This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP
board file supports only minimal set of drivers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for keypad, GPIO keys and LEDs. Also enable hardware
debounce feature for GPIO keys.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup regulators for MMC1 and MMC2 to get those SD slots
working again.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
CC: David Brownell <david-b@pacbell.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize regulators for Beagle and Overo.
Patch is based on earlier patches posted to linux-omap mailing
list.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Stanley.Miao <stanley.miao@windriver.com>
with board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Qimonda HYB18M512160AF-6 SDRAM chip, used on
the OMAP3430SDP boards.
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chip used on 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards. Original timing data is from the Micron
datasheet PDF downloaded from:
http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move platform_device_register() for serial device to
omap_serial_init()
There is no need to have arch_initcall() dependency in serial
as already board files call the function omap_serial_init()
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Hunyue Yau <hyau@mvista.com> with
board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Hunyue Yau <hyau@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert the board-rx51 smc91x code to be generic and make
the boards to use it. This allows future recalculation of the
timings when the source clock gets scaled.
Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL.
Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing
calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add generic onenand support when connected to GPMC and make the
boards to use it.
The patch has been modified to make it more generic to support all
the boards with GPMC. The patch also remove unused prototype for
omap2_onenand_rephase(void).
Note that board-apollon.c is currently using the MTD_ONENAND_GENERIC
and setting the GPMC timings in the bootloader. Setting the GPMC
timings in the bootloader will not allow supporting frequency
scaling for the onenand source clock.
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.
Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes it possible to change uart sleep timeout. New sysfs
entry is added (/sys/devices/platform/serial8250.<uart>/sleep_timeout)
Writing zero will disable the timeout feature and prevent UART clocks
from being disabled.
Also default timeout is increased to 5 second to make serial console
more usable.
Original patch was written by Tero Kristo.
Cc: Tero Kristo <Tero.Kristo@nokia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention. The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup. The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.
While the activity timer is active, the smart-idle mode of the UART is
also disabled. This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.
Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.
In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.
Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.
Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add common omap2/3 function to check wether there is irq pending.
Switch to use it in omap2 pm code instead of its own.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 5461af5af5.
Adding a disable hook to the irq_chip is not the way to fix the
problem being addressed by this patch. Instead, we need to fix
support for [enable|disable]_irq_wake().
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently "tidspbridge" driver uses its own mmu implementation and
will migrate to use this "omap iommu" eventually. This config is
provided to make this migration happen smoothly.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This makes the framebuffer work on omap3.
Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".
Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.
This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On our system we see the following messages:
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...
The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.
Let's give them debugging level instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages. Same with
omap2_clksel_round_rate_div(). While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz. CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations. Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Renumber registers in omap3_sram_configure_core_dpll() assembly code to
make space for additional parameters.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialize SDRC_POWER to a known-good setting when the kernel boots.
Necessary since some bootloaders don't initialize SDRC_POWER properly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Clear the SDRC_POWER.PWRENA bit before putting the SDRAM into self-refresh
mode. This prevents the SDRC from attempting to power off the SDRAM,
which can cause the system to hang.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add more barriers in the SRAM CORE DPLL M2 divider change code.
- Add a DSB SY after the function's entry point to flush all cached
and buffered writes and wait for the interconnect to claim that they
have completed[1]. The idea here is to force all delayed write
traffic going to the SDRAM to at least post to the L3 interconnect
before continuing. If these writes are allowed to occur after the
SDRC is idled, the writes will not be acknowledged and the ARM will
stall.
Note that in this case, it does not matter if the writes actually
complete to the SDRAM - it is only necessary for the writes to leave
the ARM itself. If the writes are posted by the interconnect when
the SDRC goes into idle, the writes will be delayed until the SDRC
returns from idle[2]. If the SDRC is in the middle of a write when
it is requested to enter idle, the SDRC will not acknowledge the
idle request until the writes complete to the SDRAM.[3]
The old-style DMB in sdram_in_selfrefresh is now superfluous, so,
remove it.
- Add an ISB before the function's exit point to prevent the ARM from
speculatively executing into SDRAM before the SDRAM is enabled[4].
...
1. ARMv7 ARM (DDI 0406A) A3-47, A3-48.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
3. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
4. ARMv7 ARM (DDI 0406A) A3-48.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
With the clkdev, musb_core.c needs to register clock with name "ick".
Once all the platforms using the musb driver have been converted
to use clockdev, the clock name does not need to be passed
from the low-level init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
SPI driver will do unhandled fault on OMAP2420 if trying to probe
non-existing SPI busses. Register those additional busses runtime only
for cpus having them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "tusb6010 init error 5, -19" and compilation warning from function
tusb6010_platform_retime "warning: 'sysclk_ps' is used uninitialized in this
function".
I suppose commit c094ba34b8f780885d029ce3c2715a194b780e5d was meant to test
for zero fclk_ps instead of sysclk_ps.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO de-bounce clocks don't have any impact on the module idle state, so
the clock code should not wait for the module to enable after the de-bounce
clocks are enabled.
Problem found by Kevin Hilman <khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The structure 'arch_mmu' accommodates the difference between omap1 and
omap2/3.
This patch provides omap2/3 specific functions
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12. Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management. GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management. GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator. But on HS devices, it
may not be available for Linux use.
It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12.
This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.
Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.
Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
This patch avoids waiting for the camera module to become ready,
since it doesn't have IDLEST bit.
