Add OneNAND Sync. Burst Read support
Tested with OMAP platform
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
OneNAND is a new flash technology from Samsung with integrated SRAM
buffers and logic interface.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The bit mask used for oob size calculation was using 2 bits instead
of one. Fortunately the next bit has been 0 all the time.
Thanks to Nathan H. for pointing this out
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While this might be useful for all supported flash types, it is mandatory
for proper JFFS2 support with Sibley flash.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This updates the Primary Vendor-Specific Extended Query parsing to
version 1.4 in order to get the information about the Configurable
Programming Mode regions implemented in the Sibley flash, as well as
selecting the appropriate write command code.
This flash does not behave like traditional NOR flash when writing data.
While mtdblock should just work, further changes are needed for JFFS2 use.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This includes improved error handling/reporting plus some other
message cleanups.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This type of flash translation layer (FTL) is used by the Embedded BIOS
by General Software. It is known as the Resident Flash Disk (RFD), see:
http://www.gensw.com/pages/prod/bios/rfd.htm
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch creates a file airo.h containing prototypes of the global
functions in airo.c used by airo_cs.c .
If you got strange problems with either airo_cs devices or in any other
completely unrelated part of the kernel shortly or long after a airo_cs
device was detected by the kernel, this might have been caused by the
fact that caller and callee disagreed regarding the size of the first
argument to init_airo_card()...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refine bnx2_poll() logic to write back the most up-to-date status tag
when all work has been processed. This eliminates some occasional
extra interrupts when a older status tag is written even though all
work has been processed.
The idea is to read the status tag just before exiting bnx2_poll() and
then check again for any new work. If no new work is pending, the
status tag written back will not generate any extra interrupt. This
logic is similar to the changes David Miller did to tg3_poll().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically determine the shared memory location where eeprom
parameters are stored instead of using a fixed location.
Add speed reporting to management firmware. This allows management
firmware to know the current speed without contending for MII
registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update bnx2 nvram code with support for 5708.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 5708 copper and serdes basic support, including 2.5 Gbps support
on 5708 serdes. SPEED_2500 is also added to ethtool.h
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch I sent in ("prism54: Free skb after disabling
interrupts") included a redundant NULL assignment. Thanks to Herbert
Xu for pointing it out.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems dmascc_setup() is a leftover time before dmascc_init() was
there.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 the following unused global functions:
- e1000_hw.c: e1000_mc_addr_list_update
- e1000_hw.c: e1000_read_reg_io
- e1000_hw.c: e1000_enable_pciex_master
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some visually impaired people use hardware devices which directly read
the vga screen. When newt for instance asks to hide the cursor for
better visual aspect, the kernel puts the vga cursor out of the screen,
so that the cursor position can't be read by the hardware device. This
is a great loss for such people.
Here is a patch which uses the same technique as CUR_NONE for hiding the
cursor while still moving it.
Mario, you should apply it to the speakup kernel for access floppies
asap. I'll submit a 2.4 patch too.
Signed-off-by: samuel.thibault@ens-lyon.org
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Statically allocated devices in module data is a potential cause
of oopsen. The device may be in use by a userspace process, which
will keep a reference to the device. If the module is unloaded,
the module data will be freed. Subsequent use of the platform
device will cause a kernel oops.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Statically allocated devices in module data is a potential cause
of oopsen. The device may be in use by a userspace process, which
will keep a reference to the device. If the module is unloaded,
the module data will be freed. Subsequent use of the platform
device will cause a kernel oops.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Re-jig the simple platform device support to allow private data
to be attached to a platform device, as well as allowing the
parent device to be set.
Example usage:
pdev = platform_device_alloc("mydev", id);
if (pdev) {
err = platform_device_add_resources(pdev, &resources,
ARRAY_SIZE(resources));
if (err == 0)
err = platform_device_add_data(pdev, &platform_data,
sizeof(platform_data));
if (err == 0)
err = platform_device_add(pdev);
} else {
err = -ENOMEM;
}
if (err)
platform_device_put(pdev);
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds a phy_mask field to struct mii_bus and uses it. This field
indicates each phy address to be ignored when probing the mdio bus.
