/intel.c defines a few fallback functions
(cmpxchg_*()) that are used when the CPU doesn't support cmpxchg
and/or cmpxchg64 natively. However, while defined in an Intel-specific
file, these functions are also used for CPUs from other vendors when
they don't support cmpxchg and/or cmpxchg64. This breaks the
compilation when support for Intel CPUs is disabled.
This patch moves these functions to a new
arch/x86/kernel/cpu/cmpxchg.c file, unconditionally compiled when
X86_32 is enabled.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: michael@free-electrons.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
movsl_mask is currently defined in arch/x86/kernel/cpu/intel.c, which
contains code specific to Intel CPUs. However, movsl_mask is used in
the non-CPU specific code in arch/x86/lib/usercopy_32.c, which breaks
the compilation when support for Intel CPUs is compiled out.
This patch solves this problem by moving movsl_mask's definition close
to its users in arch/x86/lib/usercopy_32.c.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: michael@free-electrons.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, setup_p4_watchdog() use CCCR_OVF_PMI1 to enable the counter
overflow interrupts to the second logical core. But this bit doesn't work
on Pentium 4 Ds (model 4, stepping 4) and this patch avoids its use on
these processors. Tested on 4 different machines that have this
specific model with success.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: jvillalovos@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix 2.6.27rc1 cannot boot more than 8CPUs
x86: make "apic" an early_param() on 32-bit, NULL check
EFI, x86: fix function prototype
x86, pci-calgary: fix function declaration
x86: work around gcc 3.4.x bug
x86: make "apic" an early_param() on 32-bit
x86, debug: tone down arch/x86/kernel/mpparse.c debugging printk
x86_64: restore the proper NR_IRQS define so larger systems work.
x86: Restore proper vector locking during cpu hotplug
x86: Fix broken VMI in 2.6.27-rc..
x86: fdiv bug detection fix
Exception stacks are allocated each time a CPU is set online.
But the allocated space is never freed. Thus with one CPU hotplug
offline/online cycle there is a memory leak of 24K (6 pages) for
a CPU.
Fix is to allocate exception stacks only once -- when the CPU is
set online for the first time.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pda->irqstackptr is allocated whenever a CPU is set online.
But it is never freed. This results in a memory leak of 16K
for each CPU offline/online cycle.
Fix is to allocate pda->irqstackptr only once.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch provides support for the _PSD ACPI object in the Powernow-k8
driver. Although it looks like an invasive patch, most of it is
simply the consequence of turning the static acpi_performance_data
structure into a pointer.
AMD has tested it on several machines over the past few days without issue.
[trivial checkpatch warnings fixed up by davej]
[X86_POWERNOW_K8_ACPI=n buildfix from Randy Dunlap]
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Tested-by: Frank Arnold <frank.arnold@amd.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dave Jones <davej@redhat.com>
arch/x86/kernel/cpu/cpufreq/elanfreq.c:47:26: warning: symbol 'elan_multiplier' was not declared. Should it be static?
Yes, yes it should.
Signed-off-by: Dave Jones <davej@redhat.com>
The fdiv detection code writes s32 integer into
the boot_cpu_data.fdiv_bug.
However, the boot_cpu_data.fdiv_bug is only char (s8)
field so the detection overwrites already set fields for
other bugs, e.g. the f00f bug field.
Use local s32 variable to receive result.
This is a partial fix to Bugzilla #9928 - fixes wrong
information about the f00f bug (tested) and probably
for coma bug (I have no cpu to test this).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Uses xsave/xrstor (instead of traditional fxsave/fxrstor) in context switch
when available.
Introduces TS_XSAVE flag, which determine the need to use xsave/xrstor
instructions during context switch instead of the legacy fxsave/fxrstor
instructions. Thread-synchronous status word is already in L1 cache during
this code patch and thus minimizes the performance penality compared to
(cpu_has_xsave) checks.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Enables xsave/xrstor by turning on cr4.osxsave on cpu's which have
the xsave support. For now, features that OS supports/enabled are
FP and SSE.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix !PCI build failure:
arch/x86/kernel/cpu/intel_cacheinfo.c: In function 'get_k8_northbridge':
arch/x86/kernel/cpu/intel_cacheinfo.c:675: error: implicit declaration of function 'pci_match_id'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Monday 21 July 2008, Ingo Molnar wrote:
> > applied to tip/x86/cpu, thanks Mark.
