This patch ensures uniformity in event skb sent by interface code
(USB/PCIe/SDIO) which automatically fixes following bugs.
1) For USB interface, same buffer is reused for receiving cmd and
events from firmware. While handling events, we perform
skb_pull(skb, 4) to remove event header. Corresponding skb_push()
call is missing while submitting the buffer.
2) For PCIe interface, event skb is passed with event header.
Recently added uAP events EVENT_UAP_STA_ASSOC, EVENT_UAP_STA_DEAUTH
will not work for PCIe, as they assume event skb points to event body.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After association, STA will go through eapol handshake with WPS
enabled AP. It's observed that WPS handshake fails with some 11n
AP. The reason for the failure is that the eapol packet is sent
via 11n frame aggregation.
The eapol packet should be sent directly without 11n aggregation.
This patch fixes the problem by adding WPS session control while
dequeuing Tx packets for transmission.
Cc: "3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.
Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.
Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Cc: "3.0.y, 3.1.y, 3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_set_disassoc() clears ifmgd->bssid before
building DELBA frames, resulting in frames with invalid
bssid ("00:00:00:00:00:00").
Fix it by clearing ifmgd->bssid only after building
all the needed frames.
After this change, we no longer need to save the
bssid (before clearing it), so remove the local array.
Reported-by: Ido Yariv <ido@wizery.com>
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.
Cc: stable@vger.kernel.org [3.4+]
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging is disabled, the event log functions aren't
functional in the way that the debugfs file expects. This
leads to the debugfs access crashing. Since the event log
functions aren't functional then, remove the debugfs file
when CONFIG_IWLWIFI_DEBUG is not set.
Cc: stable@kernel.org
Reported-by: Lekensteyn <lekensteyn@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c7 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two memory leaks in the SPI initialization code.
Patch based on old maemo patch by:
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always report beacon loss to the stack, not only when in powersave
state. This is because there's possibility that the driver disables
PSM before it handles old BSS_LOSE_EVENT, so beacon loss has to be
reported.
Patch based on old maemo patch by:
Janne Ylalehto <janne.ylalehto@nokia.com>
Juuso Oikarinen <juuso.oikarinen@nokia.com>
Luciano Coelho <luciano.coelho@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cast MSB part of current TSF to u64 to prevent loss of most
significant bits. MSB should also be shifted by 32.
Patch based on old maemo patch by:
Yuri Kululin <ext-yuri.kululin@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add_virtual_intf() needs to return an ERR_PTR(), instead of NULL,
on errors, otherwise cfg80211 will crash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"qual" used to be declared on the stack, but then in 998a5a7d6a ("airo:
reduce stack memory footprint") we made it dynamically allocated.
Unfortunately the memcpy() here was missed and it's still copying stack
memory instead of the data that we want. In other words, "&qual" should
be "qual".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running heavy traffic we stop the tx queue if the pending
packet count reaches certain threshold. Later, the tx queue should
be woken up as soon as the packet count falls below the threshold.
Current code wakes TX queue up on STA interface only. Removing the
check for STA interface will allow both STA and AP interfaces to
resume transmit when tx_pending count becomes low.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin_unlock_bh(&txq->lock) already disables softirqs so we don't want
to do it here. Fixes smatch warnings:
drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:'
drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:'
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.
This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
HCI_Disconnect should only be sent after connection is established.
If connection is not yet established and HCI_Disconnect is called
then disconnection complete will be received with a handle which
does not exist and hence this event will be ignored.
But as mgmt.c will not receive this event, its variable for pending
command is not cleared.This will result in future Disconnect commands
for that BD Address to be blocked with error busy.
Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stop connection monitor poll during disassociation.
This clears the polling flags and if a scan was
deferred it will be run.
Without this fix, if a scan was deferred due to
connection monitoring while disassociation happens,
this scan blocks further scan requests until interface
down/up which causes problems connecting to another AP.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we might call the driver callback before
the interface was uploaded.