This support is needed for the fs_enet and ibm_emac drivers to be
converted to the generic phy layer among other drivers. Many systems
lock up on probing certain phy addresses or probing doesn't return
0xffff when nothing is found at the address. A new driver I'm
working on also makes use of this mask.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some boards using the 79c976 pcnet32 chip will hang the system if the
ethtool --register-dump is performed with the device operational. The
request to read bcr30 is retried by the PCI device infinitely without
returning data, hanging the system.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch is a better fix for Allied Telesyn 2700/2701 FX boards than
the change made in early January this year. It allows the user to
select the speed/duplex via module_param, but if no selection is made,
forces the speed to 100 FD. It fixes both Bugzilla bugs 2669 and 4551.
Tested ia32 and ppc64 by myself, and by the originator of bug 2669.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Display the name eth%d or pci_name() of device which fails to allocate
memory. When changing ring size via ethtool, it also releases the
lock before returning on error. Added comment that the caller of
pcnet32_alloc_ring must call pcnet32_free_ring on error, to avoid leak.
Tested ia32 by forcing allocation errors.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides dynamic two buffer-mode and 3 buffer-mode options.
Previously 2 buffer-mode was compilation option. Now with this patch applied
one can load driver in 2 buffer-mode with module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=2
This patch also provides 3 buffer-mode which provides header separation
functionality. In 3 buffer-mode skb->data will have L2/L3/L4 headers and
"skb_shinfo(skb)->frag_list->data" will have have L4 payload.
one can load driver in 3 buffer-mode with same above module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=3
Please review the patch.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
fid is declared as a u32 (unsigned int), and then a few lines later, it is checked for a value < 0, which is clearly useless.
In the two locations this function is used, in one it is *explicitly* given a negative number, which would be ignored with the
current definition.
Thanks to LinuxICC (http://linuxicc.sf.net).
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Currently the driver takes a reference only for requests coming by way
of the gendisk, not for requests coming by way of the struct device or
struct scsi_device. Such requests can arrive in the rescan, flush,
and shutdown pathways.
The patch also makes the scsi_disk keep a reference to the underlying
scsi_device, and it erases the scsi_device's pointer to the scsi_disk
when the scsi_device is removed (since the pointer should no longer be
used).
This resolves Bugzilla entry #5237.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The printks that aren't for debugging should use the name of the controller,
not the driver name. Multiple MMC controllers aren't that common today, but
this is the right way to do things.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a broken if clause in the wbsd driver that can cause the
driver to try and configure the chip even though none is found. This
results in i/o on invalid ports.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use ata_pad_{alloc,free} in two drivers, to factor out common code.
Add ata_pad_{alloc,free} to two other drivers, which needed the padding
but had not been updated.
This adds support for the Nvidia Geforce 7800 series of cards to the
nvidiafb framebuffer driver. All it does is add the PCI device id for
the 7800, 7800 GTX, 7800 GO, and 7800 GTX GO cards to the module device
table for the nvidiafb.ko driver, so that nvidiafb.ko will actually work
on these cards.
I also added the relevant PCI device ids to linux/pci_ids.h
I tested it on my 7800 GTX here and it works like a charm. I now can
get framebuffer support on this card! Woo hoo!! Nothing like 200x75 text
mode to make your eyes BLEED. ;)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At header fixup time, it is not yet legal to ioremap() PCI
device registers, yet that is what this quirk code needs to
do.
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/block/ is right now a mix of core and driver parts. Lets move
the core parts to a new top level directory. Al will move the fs/
related block parts to block/ next.
Signed-off-by: Jens Axboe <axboe@suse.de>
Make sure that the P_Key index passed into mthca_modify_qp() is
within the device's P_Key table.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix sparse warning about passing `0` to simple_strtoul()
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix hotplug of devices for ib_umad module: when a device goes away,
kill off all MAD agents for open files associated with that device,
and make sure that the device is not touched again after ib_umad
returns from its remove_one function.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mellanox has decided that the components of the firmware version are
really meant to be displayed in decimal, e.g. 0x000400070190 is
version 4.7.400. Change the format we use from "%x.%x.%x" to
"%d.%d.%d" to match this convention.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't build ipoib_mcast_iter_ functions if CONFIG_INFINIBAND_IPOIB_DEBUG
is not enabled -- their only callers will not be built either.