> >
> > I've done some coding style fixes for the new functions you've
> > introduced, see that commit below.
>
> -tip testing found the following build failure:
>
> arch/x86/kernel/built-in.o: In function `show_cache_disable':
> intel_cacheinfo.c:(.text+0xbbf2): undefined reference to `k8_northbridges'
> arch/x86/kernel/built-in.o: In function `store_cache_disable':
> intel_cacheinfo.c:(.text+0xbd91): undefined reference to `k8_northbridges'
>
> please send a delta fix patch against the tip/x86/cpu branch:
>
> http://people.redhat.com/mingo/tip.git/README
>
> which has your patch plus the cleanup applied.
delta fix patch follows. It removes the dependency on k8_northbridges.
-Mark Langsdorf
Operating System Research Center
AMD
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
New versions of AMD processors have support to disable parts
of their L3 caches if too many MCEs are generated by the
L3 cache.
This patch provides a /sysfs interface under the cache
hierarchy to display which caches indices are disabled
(if any) and to monitoring applications to disable a
cache index.
This patch does not set an automatic policy to disable
the L3 cache. Policy decisions would need to be made
by a RAS handler. This patch merely makes it easier to
see what indices are currently disabled.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
Use the new generic int attribute accessors for the x86 mce tolerant
attribute. Simple example to illustrate the new macros.
There are much more places all over the tree that could be converted
like this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a couple of places where (P)Dprintk is used which is an old
compile time enabled printk wrapper. Convert it to the generic
pr_debug().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
... so don't need to call clear_cpu_cap again in early_identify_cpu,
and could use cleared_cpu_caps like other places.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some cleanups in speedstep-centrino.c for NR_CPUS=4096.
* Use new CPUMASK_PTR (instead of old CPUMASK_VAR).
* Replace arrays sized by NR_CPUS with percpu variables.
* Cleanup some formatting problems (>80 chars per line)
and other checkpatch complaints.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Use nr_cpu_ids instead of NR_CPUS to limit traversal of cpu online map.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* nr_cpu_ids should be used to allocate arrays based on the number of
cpu's present.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's not used anywhere outside its single referencing file.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* Use the CPUMASK_ALLOC macros in the centrino_target() function.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* This patch replaces the dangerous lvalue version of cpumask_of_cpu
with new cpumask_of_cpu_ptr macros. These are patterned after the
node_to_cpumask_ptr macros.
In general terms, if there is a cpumask_of_cpu_map[] then a pointer to
the cpumask_of_cpu_map[cpu] entry is used. The cpumask_of_cpu_map
is provided when there is a large NR_CPUS count, reducing
greatly the amount of code generated and stack space used for
cpumask_of_cpu(). The pointer to the cpumask_t value is needed for
calling set_cpus_allowed_ptr() to reduce the amount of stack space
needed to pass the cpumask_t value.
If there isn't a cpumask_of_cpu_map[], then a temporary variable is
declared and filled in with value from cpumask_of_cpu(cpu) as well as
a pointer variable pointing to this temporary variable. Afterwards,
the pointer is used to reference the cpumask value. The compiler
will optimize out the extra dereference through the pointer as well
as the stack space used for the pointer, resulting in identical code.
A good example of the orthogonal usages is in net/sunrpc/svc.c:
case SVC_POOL_PERCPU:
{
unsigned int cpu = m->pool_to[pidx];
cpumask_of_cpu_ptr(cpumask, cpu);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, cpumask);
return 1;
}
case SVC_POOL_PERNODE:
{
unsigned int node = m->pool_to[pidx];
node_to_cpumask_ptr(nodecpumask, node);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, nodecpumask);
return 1;
}
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The force_mwait variable iss defined either in
arch/x86/kernel/cpu/amd.c or in arch/x86/kernel/setup_64.c, but it is
only initialized and used in arch/x86/kernel/process.c. This patch
moves the declaration to arch/x86/kernel/process.c.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: michael@free-electrons.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This avoids calling kobject_uevent() with cache_kobject that has
already been deallocated in an error path.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use alternatives to select the workaround for the 11AP Pentium erratum
for the affected steppings on the fly rather than build time. Remove the
X86_GOOD_APIC configuration option and replace all the calls to
apic_write_around() with plain apic_write(), protecting accesses to the
ESR as appropriate due to the 3AP Pentium erratum. Remove
apic_read_around() and all its invocations altogether as not needed.