Based on a earlier hack done by Paul Walmsley on Sep 9 2008 on
linux-omap tree.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 8ad8ff6548 breaks the OMAP2xxx
cpu_mask code, which causes OMAP2xxx to panic on boot. Fix by
removing the cpu_mask auto variable and by changing CK_242X
and CK_243X to use RATE_IN_242X/RATE_IN_243X.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<1>pgd = c0004000
<1>[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #32)
PC is at omap2_clk_set_parent+0x104/0x120
LR is at omap2_clk_set_parent+0x28/0x120
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
SPURIOUSIRQ is contained in bits 31:7 of INTC_SIR, so
INTC_SIR must be right shifted by 7, not 6.
No change in logic, only changes for better readability.
Refer to register definition of INTCPS_SIR_IRQ in OMAP3 Manual.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In linus' git tree the functions can be found at:
vi arch/arm/mach-omap2/usb-tusb6010.c +200 - tusb6010_platform_retime()
vi arch/arm/mach-omap2/gpmc.c +94 - gpmc_get_fclk_period()
vi arch/arm/mach-omap2/usb-tusb6010.c +53 - tusb_set_async_mode()
vi arch/arm/mach-omap2/usb-tusb6010.c +111 - tusb_set_sync_mode()
is -ENODEV appropriate when sysclk_ps == 0?
This was found by code analysis, please review.
------------------------------>8-------------8<---------------------------------
gpmc_get_fclk_period() may return 0 when gpmc_l3_clk is not enabled. This is
not checked in tusb6010_platform_retime() nor in tusb_set_async_mode() it
seems. In tusb_set_sync_mode() this may result in a division by zero.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no anymore legacy driver for OMAP24XX Enhanced Audio Controller
in linux-omap and it was newer in mainline so cleanup these unneeded
defines and initialization code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3f0a820c4c breaks OMAP2xxx boot
during initial propagate_rate() on osc_ck and sys_ck. Fix by
pre-initializing all struct clks before running any other clock init
code. Incorporates review comments from Russell King
<rmk+kernel@arm.linux.org.uk>.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 00000000
<1>pgd = c0004000
<1>[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #37)
PC is at propagate_rate+0x10/0x60
LR is at omap2_clk_init+0x30/0x218
...
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gumstix will soon be shipping a variant of their Summit board that
includes an SMSC LAN9221 ethernet interface. This patch provides
support via the smsc911x driver when enabled in kernel config.
The Overo defconfig is not updated since the LAN9221 is an option
not present on all systems.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
from 2.6.29, smc911x isn't maintained anymore. A new driver, smsc911x,
will replace it. so convert omap_ldp to use smsc911x driver.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
This fixes a compile error caused by a mismerge while rebasing the patch:
linux-2.6/arch/arm/mach-omap2/board-rx51-peripherals.c:354:
undefined reference to `twl4030_mmc_init'
Looks like I need to also update my build scripts, just grepping for error:
in the logs is not obviously enough..
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds board files and related headers for Nokia RX-51
Internet Tablet.
This patch has been updated with some clean-up patches
posted earlier to linux-omap list.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for 3430 SDP.
Various updates have been merged into this patch from
the linux-omap list.
Patch updated to initialize regulators by David Brownell
<dbrownell@users.sourceforge.net>.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An upcoming Overo expansion board includes an ADS7846 touchscreen controller.
This patch adds support via the ads7846 driver when enabled in the
kernel config.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create a generic board-file for initializing usb
on omap2430 and omap3 boards.
Patch modified by Tony to build the module based on
CONFIG_USB_MUSB_SOC. Also merged in a patch adding
the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Resolve longstanding issue noted by Adrian Hunter: confusion
between settting VSEL=0 (which is 1.8V on MMC1) and poweroff.
Also, leave VSEL alone if we're just powering the regulator off.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device connected to MMC3 is assumed to be self-powered, so
set_power() function is empty. It can't be omited because
host driver requires it.
Array size for hsmmc[] is specified to allocate to allocate
an instance for the third MMC controller.
Also fix a leak which happens if invalid controller id
is passed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When setting up HSMMC devices, pass the device nodes back so
board code can linking them to their power supply regulators.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correct twl4030 MMC power switching: fix voltage ranges reported
for each slot, and handle them fully.
Lies corrected:
- MMC-1 doesn't support the 2.6-2.7 Volt range
- MMC-2 can't normally support anything except 1.8V
Omissions corrected
- MMC-1 *does* handle the 2.8-2.9 Volt range
- MMC-2 can handle 2.5-3.2 Volt cards, given a transceiver
Add transciever support for MMC-2; enable it for Overo and Pandora.
(Depends on something else to have set up pinmuxing for control
signals instead of as MMC2_DAT4..7 pins.)
Also shrink twl4030_hsmmc_info a smidgeon ... padding is all gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 1 to buffer length for null terminator and use snprintf.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds several new GPIO pins and updates
the pin naming comments.
The patch is based on earlier patches on linux-omap
list by Manikandan Pillai <mani.pillai@ti.com>,
Vaibhav Hiremath <hvaibhav@ti.com> and
David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no CONFIG_I2C2_OMAP_BEAGLE in mainline and it is under
removal in linux-omap also so remove this dead code now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.
For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.
Patch updated by Tony for mainline, basically make
n770 and h4 compile. Also folded in a fix for OSK
by David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP34XX_ETHR_START to LDP_ETHR_START.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP24XX_ETHR_GPIO_IRQ to H4_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
SDP2430_ETHR_GPIO_IRQ to SDP2430_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