Also move the prototype for ipoib_open() to ipoib.h to fix a sparse warning.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* Hide debugging code into #ifdef, which allows to simplify
the large switch statement
* Update macros to not reference variables not given as
arguments
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not register statically allocated input devices to prevent
OOPS when attaching input interfaces since it requires class
device to be properly initialized.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add an InfiniBand SCSI RDMA Protocol (SRP) initiator. This driver is
used to talk talk to InfiniBand SRP targets (storage devices).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Shrink our source and .text a little by removing a few assignments of
NULL and 0 to memory that is already cleared as part of the allocation.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace kmalloc()+memset(,0,) with kzalloc(), for a net savings of 35
source lines and about 500 bytes of text.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cfq's add_req_fn callback may invoke q->request_fn directly and
depending on low-level driver used and timing, a queued request may be
finished & deallocated before add_req_fn callback returns. So,
__elv_add_request must not access rq after it's passed to add_req_fn
callback.
This patch moves rq_mergeable test above add_req_fn(). This may
result in q->last_merge pointing to REQ_NOMERGE request if add_req_fn
callback sets it but as RQ_NOMERGE is checked again when blk layer
actually tries to merge requests, this does not cause any problem.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a panic in the current tree caused by a race condition between the initial replenish cycle and the rx processing of the first packets trying to replenish the buffers.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/char/tlclk.c: In function `tlclk_init':
drivers/char/tlclk.c:775: warning: implicit declaration of function `platform_device_register_simple'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CC drivers/char/tpm/tpm_nsc.o
drivers/char/tpm/tpm_nsc.c:277: error: `platform_bus_type' undeclared here (not in a function)
...
CC drivers/char/tpm/tpm_atmel.o
drivers/char/tpm/tpm_atmel.c:175: error: `platform_bus_type' undeclared here (not in a function)
Make sure to include proper headers.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were getting powerbook sleep code included, and giving compile
errors, with CONFIG_PM=y on a 64-bit build. This excludes that code
so the kernel will compile. One day BenH will implement on sleep on
the G5...
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Dan Williams
* If request_irq fails then a call to release_mem_region will be made with an invalid pointer.
* Two formatting fixes
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialise the .owner field of the device driver
with the module that owns it, for easier tracking
of device driver ownership. (probably also better
for sysfs...)
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The most trivial typo fix in the world.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Signed-off-by: Pdraig Brady <P@draigBrady.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Initialise the .owner field of the device driver
with the module that owns it, for easier tracking
of device driver ownership.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).
Signed-off-by: Jens Axboe <axboe@suse.de>
Right now we do it at queueing time, which works alright for reads
(since they are usually sync), but not for async writes since we can
queue io a lot faster than we can complete it. This makes the vmstat
output look extremely bursty.
Signed-off-by: Jens Axboe <axboe@suse.de>
The USB "handoff" code is an early PCI quirk to make sure we own the USB
controller (as opposed to the BIOS/SMM). But if the controller isn't
even enabled yet, don't try to access it.
Acked-by: Paul Mackerras <paulus@samba.org> (who had an alternate patch)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If I/O is active on the adapter, and an unexpected interrupt is pending
during initialization, the driver blows it's brains out. Since the driver
didn't initiate the I/O, the data in it's internal tables will contain NULL
pointers.
When this condition is detected, a "flush cache and reset" is performed.
The flush cache allows any pending "lazy writes" that the adapter is
processing to complete ( a "must have" for a RAID adapter ) and the reset
puts the adapter back into a known, good state.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jeff Garzik <jgarzik@pobox.com> points out that this was wrong: we need to
disable local interrupts while holding KM_IRQ0 due to IRQ sharing.
And holding interrupts off during a big PIO opration is expensive, so we only
want to do that if we know the page was highmem.
So revert commit 17fd47ab4d
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PC is left-over cruft after the introduction of CONFIG_X86_PC with
the subarch split. Remove it, and fixup the remaining users to depend on
CONFIG_X86_PC instead.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tejun Heo notes:
"I'm currently debugging this. The problem is that we are using the
generic dispatch queue directly in the noop sched and merging is NOT
allowed on dispatch queues but generic handling of last_merge tries
to merge requests. I'm still trying to verify this, so I'll be back
with results soon."
