iwl_legacy prefix result in long function names, what cause that we
have frequent line split and not readable code. Also iwl_foo symbols
are duplicated in iwlwifi driver, what is annoying when editing
kernel tree with cscope.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
The warning is spurious -- if !sta we always exit without using the
unassigned qos variable, and if we do find the sta we assign it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/libertas/cfg.o
drivers/net/wireless/libertas/cfg.c: In function ‘lbs_ret_scan’:
drivers/net/wireless/libertas/cfg.c:636:24: warning: ignoring return value of ‘cfg80211_inform_bss’, declared with attribute warn_unused_result
drivers/net/wireless/libertas/cfg.c: In function ‘lbs_join_post’:
drivers/net/wireless/libertas/cfg.c:1766:21: warning: ignoring return value of ‘cfg80211_inform_bss’, declared with attribute warn_unused_result
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/brcm80211/brcmsmac/srom.o
drivers/net/wireless/brcm80211/brcmsmac/srom.c: In function ‘_initvars_srom_pci’:
drivers/net/wireless/brcm80211/brcmsmac/srom.c:641:6: warning: ‘val’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Referenced struct returned by cfg80211_inform_bss must be released with
cfg80211_put_bss to avoid memory leak.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
all the devices supported or will be supported by brcmfmac
do not have a PCMCIA bus core. So remove the corresponding code.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In several places in dhd_sdio.c a skb packet queue was being emptied
and the packets freed. This warrants to have a function in place to
do this.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmu_pkt_buf_free_skb() was following the next pointer
to free all linked packets. However, it is only called with unlinked
packets so this can be removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions brcmu_pkttotlen() is only used in brcmfmac driver
so it has been moved there. It also does not use the sk_buff
next pointer anymore but walks a skb queue to determine the total
length.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combined mac configuration for promiscious mode and monitor mode, and
removed unused monitor mode flag in pub structure.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of dealing with sk_buff prev pointers the queue functions
now make use of the sk_buff_head functions provided by the kernel.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmu_pkttotlen calculates the total length of a sk_buff
chain following the next pointer. In brcmsmac this is not needed as
in each place where it was used the provided sk_buff had a NULL pointer
as next field value.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sdio_chip.c is dedicated to sdio bus chip. No need to retrieve id
for bus core
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the series of adding new backplane support
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the series of adding new backplane support
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the series adding new backplane support
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New type of backplane interconnect support is needed
for bcm4330
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macro definition D11_PHY_HDR_LEN was defined in d11.h and pub.h.
It has been removed from pub.h.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac had own definitions for the access categories. The mac80211
header provides these as well as they are used in the conf_tx callback.
As the definitions did not match the driver configured the tx parameters
to the wrong queue.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a couple of code segments left that were placed under
a macro definition that was not applicable or not used in the
brcmsmac driver. These pieces of code have been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes issue when using OTP memory. It was introduced by
following commit:
commit 028f78d43d
Author: Arend van Spriel <arend@broadcom.com>
Date: Fri Oct 21 16:16:35 2011 +0200
brcm80211: smac: change buffer endianess convert function interface
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nvm_device_type is eeprom related and does not need to be part
of the iwl_priv structure. Move it and eliminate access to the iwl_priv
structure.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the eeprom routines less dependent on the iwl_priv structure.
Don't use the priv when bus structure is sufficient.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi tries to avoid using antenna B in BT combo devices when BT
is active. A bug in the rate-scaling algorithm was causing the combo
device to never attempt MIMO rates. Fix the algorithm to
opportunistically try MIMO rates when BT traffic is low.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users complain that the traffic gets stalled sometimes. This will
allow easier debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bit was used only once. Use IWL_DL_INFO instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the P2P context always having the associated
bit set when we got to this code, we were splitting
up the remain-on-channel durations unconditionally.
This isn't needed -- if the P2P context is in P2P
device type mode it doesn't impose restrictions on
timing to skip it in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device expects TU but we get ms, so convert.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Warning introduced by c847474b7dfdda304d0d8ffcc5a9db546b1cb3e9
iwlwifi: check status before send command
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the status before sending host command, if any of the condition
match, cancel the host command before queue
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"echo" host command has no data, set the length to 0
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core suspend function is part of agn, iwl_mac80211 should only
handle mac80211 I/F operations.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station related mac80211 callback functions should belong to _mac80211
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn_mac_hw_scan should belong to _mac80211 callback.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move more mac80211 related functions to _mac80211 file
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In P2P device mode, the device needs to have valid
QoS parameters. We currently have those because we
program parameters from any virtual interface into
all contexts, but not only do we want to get rid of
this -- it is also unpredictable since on the BSS
context we might have any parameters, and there it
might even be programmed for HT.
Explicitly program default QoS parameters into the
PAN context for P2P (the defaults are 11g but with
QoS disabled) to make device behaviour predictable.
This also helps when in a follow-up patch we will
use TX QoS parameters from mac80211 only for the
context they were meant for -- without this first
that would completely break P2P device discovery.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad added the ability to configure AC parameters
per virtual interface; make use of this in iwlwifi
and set the parameters in the right context. Since
storage and uploading to the device is already per
context, this is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are many mac80211 callback functions in the driver, as current
implementation, those functions are scatter everywhere which is very difficult
to find and maintain, move all the mac80211 callback functions into single
file. There should be no functional changes
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Relocate the ucode files and update relevant code.
More code refactoring.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the knowledge of the ucode image to lower level routines. Also do
not pass the iwl_priv structure lower than it needs to be.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The upper layers of the driver do not need to know where the ucode is
stored. It already passes in an enum of which ucode to load. Let the
lower layer routines select the ucode to load.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ucode_write_complete is used for ucode loading. Move it as part of
restructuring work out of the priv structure.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BG only SKUs are no longer supported by 2000 and 1x5 series. Remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette reports a crash in iwl_reprogram_ap_sta(). The
debugging shows:
b1 16 mov $0x16,%cl
*f3 a5 rep movsl %ds <-- trapping instruction:(%rsi),%es:(%rdi)
which is a memcpy of 22 (0x16) words (movsl). this points
to "priv->stations[sta_id].lq" being NULL since that is
the memcpy() of that size here.
The only way I see for this to happen is if we try to
do some RXON reprogramming while connecting to an AP,
after tx_sync() but before full setup, but that seems
like something that might very well happen.
Fix this by checking if the LQ is present and only then
reprogramming it.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check and report WARN only when its invalid
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add two more SKUs for 6x05 series of device.
First SKU has low 5GHz channels actives, the other SKU has high 5GHz channels actives.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