Solves the following warning:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x0
Modules linked in: wlcore_sdio wl12xx wl18xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[<c001b964>] (unwind_backtrace+0x0/0x12c) from [<c0495550>] (dump_stack+0x20/0x24)
[<c0495550>] (dump_stack+0x20/0x24) from [<c003ee28>] (warn_slowpath_common+0x5c/0x74)
[<c003ee28>] (warn_slowpath_common+0x5c/0x74) from [<c003eefc>] (warn_slowpath_fmt+0x40/0x48)
[<c003eefc>] (warn_slowpath_fmt+0x40/0x48) from [<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211])
[<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]) from [<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211])
[<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211]) from [<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8)
[<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8) from [<c03e9164>] (netlink_rcv_skb+0x5c/0xc0)
[<c03e9164>] (netlink_rcv_skb+0x5c/0xc0) from [<c03e9ce0>] (genl_rcv+0x28/0x34)
[<c03e9ce0>] (genl_rcv+0x28/0x34) from [<c03e8e74>] (netlink_unicast+0x158/0x234)
[<c03e8e74>] (netlink_unicast+0x158/0x234) from [<c03e93e0>] (netlink_sendmsg+0x218/0x298)
[<c03e93e0>] (netlink_sendmsg+0x218/0x298) from [<c03b4e5c>] (sock_sendmsg+0xa4/0xc0)
[<c03b4e5c>] (sock_sendmsg+0xa4/0xc0) from [<c03b5af4>] (__sys_sendmsg+0x1d8/0x254)
[<c03b5af4>] (__sys_sendmsg+0x1d8/0x254) from [<c03b5ca8>] (sys_sendmsg+0x4c/0x70)
[<c03b5ca8>] (sys_sendmsg+0x4c/0x70) from [<c0013980>] (ret_fast_syscall+0x0/0x3c)
Note that calling the driver can also result
in undefined behaviour since it doesn't have
to deal with calls while down.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[removed timestamps, added note - Johannes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Test procedure:
1. Start AP with security setting (e.g. WPA2)
2. Stop AP
3. Start AP with open security
Here it's observed that privacy is enabled in beacons and
probe responses.
This patch fixes it by checking the privacy parameter from
cfg80211_ap_settings. If privacy is not set in cfg80211_ap_settings,
set open authentication and no encryption in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a few kernel-doc descriptions that were missed
during mesh development.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If remote device sends bogus RFC option with invalid length,
undefined options values are used. Fix this by using defaults when
remote misbehaves.
This also fixes the following warning reported by gcc 4.7.0:
net/bluetooth/l2cap_core.c: In function 'l2cap_config_rsp':
net/bluetooth/l2cap_core.c:3302:13: warning: 'rfc.max_pdu_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.max_pdu_size' was declared here
net/bluetooth/l2cap_core.c:3298:25: warning: 'rfc.monitor_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.monitor_timeout' was declared here
net/bluetooth/l2cap_core.c:3297:25: warning: 'rfc.retrans_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.retrans_timeout' was declared here
net/bluetooth/l2cap_core.c:3295:2: warning: 'rfc.mode' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.mode' was declared here
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
rndis_check_bssid_list() originally tried to check if bssid->mac and
match_bssid are equal using compare_ether_addr() when it should use
!compare_ether_addr(). This check was added by commit
b5257c952d as part of workaround for
hardware issue.
Commit 2e42e4747e that replaced
compare_ether_addr with ether_addr_equal relieved that this compare
to be inverse of what it should be.
Compare was added as response to hardware bug, where bssid-list does
not contain BSSID and other information of currently connected AP
(spec insists that device must provide this information in the list
when connected). Lack bssid-data on current connection then causes
WARN_ON somewhere in cfg80211. Workaround was to check if bssid-list
returns current bssid and if it does not, manually construct bssid
information in other ways. And this workaround worked, with inverse
check. Which must mean that when hardware is experiencing the problem,
it's actually returning empty bssid-list and this check didn't make
any difference for workaround.
However inverse check causes workaround be activated when bssid-list
returns only entry, currently connected BSSID. That does not cause
problems in itself, just slightly more inaccurate information in
scan-list.
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.
this patch is dependent on 'cfg80211: fix interface combinations'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch is dependent on the patch "cfg80211: fix interface
combinations"
In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC. we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.
The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.
ath: phy0: Cannot create ADHOC interface when other
interfaces already exist.