In the meantime, disable merging for noop by setting REQ_NOMERGE in
elevator_noop_add_request().
Eventually, we should add a noop_list and do the dispatching like in the
other io schedulers. Merging is still beneficial for noop (and it has
always done it).
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't clear ->elevator_data on exit, if we are switching queues we are
overwriting the data of the new io scheduler.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor cleanups: fix a misleading comment, and get rid of attr_mask
variables that are only used to hold constants (just use the constants
directly).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix wqe_to_link() to use a structure field that we know is definitely
always unused for receive work requests, so that it really avoids the
free list corruption bug that the comment claims it does.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace CQs that have no completion event channel attached end up
with their cq_context set to NULL. However, asynchronous events like
"CQ overrun" can still occur on such CQs, so add a uverbs_file member
to struct ib_ucq_object that we can follow to deliver these events.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Folk seem to get confused when they see two or more ttyS0 ports
appearing at boot time. One comes from the legacy table, and
one from PNP.
Hence, display the bus ID of the device which supplied the port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The problem is that adbhid[]->input is NULL, so the kernel oopses with
a null pointer dereference as soon as a key is pressed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A lot of power packed into a little patch.
This change eliminates the sharing between our controller-wide spinlock
and the SCSI core's Scsi_Host lock. As the locking in libata was
already highly compartmentalized, always referencing our own lock, and
never scsi_host::host_lock.
As a side effect, this change eliminates a deadlock from calling
scsi_finish_command() while inside our spinlock.
Integrate ata_exec() and ata_tf_to_host() into their only caller,
ata_bus_edd().
Rename ata_tf_to_host_nolock() to ata_tf_to_host().
This makes locking a bit easier to review, and may help pave the way for
future changes.
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Use kzalloc() instead of kmalloc + memset.
- Clean/fix some printk's.
- Use NULL for pointers instead of 0.
- Combine hpet busy searching locations into a function call.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Use HPET physical address to detect duplicates, not logical addresses.
Using logical (mapped) addresses fails to detect duplicates
because ioremap() returns a new mapped address each time.
- iounmap() regions when duplicate/busy areas are found.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the ACPI HPET description table to use a resource type of FIXED_MEM32
for the HPET reource. Use the fixed resoure size of 1 KB for the HPET
resource as per the HPET spec.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When booting, display the timer frequency in Hertz instead of as tick length
in nanoseconds. Apart from saving a local variable, this makes the message
more easily comprehensible.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the hpet_ioctl_common() function, devp->hd_hpets is already cached in the
hpetp variable, so we can use just that.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix two instances where a function would access the first HPET device instead
of the current one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clear the ht_opaque field in the hpet_register() function before searching for
a free timer to prevent the function from incorrectly assuming that the search
succeeded afterwards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a division by zero that happened when the HPET_INFO ioctl was called
before a timer frequency had been set.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a wrong memory access in hpet_ioctl_common(). It was not possible to use
the HPET_INFO ioctl from kernel space because it always called copy_to_user().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for shared HPET interrupts.
The driver previously acknowledged interrupts for both edge and level
interrupts, but didn't actually allow a shared interrupt in the latter case.
We use a new per-timer flag to save whether the timer's interrupt might be
shared, and use it to do the processing required for level interrupts only if
necessary.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was only the RTC hardware that restricted interrupt frequencies to a power
of two. There is no reason to take over this restriction into the HPET
driver, so remove the offending check.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes several reads of a timer's config register that serve no
purpose whatsoever.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The variable hpet_ntimer is never read, so remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On 32-bit architectures, the multiplication in the argument for
hpet_time_div() often overflows. In the typical case of a 14.32 MHz timer,
this happens when the desired frequency exceeds 61 Hz.
To avoid this multiplication, we can precompute and store the hardware
timer frequency, instead of the period, in the device structure, which
leaves us with a simple division when computing the number of timer ticks.
As a side effect, this also removes a theoretical bug where the timer
interpolator's frequency would be computed as a 32-bit value even if the
HPET frequency is greater than 2^32 Hz (the HPET spec allows up to 10 GHz).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disallow setting an interrupt frequency of zero (which would result in a
division by zero), and disallow enabling the interrupt when the frequency
hasn't yet been set (which would use an interrupt period of zero).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the remaining "Using plain integer as NULL pointer" sparse
warnings to use NULL. (Not duplicating patches that are already in -mm,
-bird, or -kj.)
