The DSCR (aka Data Stream Control Register) is supported on some
server PowerPC chips and allow some control over the prefetch
of data streams.
This patch allows the value to be specified per thread by emulating
the corresponding mfspr and mtspr instructions. Children of such
threads inherit the value. Other threads use a default value that
can be specified in sysfs - /sys/devices/system/cpu/dscr_default.
If a thread starts with non default value in the sysfs entry,
all children threads inherit this non default value even if
the sysfs value is changed later.
Signed-off-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we set up the TLB for ourselves on Book3E, we need to flush out any
old mappings established by the firmware or bootloader. At present we
attempt this with a tlbilx to flush everything, but this will leave behind
any entries with the IPROT bit set.
There are several good reason firmware might establish mappings with IPROT,
and in fact ePAPR compliant firmwares are required to establish their
initial mapped area with IPROT.
This patch, therefore adds more complex code to scan through the TLB upon
entry and flush away any entries that are not our own.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An erratum on A2 can lead to the bolted entry we insert for the linear
mapping being evicted, to avoid that write the bolted entry to way 3.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In exc_lvl_ctx_init() we index into the crit/dbg/mcheck stacks using
the hard cpu id, but that assumes the hard cpu id is zero based and
contiguous. That is not the case on A2.
The root of the problem is that the 32bit code has no equivalent of the
paca to allow it to do the hard->soft mapping in assembler. Until the
32bit code is updated to handle that, index the stacks using the soft
cpu ids on 64bit and hard on 32 bit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the cputable entry, regs and setup & restore entries for
the PowerPC A2 core.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As well as searching for nodes with type = "nvram", search for nodes
that have compatible = "nvram". This can't be converted into a single
call to of_find_compatible_node() with a non-NULL type, because that
searches for a node that has _both_ type & compatible = "nvram".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An upcoming new ics backend will need to implement different matching
semantics to the current ones, which are essentially the RTAS ics
backends. So move the current match into the RTAS backend, and allow
other ics backends to override.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SCOM is a side-band configuration bus implemented on some processors.
This code provides a way for code to map and operate on devices via
SCOM, while the details of how that is implemented is left up to a
SCOM "controller" in the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have platform code that needs to find a node's interrupt parent, so
export of_irq_find_parent() so we can use it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a few places we patch instructions without using
patch_instruction and patch_branch, probably because they
predated it. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we allocate the stale_map for a cpu when it comes online,
this leaves open a small window where a process can be scheduled
on the cpu before the stale_map is allocated. Instead allocate
the stale_map at CPU_UP_PREPARE time, that way it will be always
available before tasks start running.
It is possible the cpu fails to come up, in which case we should free
the stale_map, so add a CPU_UP_CANCELED case to do that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a first cut at making bootwrapper code which will
produce a zImage compliant with the requirements set down
by ePAPR.
This is a very simple bootwrapper, taking the device tree
blob supplied by the ePAPR boot program and passing it on
to the kernel. It builds on the earlier patch to build a
relocatable ET_DYN zImage to meet the other ePAPR image
requirements.
For good measure we have some paranoid checks which will
generate warnings if some of the ePAPR entry condition
guarantees are not met.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds code, linker script and makefile support to allow
building the zImage wrapper around the kernel as a position independent
executable. This results in an ET_DYN instead of an ET_EXEC ELF output
file, which can be loaded at any location by the firmware and will
process its own relocations to work correctly at the loaded address.
This is of interest particularly since the standard ePAPR image format
must be an ET_DYN (although this patch alone is not sufficient to
produce a fully ePAPR compliant boot image).
Note for now we don't enable building with -pie for anything.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On Book3E, MMU_NO_CONTEXT != 0, but the slice_mm_new_context()
macro assumes that it is. This means that the map of the
page sizes for each slice is always initialized to zeroes
(which happens to be 4k pages), rather than to the correct
default base page size value - which might be 64k.