Remove apic_write_atomic() and all its implementing backends. The use of
ASM_OUTPUT2() is not strictly needed for input constraints, but I have
used it for readability's sake.
I had the feeling no one else was brave enough to do it, so I went ahead
and here it is. Verified by checking the generated assembly and tested
with both a 32-bit and a 64-bit configuration, also with the 11AP
"feature" forced on and verified with gdb on /proc/kcore to work as
expected (as an 11AP machines are quite hard to get hands on these days).
Some script complained about the use of "volatile", but apic_write() needs
it for the same reason and is effectively a replacement for writel(), so I
have disregarded it.
I am not sure what the policy wrt defconfig files is, they are generated
and there is risk of a conflict resulting from an unrelated change, so I
have left changes to them out. The option will get removed from them at
the next run.
Some testing with machines other than mine will be needed to avoid some
stupid mistake, but despite its volume, the change is not really that
intrusive, so I am fairly confident that because it works for me, it will
everywhere.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AMD only supports "syscall" from 32-bit compat usermode.
Intel and Centaur(?) only support "sysenter" from 32-bit compat usermode.
Set the X86 feature bits accordingly, and set up the vdso in
accordance with those bits. On the offchance we run on in a 64-bit
environment which supports neither syscall nor sysenter from 32-bit
mode, then fall back to the int $0x80 vdso.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Update arch/x86's use of page-aligned variables. The change to
arch/x86/xen/mmu.c fixes an actual bug, but the rest are cleanups
and to set a precedent.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when try to make hpet_enable use io_remap instead fixmap got
ioremap: invalid physical address fed00000
------------[ cut here ]------------
WARNING: at arch/x86/mm/ioremap.c:161 __ioremap_caller+0x8c/0x2f3()
Modules linked in:
Pid: 0, comm: swapper Not tainted 2.6.26-rc9-tip-01873-ga9827e7-dirty #358
Call Trace:
[<ffffffff8026615e>] warn_on_slowpath+0x6c/0xa7
[<ffffffff802e2313>] ? __slab_alloc+0x20a/0x3fb
[<ffffffff802d85c5>] ? mpol_new+0x88/0x17d
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8024b0d2>] __ioremap_caller+0x8c/0x2f3
[<ffffffff80e86dbd>] ? hpet_enable+0x39/0x241
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8024b466>] ioremap_nocache+0x2a/0x40
[<ffffffff80e86dbd>] hpet_enable+0x39/0x241
[<ffffffff80e7a1f6>] hpet_time_init+0x21/0x4e
[<ffffffff80e730e9>] start_kernel+0x302/0x395
[<ffffffff80e722aa>] x86_64_start_reservations+0xb9/0xd4
[<ffffffff80e722fe>] ? x86_64_init_pda+0x39/0x4f
[<ffffffff80e72400>] x86_64_start_kernel+0xec/0x107
---[ end trace a7919e7f17c0a725 ]---
it seems for amd system that is set later...
try to move setting early in early_identify_cpu.
and remove same code for intel and centaur.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
got this on a test-system:
calling numaq_tsc_disable+0x0/0x39
NUMAQ: disabling TSC
initcall numaq_tsc_disable+0x0/0x39 returned 0 after 0 msecs
that's because we should not be using arch_initcall to call numaq_tsc_disable.
need to call it in setup_arch before time_init()/tsc_init()
and call it in init_intel() to make the cpu feature bits right.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
tighten the boundary checks around max_low_pfn_mapped - dont overmap
nor undermap into holes.
also print out tseg for AMD cpus, for diagnostic purposes.