Convert isdn driver struct initializer to use C99 syntax.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Various whitespace fixes
- Use kzalloc()
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the Infineon TPM driver off pci device and makes it a pure pnp-driver.
It includes pnp-port validation and region requesting.
Signed-off-by: Marcel Selhorst <selhorst@crypto.rub.de>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the nsc driver from a pci driver to a platform driver.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the atmel driver from a pci driver to a platform driver.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is in support of moving away from the lpc bus pci_dev. The power
management prototypes used by platform drivers is different but the
functionality remains the same.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the tpm does not have it's own pci id we have been consuming the lpc
bus. This is not correct and causes problems to support non lpc bus chips.
This patch removes the dependency on pci_dev from tpm.c The subsequent patches
will stop the supported chips from registering as pci drivers.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is in preparation of supporting chips that are not necessarily on
the lpc bus and thus are not accessed with inb's and outb's. The patch
replaces the call to get the chip's status in the tpm.c file with a vendor
specific status function. The patch also defines the function for each of the
current supported devices.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's nasty to set random drivers to default m because people who just press
enter on make oldconfig get these. Remove the default m
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver had incorrectly wrapped module_init(rp_init) in #ifdef MODULE,
so it worked only when compiled as a module.
Tested by Wolfgang Denk with this device:
00:0e.0 Communication controller: Comtrol Corporation RocketPort 8 port w/RJ11 connectors (rev 04)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 7000 [size=64]
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a long-standing vgacon bug: characters with the bright bit
set were left on the screen and not blacked out. All I did was that I
lookuped up some examples on the net about setting the vga palette, and
added the call missing from the linux kernel, but included in all other
ones. It works for me.
You can test this by writing something with the bright set to the
console, for example:
echo -e "\e[1;31mhello there\e[0m"
and then wait for the console to blank itself (by default, after 10 mins
of inactivity), maybe making it faster using
setterm -blank 1
so you only have to wait 1 minute.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because people can play games reprogramming keys and leaving traps for the
next user of the console.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert existing function docs to kernel-doc format. Eliminate all
kernel-doc warnings. Fix some doc typos and a little whitespace cleanup.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added a Receive_Abort to the Marvell serial driver
Fix occasional input overrun errors on Marvell serial driver
- If the Marvell serial driver is repeatedly started and then stopped it
will occasionally report an input overrun error when started.
- Added a Receive_Abort to the Marvell serial driver to abort previously
received receive errors when re-starting the receive
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Carlos Sanchez <csanchez@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various small mods for the Altix ioc4 serial driver - mostly cleanup:
- remove UIF_INITIALIZED usage
- use the 'lock' from uart_port
- better multiple card support
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove some unneeded casts.
Avoid an assignment in the case of kmalloc failure.
Break a few instances of if (foo) whatever; into two lines.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the requested I/O scheduler is already in place, elevator_switch simply
leaves the queue alone, and returns. However, it forgets to call
elevator_put, so
'echo [current_sched] > /sys/block/[dev]/queue/scheduler'
will leak a reference, causing the current_sched module to be permanently
pinned in memory.
Signed-off-by: Nate Diller <nate@namesys.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typo fix: dots appearing after a newline in printk strings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(akpm: I don't do typo patches, but one of these is in a printk string)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a kconfig submenu to select the default I/O scheduler, in case
anticipatory is not compiled in or another default is preferred. Also,
since no-op is always available, we should use it whenever the selected
default is not.
Signed-off-by: Nate Diller <nate@namesys.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that RCU applied on 'struct file' seems stable, we can place f_rcuhead
in a memory location that is not anymore used at call_rcu(&f->f_rcuhead,
file_free_rcu) time, to reduce the size of this critical kernel object.
The trick I used is to move f_rcuhead and f_list in an union called f_u
The callers are changed so that f_rcuhead becomes f_u.fu_rcuhead and f_list
becomes f_u.f_list
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only call to ide_cdrom_capacity is in code protected by
CONFIG_PROC_FS, so when that is not enabled, the compiler complains:
drivers/ide/ide-cd.c:3259: warning: `ide_cdrom_capacity' defined but not used
Here is a patch that fixes that. It provides some space savings for
embedded systems that are not using procfs, as well:
text data bss dec hex filename
- 33540 6504 1032 41076 a074 drivers/ide/ide-cd.o
+ 33468 6480 1032 40980 a014 drivers/ide/ide-cd.o
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some more references to check_region().
