This driver has been mostly rewritten since Michael Brown's initial
work, so swap the order of the authors.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This integrates support for the SFC9000 family of 10G Ethernet
controllers and LAN-on-motherboard chips, starting with the SFL9021
'Siena' and SFC9020 'Bethpage'.
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the SFC9000 family of 10G Ethernet controllers
and LAN-on-motherboard chips, starting with the SFL9021 'Siena' and
SFC9020 'Bethpage'.
The SFC9000 family is based on the SFC4000 'Falcon' architecture, but
with some significant changes:
- Two ports are associated with two independent PCI functions
(except SFC9010)
- Integrated 10GBASE-T PHY(s) (SFL9021/9022)
- MAC, PHY and board peripherals are managed by firmware
- Driver does not require board-specific code
- Firmware supports wake-on-LAN and lights-out management through NC-SI
- IPv6 checksum offload and RSS
- Filtering by MAC address and VLAN (not included in this code)
- PCI SR-IOV (not included in this code)
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In new NICs flash is managed by firmware and we will use high-level
operations on partitions rather than direct SPI commands. Add support
for multiple MTD partitions per flash device and remove the direct
link between MTD and SPI devices. Maintain a list of MTD partitions
in struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs have firmware managing the PHY, and we will discover the PHY
capabilities at run-time. Replace the static data with probe() and
test_name() operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs and PHYs support a wider variety of loopback modes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_probe_nic_variant() does a lot less than it used to, and a
lot less than it claims to. Fold the remainder into its caller.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor efx_reset_down() and efx_reset_up() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-LAN is a stub for Falcon, but will be implemented fully for
new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the efx_nic_type::monitor operation or event handling as
appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor PHY, MAC and NIC configuration operations so that the
existing link configuration can be re-pushed with:
efx->phy_op->reconfigure(efx);
efx->mac_op->reconfigure(efx);
and a new configuration with:
efx->nic_op->reconfigure_port(efx);
(plus locking and error-checking).
We have not held the link settings in software (aside from flow
control), and have relied on asking the hardware what they are. This
is a problem because in some cases the hardware may no longer be in a
state to tell us. In particular, if an entire multi-port board is
reset through one port, the driver bindings to other ports have no
chance to save settings before recovering.
We only actually need to keep track of the autonegotiation settings,
so add an ethtool advertising mask to struct efx_nic, initialise it
in PHY init and update it as necessary.
Remove now-unneeded uses of efx_phy_op::{get,set}_settings() and
struct ethtool_cmd.
Much of this was done by Steve Hodgson <shodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation for adding differing implementations for new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause frame generation is gated by both RX_XOFF_MAC_EN and an enable
bit in each MAC. RX_XOFF_MAC_EN bit always reads back as 0 so we need
to set it correctly every time we modify RX_CFG_REG. Simplify this by
always setting it to 1 and only changing the enable bits in the MACs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register only needs to be written after reset, not each time we
enable interrupts.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'likely' hint to test of rx_checksum_enabled.
Don't count IP fragments; the IP stack can do that.
Do count non-matching multicast packets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "bug9141 workaround" of setting TX_FLUSH_MIN_LEN_EN should really
be considered as a normal bit of configuration rather than a
workaround.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strap bits are only important on Falcon A and all production
boards using it have fixed-speed 10G PHYs.
Replace dummy MAC operations with default MAC operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never use MDIO in atomic context, so we don't need to spin.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading standard registers on the QT2025C before its firmware has
booted may cause the boot process to fail. Therefore, follow the
recommended reset sequence before reading its id registers. Either
order works for the QT2022C2, so don't differentiate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Falcon can generate events for LASI interrupts from the PHY, but in
practice we have never implemented this in reference designs. Instead
we have polled, inserted the appropriate events, and then handled the
events later. This is a waste of time and code.
Instead, make PHY poll functions update the link state synchronously
and report whether it changed. We can still make use of the LASI
registers as a shortcut on the SFT9001.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Currently we can set multicast hash immediately (in atomic context)
but must delay setting MAC promiscuity. There is not that much
point in deferring one but not the other, and setting the multicast
hash on Siena will involve a firmware request. So process them
both in efx_mac_work().
Also, set the broadcast bit in the multicast hash in
efx_set_multicast_list(), since this is required for both Falcon and
Siena.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Only the XMAC on Falcon needs help from the driver to poll and reset
the MAC-PHY link (XAUI); GMII is a simple parallel bus and on later
NICs firmware takes care of the XAUI link. Also, an XMAC interrupt
currently schedules a work item which simply clears a flag
(efx_nic::mac_up) to be checked by the regular monitor (or the next
link reconfiguration, if that is sooner).
Rename the flag to xmac_poll_required, changing its sense. Remove the
needless indirection and just set the flag immediately. Call
falcon_xmac_poll() directly where required.
Add a new generic operation mac_op::check_fault to check the link
outside of regular monitoring, as required during self-tests.
(Note that this leaves us with an unused work item, but we will
immediately have another use for it.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Currently we initiate MAC stats DMA and busy-wait for completion when
stats are requested. We can improve on this with a periodic timer to
initiate and poll for stats, and opportunistically poll when stats are
requested.
Since efx_nic::stats_disable_count and efx_stats_{disable,enable}()
are Falcon-specific, rename them and move them accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although efx_init_port() is only called at probe time and so cannot
race with port reconfiguration, most of the functions it calls can
expect to be called with the MAC lock held.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid overrunning the hardware limit of 4 concurrent RX queue flushes.
Expand the queue flush state to support this. Make similar changes to
TX flushing to keep the code symmetric.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put all static information in struct falcon_board_type and replace it
with a pointer in struct falcon_board. Simplify probing aocordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although all the defined fields in these registers are within 32 bits,
they are architecturally defined as 128-bit like most other Falcon
registers. In particular, we must use efx_reado() to ensure proper
locking when reading MD_STAT_REG.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