(this is an SMM area, and we split up any big mappings around that area)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x2apic support. Interrupt-remapping must be enabled before enabling x2apic,
this is needed to ensure that IO interrupts continue to work properly after the
cpu mode is changed to x2apic(which uses 32bit extended physical/cluster
apic id).
On systems where apicid's are > 255, BIOS can handover the control to OS in
x2apic mode. Or if the OS handover was in legacy xapic mode, check
if it is capable of x2apic mode. And if we succeed in enabling
Interrupt-remapping, then we can enable x2apic mode in the CPU.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add pseudo-feature bits to describe whether the CPU supports sysenter
and/or syscall from ia32-compat userspace. This removes a hardcoded
test in vdso32-setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This removes a pile of buggy open-coded implementations of savesegment
and loadsegment.
(They are buggy because they don't have memory barriers to prevent
them from being reordered with respect to memory accesses.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1. move out calling of check_enable_amd_mmconf_dmi out of setup_64.c
put it into init_amd(), so don't need to make extra dmi check for
system with other cpus.
2. 15 --> 0xf
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
rename update_memory_range to e820_update_range
rename add_memory_region to e820_add_region
to make it more clear that they are about e820 map operations.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"Form follows function". Code is now where it belongs to.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
C1E on AMD machines is like C3 but without control from the OS. Up to
now we disabled the local apic timer for those machines as it stops
when the CPU goes into C1E. This excludes those machines from high
resolution timers / dynamic ticks, which hurts especially X2 based
laptops.
The current boot time C1E detection has another, more serious flaw
as well: some BIOSes do not enable C1E until the ACPI processor module
is loaded. This causes systems to stop working after that point.
To work nicely with C1E enabled machines we use a separate idle
function, which checks on idle entry whether C1E was enabled in the
Interrupt Pending Message MSR. This allows us to do timer broadcasting
for C1E and covers the late enablement of C1E as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Quirks getting ignored was a bug. Below patch fixes the bug, until
we have the dynamic banks support.
Sysfs choice configuration should not have any issues with the earlier patch
as we look for NR_SYSFS_BANKS in do_machine_check().
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
attached is a no-brainer that makes kernel correctly report
NR_BANKS for MCE. We are right now limited to NR_BANKS==6, but the
error message will use the available number of banks instead of the
defined maximum.
For a Nehalem based system it will print:
"MCE: warning: using only 9 banks"
while the correct message would be
"MCE: warning: using only 6 banks"
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Starting with commit 8d4a430085 (x86:
cleanup PAT cpu validation) the PAT CPU feature flag is not cleared
anymore. Now the error message
"PAT enabled, but CPU feature cleared"
in pat_init() is misleading.
Furthermore the current code does not check for existence of the PAT
CPU feature flag if a CPU is whitelisted in validate_pat_support.
This patch clears pat_wc_enabled if boot CPU has no PAT feature flag
and adapts the paranoia check.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If PAT support is advertised it should just work. No errata known.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simplify code: no need to do a cpuid(1) again. The cpuinfo structure
has all necessary information already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the "MSR_K8_ENABLE_C1E" MSR to INT_PENDING_MSG, which is the
name in the data sheet as well. Move the C1E mask to the header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch does check if CPU is being recongnized
before call the unreserve(). Since enable_lapic_nmi_watchdog()
does have such a check the same is make sense here too
in a sake of code consistency (but nothing more).
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: macro@linux-mips.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It looks good to move bugs_64.c to cpu/bugs_64.c.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch implements PCI extended configuration space access for
AMD's Barcelona CPUs. It extends the method using CF8/CFC IO
addresses. An x86 capability bit has been introduced that is set for
CPUs supporting PCI extended config space accesses.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Create a separate centaur_64.c file in the cpu/ dir for
the useful parts to live in.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Create a separate intel_64.c file in the cpu/ dir for
the useful parts to live in.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Create a separate amd_64.c file in the cpu/ dir for
the useful parts to live in.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
disable the noisy print out.
also use the one the less spare mtrr reg.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
there is a typo in the mask value, need to remove that extra 0,
to avoid 4bit clearing.