I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git
The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c
Remove last vestiges of ide_check_region()
drivers/char/specialix: trim trailing whitespace
drivers/char/specialix: eliminate use of check_region()
Remove outdated and unused references to check_region()
[sound oss] remove check_region() usage from cs4232, wavfront
[netdrvr eepro] trim trailing whitespace
[netdrvr eepro] remove check_region() usage
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last patch from Jens Axboe for drivers/block/paride/pf.c introduced
pf_end_request() which sets pf_req to NULL.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We're trying to get rid of as much as possible tasklist walks, or at
least moving them to core code. This patch falls into the second
category.
Instead of walking the tasklist in cfq-iosched move that into
elv_unregister. The added benefit is that with this change the as
ioscheduler might be might unloadable more easily aswell.
The new code uses read_lock instead of read_lock_irq because the
tasklist_lock only needs irq disabling for writers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
smsc-ircc2 - avoid closing network device when suspending; just release
interrupt and disable DMA ourselves. Also make sure to reset chip when
resuming.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Tourrilhes <jt@bougret.hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's not necessary to test PageHighmem in here - kmap_atomic() does the right
thing.
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch exports modalias for ccw devices.
So you can do:
modprobe `echo /sys/device/path_to_device/modalias`
and the proper driver will automatically be loaded by userspace.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix fullscreen view of the 3270 device driver.
Signed-off-by: Richard Hitt <rbh00@utsglobal.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update SMC91x driver for m32r.
- Remove needless NONCACHE_OFFSET adjustment.
> [PATCH 2.6.14-rc4] m32r: NONCACHE_OFFSET in _port2addr
> Change _port2addr() not to add NONCACHE_OFFSET.
> Adding NONCACHE_OFFSET requires needless address adjusting by a driver
> using ioremap() like a SMC91x driver.
- Fix lots of warnings as following:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c: In function `smc_reset':
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:324: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:325: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:341: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:342: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add pm_ops.valid callback, so only the available pm states show in
/sys/power/state. And this also makes an earlier states error report at
enter_state before we do actual suspend/resume.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Acked-by: Pavel Machek<pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpufreq entries in sysfs should only be populated when CPU is online state.
When we either boot with maxcpus=x and then boot the other cpus by echoing
to sysfs online file, these entries should be created and destroyed when
CPU_DEAD is notified. Same treatement as cache entries under sysfs.
We place the processor in the lowest frequency, so hw managed P-State
transitions can still work on the other threads to save power.
Primary goal was to just make these directories appear/disapper dynamically.
There is one in this patch i had to do, which i really dont like myself but
probably best if someone handling the cpufreq infrastructure could give
this code right treatment if this is not acceptable. I guess its probably
good for the first cut.
- Converting lock_cpu_hotplug()/unlock_cpu_hotplug() to disable/enable preempt.
The locking was smack in the middle of the notification path, when the
hotplug is already holding the lock. I tried another solution to avoid this
so avoid taking locks if we know we are from notification path. The solution
was getting very ugly and i decided this was probably good for this iteration
until someone who understands cpufreq could do a better job than me.
(akpm: export cpucontrol to GPL modules: drivers/cpufreq/cpufreq_stats.c now
does lock_cpu_hotplug())
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpu_sys_devices is redundant with the new API get_cpu_sysdev(). So nuking
this usage since its not needed.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some modules creating sysfs entries under /sys/devices/system/cpu/cpuX/
need to know the parent sysfs entry to make devices under them. This will
just return the sysfs entry for a given cpu.
sysfs entries showing under each cpu sysfs can be easily created if such
entries can be created by registering a sysfs driver for cpuclass. The
issue is when the entry is created the CPU may not be online, hence we
would need to defer the creation until the online notification comes.
Current users: cache entries for Intel CPU's and cpufreq subsystem.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for pcmcia slot on sharp zaurus sl-5500.
pxa2xx_sharpsl.c thus becomes quite miss-named, but I guess that
is not worth fixing?
