This processor only have one FEC and its MDIO pins are
located at a different offset than the code used for
the current CONFIG_M527x.
Tesed on M5271EVB eval platform.
Without this patch the FEC driver will report no PHY attached
if the bootloader does not pre-initialize the PAR_FECI2C GPIO register.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (41 commits)
m68knommu: improve compile arch switch settings
m68knommu: fix 5407 ColdFire UART vector setup
m68knommu: fix 5307 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART setup
m68knommu: fix end of uart table marker
m68knommu: switch to using generic_handle_irq()
m68k: merge the mmu and non-mmu versions of tlbflush.h
m68knommu: introduce basic clk infrastructure
m68k: merge the mmu and non-mmu versions of module.h
m68knommu: add missing interrupt line definition for UART 2
m68k: merge the mmu and non-mmu versions of mmu_context.h
m68k: merge the mmu and non-mmu versions of current.h
m68k: merge the mmu and non-mmu versions of div64.h
m68k: merge the mmu and non-mmu versions of bugs.h
m68k: merge the mmu and non-mmu versions of bug.h
m68k: use the mmu version of cache.h for m68knommu as well
m68k: use the mmu version of bootinfo.h for m68knommu as well
m68k: merge the mmu and non-mmu versions of fb.h
m68k: merge the mmu and non-mmu versions of segment.h
...
There is a couple of problems with the UART vector setup for the 5307
ColdFire UART. The ICR register access should be 8bit, not 32bit. The
address of the UIVR register is wrong, it needs to be offset into the
MBAR register region. Fix these.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
There is a couple of problems with the UART vector setup for the 5307
ColdFire UART. The ICR register access should be 8bit, not 32bit. The
address of the UIVR register is wrong, it needs to be offset into the
MBAR register region. Fix these.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The address of the IVUR register is not correct, it should be offset
into the MBAR region. Without this the vector is not set to the correct
number.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ICR registers of the 5249 ColdFire processor are 8bits, not 32bits.
Fix the read/write of these register to be the correct size.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The UART platform data structure is missing an empty struct at the
end (as the end of structure marker).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Create basic support for clk API. Recent changes to the FEC driver
(used by many ColdFire family parts) need this. Initially only
supports getting the master clock frequency.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
There isn't any mcfqspi.h in the tree, and without it everything inside the
#ifdef CONFIG_SPI is uncompilable.
Signed-off-by: Steven King <sfking@fdwdc.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68knommu: add FEC platform support to ColdFire CPU's setup code
Move the per-CPU FEC driver setup code into the actual platform
setup code for each ColdFire CPU varient.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5329 ColdFire peripheral IO register addresses are not relative to
the MBAR register. So fix the serial platform setup array and IRQ acking
to use just the direct addresses.
Signed-off-by: Matt Waddel <Matt.Waddel@freescale.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer said about this board:
Only ever a handful where made, and that was in 1999.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Part of the code that did not make sense to me got removed by Greg.
This is part two:
The first compare is to check whether the interrupts are disabled or not.
Depending on the result we exectute the RESTORE_ALL macro is not only
restoring the stack but also returning to caller.
The test for pending softirq has been removed because it is allready done
in irq_exit().
Since system_call() is allso using the SAVE_ALL macro and returning via
ret_from_exception label I see no reason why we could not do this here
as well. This is also handy because if we return from the timer interrupt
and we need to resched than we check for this :)
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Switch the ColdFire head start up code to be in the .text.head segment.
And make sure that segment is at the start of the final linked text
segment. Fixes the linker warnings about section use mis-matches:
WARNING: vmlinux.o(.text+0xa8): Section mismatch in reference from the variable _clear_bss to the function .init.text:start_kernel()
The function _clear_bss() references
the function __init start_kernel().
This is often because _clear_bss lacks a __init
annotation or the annotation of start_kernel is wrong.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The PIT code has been changed in order to suppport GENERIC_CLOCKEVENTS.
The priority of the PIT clocksource has been decreased in favor of the
DMA timer.
pit_cycles_per_jiffy become a constant (PIT_CYCLES_PER_JIFFY) because it
is known at compile time and does not change afterwards.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
with this printk() and other sched_clock() user use the more precise
timestamps. The highly optimized math is from arch/x86/kernel/tsc_32.c.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This one could be used as a hrtimer.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The coldfire timer must be initialised to n - 1 if we want it to count n
cycles between each tick interrupt. This was already fixed, but has been
lost with the conversion to GENERIC_TIMER.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interrupts must be disabled before considering the need resched
bit of the task struct and they have to be disabled before calling
schedule()
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused CONFIG_DISKtel support.
Missing config definition pointed out by
Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds linux-2.6.x kernel support for the Intec Automation
ColdFire 5282-based boards, the WildFire and WildFireMod
Signed-Off-By: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused board type CONFIG_MTD_KeyTechnology.
Pointed out by Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the subject says this patch adds the support for kernel preemption
on m68knommu Coldfire. I thing the same changes could be applied to
68360 & 68328 but since I don't have the HW for testing, I don't touch it.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I was looking at timers in the Coldfire system and I noticed that the
CONFIG_HIGHPROFILE option seems to be a little out of date.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify the extra asm flags for debugger capabilities, use asflags instead for
EXTRA_AFLAGS. Suggestion from Sam Ravnborg.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove bogus conditional jump in return from interrupt path. Reorder the code
path now that is not there.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove all the dead timer interrupt checking functions for the ColdFire
CPU "timers" hardware that are not used after switching to GENERIC_TIME.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switching to GENERIC_TIME means we no longer need the empty timer offset
function for the 68360 CPU.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the 68328 CPU timer code to using GENERIC_TIME.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the ColdFire DMA address table into its own file, and out
of each of the different CPU config files. No need to have a copy
of it in each of the config setup files.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify Makefiles to support separate coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move common ColdFire CPU vectors.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move common ColdFire CPU timers.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move common ColdFire CPU pit.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move common ColdFire CPU head.S to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move common ColdFire CPU entry.S to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 5407 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 532x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 527x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 5307 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 528x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 5249 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