WARNING: at net/mac80211/driver-ops.h:12
ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
Hardware name: 2842RK1
wlan2: Failed check-sdata-in-driver check, flags: 0x0
Call Trace:
[<c01361b2>] warn_slowpath_common+0x72/0xa0
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<c0136283>] warn_slowpath_fmt+0x33/0x40
[<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
[<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
[<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
[<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't validate interface combinations on a stopped
interface. Otherwise we might end up being able to
create a new interface with a certain type, but
won't be able to change an existing interface
into that type.
This also skips some other functions when
interface is stopped and changing interface type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a few kernel-doc descriptions that were missed
during development.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With LE/SMP the completion of a security level elavation from medium to
high is indicated by a HCI Encryption Key Refresh Complete event. The
necessary behavior upon receiving this event is a mix of what's done for
auth_complete and encryption_change, which is also where most of the
event handling code has been copied from.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
commit 24398e39c8
Author: Johannes Berg <johannes.berg@intel.com>
Date: Wed Mar 28 10:58:36 2012 +0200
mac80211: set HT channel before association
removed IEEE80211_CONF_CHANGE_CHANNEL argument from ieee80211_hw_config,
which is required by iwl4965 driver, otherwise that driver does not
configure channel properly and is not able to associate.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
llcp_sock_getname() might get called before the LLCP socket was created.
This condition isn't checked, and llcp_sock_getname will simply deref a
NULL ptr in that case.
This exists starting with d646960 ("NFC: Initial LLCP support").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Cc: stable@vger.kernel.org [2.6.27+]
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch fixes kernel Oops on "rmmod b43" if firmware was not loaded:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff8104e988>] drain_workqueue+0x25/0x142
PGD 153ac6067 PUD 153b82067 PMD 0
Oops: 0000 [#1] SMP
Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch
iwlwifi: use correct released ucode version
did not correctly report supported firmware
for the 6035 device. This patch fixes it. The
minimum supported firmware version for 6035
is v6.
Also correct the minimum supported firmware
version for the 6000g2 series of devices.
Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add my new trees to the MAINTAINERS file
for the components that I maintain in the
new trees.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station fail average is not updated correctly since the
IEEE80211_STAT_ACK flag is not set when using wmediumd with
mac80211_hwsim. Set this flag when wmediumd indicates that the frame
was successfully transmitted (eventually).
Signed-off-by: Qasim Javed <qasimj@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix:
BUG: sleeping function called from invalid context at kernel/workqueue.c:2547
in_atomic(): 1, irqs_disabled(): 0, pid: 629, name: wpa_supplicant
2 locks held by wpa_supplicant/629:
#0: (rtnl_mutex){+.+.+.}, at: [<c08b2b84>] rtnl_lock+0x14/0x20
#1: (&trigger->leddev_list_lock){.+.?..}, at: [<c0867f41>] led_trigger_event+0x21/0x80
Pid: 629, comm: wpa_supplicant Not tainted 3.3.0-0.rc3.git5.1.fc17.i686
Call Trace:
[<c046a9f6>] __might_sleep+0x126/0x1d0
[<c0457d6c>] wait_on_work+0x2c/0x1d0
[<c045a09a>] __cancel_work_timer+0x6a/0x120
[<c045a160>] cancel_delayed_work_sync+0x10/0x20
[<f7dd3c22>] rtl8187_led_brightness_set+0x82/0xf0 [rtl8187]
[<c0867f7c>] led_trigger_event+0x5c/0x80
[<f7ff5e6d>] ieee80211_led_radio+0x1d/0x40 [mac80211]
[<f7ff3583>] ieee80211_stop_device+0x13/0x230 [mac80211]
Removing _sync is ok, because if led_on work is currently running
it will be finished before led_off work start to perform, since
they are always queued on the same mac80211 local->workqueue.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=795176
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have an unauthenticated key it is not sufficient to acheive high
security. Therefore, when deciding whether to encrypt the link or
request pairing, it is essential to in addition to checking the
existence of a key to also check whether it is authenticated or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The l2cap_conn_del function tries to cancel_sync the security timer, but
when it's called from the timeout function itself a deadlock occurs.
Subsequently the "hcon->l2cap_data = NULL" that's supposed to protect
multiple calls to l2cap_conn_del never gets cleared and when the
connection finally drops we double free's etc which will crash the
kernel.
This patch fixes the issue by using the HCI_CONN_LE_SMP_PEND for
protecting against this. The same flag is also used for the same purpose
in other places in the SMP code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