Signed-off-by: Yinghal Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
otherwise fixed MTRR for family 10h may not be changed.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Loop through mtrr chunk_size and gran_size from 1M to 2G to find out
the optimal value so user does not need to add mtrr_chunk_size and
mtrr_gran_size to the kernel command line.
If optimal value is not found, print out all list to help select less
optimal value.
Add mtrr_spare_reg_nr= so user could set 2 instead of 1, if the card
need more entries.
v2: find the one with more spare entries
v3: fix hole_basek offset
v4: tight the compare between range and range_new
loop stop with 4g
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Gabriel C <nix.or.die@googlemail.com>
Cc: Mika Fischer <mika.fischer@zoopnet.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
v9: address format change requests by Ingo
more case handling in range_to_var_with_hole
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
v2: process hole then end_pfn
fix update_memory_range with whole cover comparing
Signed-off-by: Yinghai Lu <yinghai.lu@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
converting MTRR layout from continous to discrete, some time could run out of
MTRRs. So add gran_sizek to prevent that by dumpping small RAM piece less than
gran_sizek.
previous trimming only can handle highest_pfn from mtrr to end_pfn from e820.
when have more than 4g RAM installed, there will be holes below 4g. so need to
check ram below 4g is coverred well.
need to be applied after
[PATCH] x86: mtrr cleanup for converting continuous to discrete layout v7
Signed-off-by: Yinghai Lu <yinghai.lu@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some BIOS like to use continus MTRR layout, and X driver can not add
WB entries for graphical cards when 4g or more RAM installed.
the patch will change MTRR to discrete.
mtrr_chunk_size= could be used to have smaller continuous block to hold holes.
default is 256m, could be set according to size of graphics card memory.
mtrr_gran_size= could be used to send smallest mtrr block to avoid run out of MTRRs
v2: fix -1 for UC checking
v3: default to disable, and need use enable_mtrr_cleanup to enable this feature
skip the var state change warning.
remove next_basek in range_to_mtrr()
v4: correct warning mask.
v5: CONFIG_MTRR_SANITIZER
v6: fix 1g, 2g, 512 aligment with extra hole
v7: gran_sizek to prevent running out of MTRRs.
v8: fix hole_basek caculation caused when removing next_basek
gran_sizek using when basek is 0.
need to apply
[PATCH] x86: fix trimming e820 with MTRR holes.
right after this one.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/cpu/mtrr/generic.c:216:12: warning: symbol 'lo' shadows an earlier one
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just moved trailing statements to the next line, removed space before
open/close parenthesis, wrapped long lines.
Signed-off-by: Miklos Vajna <vmiklos@frugalware.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While examining holes in percpu section I found this :
c05f5000 D per_cpu__current_task
c05f5000 D __per_cpu_start
c05f5004 D per_cpu__cpu_number
c05f5008 D per_cpu__irq_regs
c05f500c d per_cpu__cpu_devices
c05f5040 D per_cpu__cyc2ns
<Big Hole of about 4000 bytes>
c05f6000 d per_cpu__cpuid4_info
c05f6004 d per_cpu__cache_kobject
c05f6008 d per_cpu__index_kobject
<Big Hole of about 4000 bytes>
c05f7000 D per_cpu__gdt_page
This is because gdt_page is a percpu variable, defined with
a page alignement, and linker is doing its job, two times because of .o
nesting in the build process.
I introduced a new macro DEFINE_PER_CPU_PAGE_ALIGNED() to avoid
wasting this space. All page aligned variables (only one at this time)
are put in a separate
subsection .data.percpu.page_aligned, at the very begining of percpu zone.
Before patch , on a x86_32 machine :
.data.percpu 30232 3227471872
.data.percpu 22168 3227471872
Thats 8064 bytes saved for each CPU.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change references from for_each_cpu_mask to for_each_cpu_mask_nr
where appropriate
Reviewed-by: Paul Jackson <pj@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 2d474871e2fb092eb46a0930aba5442e10eb96cc
Author: Mike Travis <travis@sgi.com>
Date: Mon May 12 21:21:13 2008 +0200
Unconditionally enable PAT support on Centaur and Transmeta CPUs.