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for sharp zaurus sl-5500 touchscreen. It introduces
some not-too-nice ifs, but I guess copying whole ucb1x00-ts.c would be
bad idea...
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes an issue reported by Coverity in serial/serial_core.c
Error reported: Variable "&((info)->tty)->flags" tracked as NULL was passed to a
function that dereferences it.
The later statements in the function assumes 'info->tty != NULL', so this
check is not necessary. Probably a 'BUG_ON(info->tty == NULL)' can be added.
Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the IMX serial driver to unregister its driver structure
when it is unloaded.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Richard Purdie
Update the PXA irda driver to match the recent platform device
suspend/resume level changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ata_pci_init_one() receives an array of struct ata_port_info. Recent
updates to the code had always obtained port information from
array element 0, rather than array element N.
Change to avoid hardcoding port_info[0], thereby restoring proper
hardware information to secondary legacy ports.
If a card doesn't support the "write block" command class then
any attempts to open the device should reflect this by denying
write access.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
This basically keeps up from having to extern __kmalloc_section_memmap().
The vaddr_in_vmalloc_area() helper could go in a vmalloc header, but that
header gets hard to work with, because it needs some arch-specific macros.
Just stick it in here for now, instead of creating another header.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Lion Vollnhals <webmaster@schiggl.de>
Signed-off-by: Jiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds generic memory add/remove and supporting functions for memory
hotplug into a new file as well as a memory hotplug kernel config option.
Individual architecture patches will follow.
For now, disable memory hotplug when swsusp is enabled. There's a lot of
churn there right now. We'll fix it up properly once it calms down.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove PageReserved() calls from core code by tightening VM_RESERVED
handling in mm/ to cover PageReserved functionality.
PageReserved special casing is removed from get_page and put_page.
All setting and clearing of PageReserved is retained, and it is now flagged
in the page_alloc checks to help ensure we don't introduce any refcount
based freeing of Reserved pages.
MAP_PRIVATE, PROT_WRITE of VM_RESERVED regions is tentatively being
deprecated. We never completely handled it correctly anyway, and is be
reintroduced in future if required (Hugh has a proof of concept).
Once PageReserved() calls are removed from kernel/power/swsusp.c, and all
arch/ and driver code, the Set and Clear calls, and the PG_reserved bit can
be trivially removed.
Last real user of PageReserved is swsusp, which uses PageReserved to
determine whether a struct page points to valid memory or not. This still
needs to be addressed (a generic page_is_ram() should work).
A last caveat: the ZERO_PAGE is now refcounted and managed with rmap (and
thus mapcounted and count towards shared rss). These writes to the struct
page could cause excessive cacheline bouncing on big systems. There are a
number of ways this could be addressed if it is an issue.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Refcount bug fix for filemap_xip.c
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch rewrites various occurences of &sg[0] where sg is an array
of length one to simply sg.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch uses sg_set_buf/sg_init_one in some places where it was
duplicated.
Signed-off-by: David Hardeman <david@2gen.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The following patch removes the dependency of the fec_8xx driver on
the NETTA & NETPHONE boards. Other people use the driver too, and
we await their board support patches.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patches fixes a bug with erroneous calling of
dma_unmap_single. It never triggered because on normal ppc32
the calls is a NOP. Out of tree drivers need this fix however.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* MII registers must override strap pins
* disable "echo" mode to make 10/HDX work (Franz Sirl)
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For some reason, the hardware designers made the polarity of one bit
in the 440SPe's PHY interface register the opposite of all other PPC
440 chips. To handle this, abstract our access to this bit and do the
right thing based on the configured CPU type.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use spin_trylock_irqsave() in ipoib_start_xmit() instead of
reinventing it out of local_irq_save(), spin_trylock() and
local_irq_restore().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- converted to platform bus
- removed pci dependencies
- removed virt_to_phys/phys_to_virt calls
System now can root off of a disk.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/Documentation/mips/AU1xxx_IDE.README b/Documentation/mips/AU1xxx_IDE.README
new file mode 100644
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The dev_kfree_skb in islpci_eth_transmit happens while irqs are still
disabled, so either dev_kfree_skb_irq needs to be used or the skb
needs to be freed after irqs have been enabled again. This patch
should fix it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