This patch corrects the problem.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use MMU_NO_CONTEXT as the initialiser for mm_context.id on
nohash and hash64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to do that to guarantee they see any code change done by
dynamic patching during boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wakeup comes from the system reset handler with a potential loss of
the non-hypervisor CPU state. We save the non-volatile state on the
stack and a pointer to it in the PACA, which the system reset handler
uses to restore things
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to wait a bit for them to have done their CPU setup
or we might end up with translation and EE on with different
LPCR values between threads
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We do it before we loop on the PACA start flag. This way, we get a
chance to set critical SPRs on all CPUs before Linux tries to start
them up, which avoids problems when changing some bits such as LPCR
bits that need to be identical on all threads of a core or similar
things like that. Ideally, some of that should also be done before
the MMU is enabled, but that's a separate issue which would require
moving some of the SMP startup code earlier, let's not get there
for now, it works with that change alone.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This sets the default data stream prefetch size for operating
systems that don't set their own value in DSCR. We use 4 which
is "medium".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This uses feature sections to arrange that we always use HSPRG1
as the scratch register in the interrupt entry code rather than
SPRG2 when we're running in hypervisor mode on POWER7. This will
ensure that we don't trash the guest's SPRG2 when we are running
KVM guests. To simplify the code, we define GET_SCRATCH0() and
SET_SCRATCH0() macros like the GET_PACA/SET_PACA macros.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rework exception macros a bit to split offset from vector and add
some basic support for HDEC, HDSI, HISI and a few more.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pass the register type to the prolog, also provides alternate "HV"
version of hardware interrupt (0x500) and adjust LPES accordingly
We tag those interrupts by setting bit 0x2 in the trap number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running in Hypervisor mode (arch 2.06 or later), we store the PACA
in HSPRG0 instead of SPRG1. The architecture specifies that SPRGs may be
lost during a "nap" power management operation (though they aren't
currently on POWER7) and this enables use of SPRG1 by KVM guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This bit indicates that we are operating in hypervisor mode on a CPU
compliant to architecture 2.06 or later (currently server only).
We set it on POWER7 and have a boot-time CPU setup function that
clears it if MSR:HV isn't set (booting under a hypervisor).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Even when nothing is specified in the device tree, and despite the
fact that we don't setup links properly yet, we still need a reasonable
value in there or some interrupts won't be setup properly to point to
an existing processor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds more SPR definitions used on newer processors when running
in hypervisor mode. Along with some other P7 specific bits and pieces
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a significant rework of the XICS driver, too significant to
conveniently break it up into a series of smaller patches to be honest.
The driver is moved to a more generic location to allow new platforms
to use it, and is broken up into separate ICP and ICS "backends". For
now we have the native and "hypervisor" ICP backends and one common
RTAS ICS backend.
The driver supports one ICP backend instanciation, and many ICS ones,
in order to accomodate future platforms with multiple possibly different
interrupt "sources" mechanisms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Input: estimate number of events per packet
Input: evdev - indicate buffer overrun with SYN_DROPPED
Input: document event types and codes and their intended use
Input: add KEY_IMAGES specifically for AL Image Browser
Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
Input: h3600_ts - fix error handling at connect
Input: twl4030_keypad - avoid potential NULL-pointer dereference
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: add blk_run_queue_async
block: blk_delay_queue() should use kblockd workqueue
md: fix up raid1/raid10 unplugging.
md: incorporate new plugging into raid5.
md: provide generic support for handling unplug callbacks.
md - remove old plugging code.
md/dm - remove remains of plug_fn callback.
md: use new plugging interface for RAID IO.