All known models that advertise PAT have no known errata.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The longrun cpufreq module reports a false minimum frequency 3MHz on
300-600MHz Crusoe processor. This may be due to a calculation bug
in the module.
Original patch from Kaz Sasayama <kazssym@hypercore.co.jp>
submitted as http://bugs.debian.org/468149 patch ported to x86
Cc: Kaz Sasayama <kazssym@hypercore.co.jp>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Dave Jones <davej@redhat.com>
The most common error with powernow-k8 is an ACPI _PSS error
caused either by failure to load the ACPI processor module
or a bad parse of the _PSS object. Make the error message
returned to the user in these situations more straightforward
and easier to understand.
-Mark Langsdorf
Operating System Research Center
AMD
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The latest rev of Intel doc AP-485 details a new cache
descriptor that we don't yet support.
A 6MB 24-way assoc L2 cache.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Eliminate the 6 bank restriction in 64 bit mce reporting code. This
restriction is artificial (due to static creation of sysfs files) and 32
bit code does not have any such restriction.
This change helps in reporting the details of machine checks on a
machine check exception with errors in bank 6 and above on CPUs that
support those banks. Without the patch, machine check errors in those
banks are not reported.
We still have 128 (MCE_EXTENDED_BANK) bank restriction instead of max
256 supported in hardware. That is not changed in the patch below as it
will have some user level mcelog utility dependency, with bank 128 being
used for thermal reporting currently.
The patch below does not create sysfs control (bankNctl) for banks
higher than 6 as well. That needs some pre-cleanup in /sysfs mce layout,
removal of per cpu /sysfs entries for bankctl as they are really global
system level control today. That change will follow. This basic change
is critical to report the detailed errors on banks higher than 6.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Polish the ds.h interface and add support for PEBS.
Ds.c is meant to be the resource allocator for per-thread and per-cpu
BTS and PEBS recording.
It is used by ptrace/utrace to provide execution tracing of debugged tasks.
It will be used by profilers (e.g. perfmon2).
It may be used by kernel debuggers to provide a kernel execution trace.
Changes in detail:
- guard DS and ptrace by CONFIG macros
- separate DS and BTS more clearly
- simplify field accesses
- add functions to manage PEBS buffers
- add simple protection/allocation mechanism
- added support for Atom
Opens:
- buffer overflow handling
Currently, only circular buffers are supported. This is all we need
for debugging. Profilers would want an overflow notification.
This is planned to be added when perfmon2 is made to use the ds.h
interface.
- utrace intermediate layer
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the scattered checks for PAT support to a single function. Its
moved to addon_cpuid_features.c as this file is shared between 32 and
64 bit.
Remove the manipulation of the PAT feature bit and just disable PAT in
the PAT layer, based on the PAT bit provided by the CPU and the
current CPU version/model white list.
Change the boot CPU check so it works on Voyager somewhere in the
future as well :) Also panic, when a secondary has PAT disabled but
the primary one has alrady switched to PAT. We have no way to undo
that.
The white list is kept for now to ensure that we can rely on known to
work CPU types and concentrate on the software induced problems
instead of fighthing CPU erratas and subtle wreckage caused by not yet
verified CPUs. Once the PAT code has stabilized enough, we can remove
the white list and open the can of worms.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] state info wrong after resume
[CPUFREQ] allow use of the powersave governor as the default one
[CPUFREQ] document the currently undocumented parts of the sysfs interface
[CPUFREQ] expose cpufreq coordination requirements regardless of coordination mechanism
Remove proc_root export. Creation and removal works well if parent PDE is
supplied as NULL -- it worked always that way.
So, one useless export removed and consistency added, some drivers created
PDEs with &proc_root as parent but removed them as NULL and so on.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As written, this can never be true.
Spotted by the Sparse checker.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, affected_cpus shows which CPUs need to have their frequency
coordinated in software. When hardware coordination is in use, the contents
of this file appear the same as when no coordination is required. This can
lead to some confusion among user-space programs, for example, that do not
know that extra coordination is required to force a CPU core to a particular
speed to control power consumption.
To fix this, create a "related_cpus" attribute that always displays the
coordination map regardless of whatever coordination strategy the cpufreq
driver uses (sw or hw). If the cpufreq driver does not provide a value, fall
back to policy->cpus.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
We checked the hardware freq with OS cached freq value in get_cur_freqon_cpu().
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
It is claimed that NexGen CPUs were never shipped:
http://lkml.org/lkml/2008/4/20/179
Also, the kernel support for these chips has been broken for
a long time, the code intended to support NexGen thereby being
essentially dead.
As an outcome of the discussion that can be found using the URL
above, this patch removes the NexGen support altogether.
The changes in this patch survived a defconfig build for i386, a
couple of successful randconfig builds, as well as a runtime test,
which consisted in booting a 32-bit x86 box up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are no users for the function amd_init_cpu() defined in
arch/x86/kernel/cpu/amd.c. This patch removes this routine.
This patch was build-tested using defconfigs for i386 and x86_64,
and a few randconfig instances. Runtime tests were performed by
booting 32- and 64-bit x86 boxen up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At least on my Barcelona, I see MCE log entries after cold boot caused
by BIOS not properly clearing the respective registers. Therefore, this
patch extends the workaround to families 0x10 and 0x11 (the latter just
for completeness, I have nothing to verify this against).
At the same time, provide a way to make these entries visible via the
'mce=bootlog' command line option even on these machines.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There apparently was an unnoticed conflict between an earlier patch to
this file and mine (d1e084746b), which
I noticed only now. I suppose a change like the one below (untested) is
needed; I didn't get any response on a confirmation request for this from
the submitter of the first patch.
The issue is the writing of the 'checkbit' member at the end of
setup_intel_arch_watchdog(), which my patch made go to intel_arch_wd_ops
rather than wd_ops.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
* Modify sched_affinity functions to pass cpumask_t variables by reference
instead of by value.
* Use new set_cpus_allowed_ptr function.
Depends on:
[sched-devel]: sched: add new set_cpus_allowed_ptr function
Cc: Paul Jackson <pj@sgi.com>
Cc: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Use new set_cpus_allowed_ptr() function added by previous patch,
which instead of passing the "newly allowed cpus" cpumask_t arg
by value, pass it by pointer:
-int set_cpus_allowed(struct task_struct *p, cpumask_t new_mask)
+int set_cpus_allowed_ptr(struct task_struct *p, const cpumask_t *new_mask)
* Cleanup uses of CPU_MASK_ALL.
* Collapse other NR_CPUS changes to arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.c
Use pointers to cpumask_t arguments whenever possible.
Depends on:
[sched-devel]: sched: add new set_cpus_allowed_ptr function
Cc: Len Brown <len.brown@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Change the following static arrays sized by NR_CPUS to
per_cpu data variables:
_cpuid4_info *cpuid4_info[NR_CPUS];
_index_kobject *index_kobject[NR_CPUS];
kobject * cache_kobject[NR_CPUS];
* Remove the local NR_CPUS array with a kmalloc'd region in
show_shared_cpu_map().
Also some minor complaints from checkpatch.pl fixed.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove old comments that include the old arch/i386 directory.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
make known_pat_cpu to think amd k8 and fam10h is ok too.
also make tom2 below to be WRBACK
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sets up pat_init() infrastructure.
PAT MSR has following setting.
PAT
|PCD
||PWT
|||
000 WB _PAGE_CACHE_WB
001 WC _PAGE_CACHE_WC
010 UC- _PAGE_CACHE_UC_MINUS
011 UC _PAGE_CACHE_UC
We are effectively changing WT from boot time setting to WC.
UC_MINUS is used to provide backward compatibility to existing /dev/mem
users(X).
reserve_memtype and free_memtype are new interfaces for maintaining alias-free
mapping. It is currently implemented in a simple way with a linked list and
not optimized. reserve and free tracks the effective memory type, as a result
of PAT and MTRR setting rather than what is actually requested in PAT.
pat_init piggy backs on mtrr_init as the rules for setting both pat and mtrr
are same.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
store initial_apicid from early identify. it is could be different from
phys_proc_id later.
also print it out in /proc/cpuinfo.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