block: drop queue lock before calling __blk_run_queue() for kblockd punt
Revert "block: add callback function for unplug notification"
block: Enhance new plugging support to support general callbacks
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/powermac: Build fix with SMP and CPU hotplug
powerpc/perf_event: Skip updating kernel counters if register value shrinks
powerpc: Don't write protect kernel text with CONFIG_DYNAMIC_FTRACE enabled
powerpc: Fix oops if scan_dispatch_log is called too early
powerpc/pseries: Use a kmem cache for DTL buffers
powerpc/kexec: Fix regression causing compile failure on UP
powerpc/85xx: disable Suspend support if SMP enabled
powerpc/e500mc: Remove CPU_FTR_MAYBE_CAN_NAP/CPU_FTR_MAYBE_CAN_DOZE
powerpc/book3e: Fix CPU feature handling on 64-bit e5500
powerpc: Check device status before adding serial device
powerpc/85xx: Don't add disabled PCIe devices
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (24 commits)
Btrfs: fix free space cache leak
Btrfs: avoid taking the chunk_mutex in do_chunk_alloc
Btrfs end_bio_extent_readpage should look for locked bits
Btrfs: don't force chunk allocation in find_free_extent
Btrfs: Check validity before setting an acl
Btrfs: Fix incorrect inode nlink in btrfs_link()
Btrfs: Check if btrfs_next_leaf() returns error in btrfs_real_readdir()
Btrfs: Check if btrfs_next_leaf() returns error in btrfs_listxattr()
Btrfs: make uncache_state unconditional
btrfs: using cached extent_state in set/unlock combinations
Btrfs: avoid taking the trans_mutex in btrfs_end_transaction
Btrfs: fix subvolume mount by name problem when default mount subvolume is set
fix user annotation in ioctl.c
Btrfs: check for duplicate iov_base's when doing dio reads
btrfs: properly handle overlapping areas in memmove_extent_buffer
Btrfs: fix memory leaks in btrfs_new_inode()
Btrfs: check for duplicate iov_base's when doing dio reads
Btrfs: reuse the extent_map we found when calling btrfs_get_extent
Btrfs: do not use async submit for small DIO io's
Btrfs: don't split dio bios if we don't have to
...
Rather than pass in some random truncated offset to the pid-related
functions, check that the offset is in range up-front.
This is just cleanup, the previous commit fixed the real problem.
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
next_pidmap() just quietly accepted whatever 'last' pid that was passed
in, which is not all that safe when one of the users is /proc.
Admittedly the proc code should do some sanity checking on the range
(and that will be the next commit), but that doesn't mean that the
helper functions should just do that pidmap pointer arithmetic without
checking the range of its arguments.
So clamp 'last' to PID_MAX_LIMIT. The fact that we then do "last+1"
doesn't really matter, the for-loop does check against the end of the
pidmap array properly (it's only the actual pointer arithmetic overflow
case we need to worry about, and going one bit beyond isn't going to
overflow).
[ Use PID_MAX_LIMIT rather than pid_max as per Eric Biederman ]
Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Analyzed-by: Robert Święcki <robert@swiecki.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mouse gets "stuck" after restore of PV guest but buttons are in working
condition.
If driver has been configured for ABS coordinates at start it will get
XENKBD_TYPE_POS events and then suddenly after restore it'll start getting
XENKBD_TYPE_MOTION events, that will be dropped later and they won't get
into user-space.
Regression was introduced by hunk 5 and 6 of
5ea5254aa0ad269cfbd2875c973ef25ab5b5e9db
("Input: xen-kbdfront - advertise either absolute or relative
coordinates").
Driver on restore should ask xen for request-abs-pointer again if it is
available. So restore parts that did it before 5ea5254.
Acked-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[v1: Expanded the commit description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Calculate a default based on the number of ABS axes, REL axes,
and MT slots for the device during input device registration.
Signed-off-by: Jeff Brown <jeffbrown@android.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The free space caching code was recently reworked to
cache all the pages it needed instead of using find_get_page everywhere.
One loop was missed though, so it ended up leaking pages. This fixes
it to use our page array instead of find_get_page.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.
Also remove some plug-related code that is no longer needed.
Signed-off-by: NeilBrown <neilb@suse.de>
In raid5 plugging is used for 2 things:
1/ collecting writes that require a bitmap update
2/ collecting writes in the hope that we can create full
stripes - or at least more-full.
We now release these different sets of stripes when plug_cnt
is zero.
Also in make_request, we call mddev_check_plug to hopefully increase
plug_cnt, and wake up the thread at the end if plugging wasn't
achieved for some reason.
Signed-off-by: NeilBrown <neilb@suse.de>
When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.
If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
Signed-off-by: NeilBrown <neilb@suse.de>
