Pre-allocate a skb at init time to be used for control messages to the HW
if skb allocation fails.
Tolerate failures to send messages initializing some memories at the cost of
parity error detection for these memories.
Retry sending connection id release messages if both alloc_skb(GFP_ATOMIC)
and alloc_skb(GFP_KERNEL) fail.
Do not bring the interface up if messages binding queue set to port fail to
be sent.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic MDIO generic values.
Based on Ben Hutchings'review comments.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the AEL2020 phy.
Add PCI IDs of the boards using this phy.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not call t3_link_fault() under spinlock, as it calls msleep().
Besides, only the access to pi->link_fault needs to be serialized.
Also initialize local variables before checking the link status,
link state fields might otherwise end up containing garbage.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5e68b772e6
cxgb3: map entire Rx page, feed map+offset to Rx ring.
introduced a regression on platforms defining DECLARE_PCI_UNMAP_ADDR()
and related macros as no-ops.
Rx descriptors are fed with the a page buffer bus address + page chunk offset.
The page buffer bus address is set and retrieved through
pci_unamp_addr_set(), pci_unmap_addr().
These functions being meaningless on x86 (if CONFIG_DMA_API_DEBUG is not set).
The HW ends up with a bogus bus address.
This patch saves the page buffer bus address for all plaftorms.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio's dev field needs to be set before mdio ops occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial: fixing gcc 4.4 compiler warning:
drivers/net/cxgb3/t3_hw.c: In function ‘t3_prep_adapter’:
drivers/net/cxgb3/t3_hw.c:3782: warning: suggest parentheses around operand of ‘!’ or change ‘|’ to ‘||’ or ‘!’ to ‘~’
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH attempts to recover up 6 times.
The last attempt leaves all the ports and adapter down.hen
The driver is then unloaded, bringing the adapter down again
unconditionally. The unload will hang.
Check if the adapter is already down before trying to bring it down again.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fatal error task can be scheduled while processing an offload packet
in NAPI context when the connection handle is bogus. this can race
with the ports being brought down and the cxgb3 workqueue being flushed.
Stop napi processing before flushing the work queue.
The ULP drivers (iSCSI, iWARP) might also schedule a task on keventd_wk
while releasing a connection handle (cxgb3_offload.c::cxgb3_queue_tid_release()).
The driver however does not flush any work on keventd_wq while being unloaded.
This patch also fixes this.
Also call cancel_delayed_work_sync in place of the the deprecated
cancel_rearming_delayed_workqueue.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing periodic task to handle link faults.
The link fault interrupt handler is also called in work queue context,
which is wrong and might cause potential deadlocks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that copying a 16-byte area at ~800k times a second
can be really expensive :) This patch redesigns the frags GRO
interface to avoid copying that area twice.
The two disciples of the frags interface have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DMA mapping can be expensive in the presence of iommus.
Reduce the Rx iommu activity by mapping an entire page, and provide the H/W
the mapped address + offset of the current page chunk.
Reserve bits at the end of the page to track mapping references, so the page
can be unmapped.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t to declare mmio start and len variables.
Print PEX error register after EEH resumed.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable timestamps, update delayed ack threshold for iSCSI/iWARP traffic
Remove the len flag in Tx requests. It might corrupt offload trace packets.
Update SGE context setup to avoid potential H/W misprogrammation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start queue set reclaim timers after the queue sets have been
allocated successfully.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently ignores the local or remote link faults
raised at the mac layer. This patch fixes it.
Our mac however only advertizes link events, so wait for the
phy to stabilize the link, then enable mac link events interrupts.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the heurstics workaround unlocking a hung mac:
- reduce Tx mac toggling by enabling Tx drain before resetting the mac
- Take Tx (lack of) activity in account only
- Update the monitoring counter range to 64 bits
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under RX pressure, The HW might generate a high load of interrupts
to signal mac fifo or free lists overflow.
Disable the interrupts, and poll the relevant status bits
to maintain stats.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate TX and RX reclaim handlers
Don't disable interrupts in RX reclaim handler.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Elmininate a cache miss when accessing the CPL header within
the first aggregated buffer.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update skb truesize correctly for the 2nd buffer from a Jumbo frame
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release page chunk reference in case we fail to map it.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ring free lists door bell less frequently,
specifically every quarter of the active FL
size.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adapters with a PCI id equal to 0x35.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warning:
drivers/net/cxgb3/ael1002.c:1010:60: warning: incorrect type in argument 4 (different signedness)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move variable declaration as close to usage as possible.
Fix this sparse warning:
drivers/net/cxgb3/cxgb3_main.c:1586:21: warning: symbol 'cap' shadows an earlier one
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LRO switch is always set to 1 in the rx processing loop.
It breaks the accelerated iSCSI receive traffic.
Fix its computation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set up a notification mechanism to inform upper layer modules
(iWARP, iSCSI) of a chip reset due to an EEH event or a fatal error.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes cxgb3 invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
I've kept the ioctl controls for per-queue LRO switches. However,
we should not encourage anyone to use these.
Because of that, I've also kept the skb construction code in
cxgb3. Hopefully we can phase out those per-queue switches
and then kill this too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently drops to line interrupt mode
if it did not get all the msi-x vectors it requested.
Allow msi-x settings when a minimal amount of vectors
is provided.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lro manager's frag_align_pad setting was missing,
leading to misaligned access to the skb passed up
to the stack.
Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a system with a Chelsio adapter (driven by cxgb3) whose ports are
part of a Linux bridge. Recently I updated the kernel and discovered
that things stopped working because cxgb3 was doing LRO on packets that
were passed into the bridge code for forwarding. (Incidentally, this
problem manifested itself in a strange way that made debugging a bit
interesting -- for some reason, the skb_warn_if_lro() check in bridge
didn't trigger and these LROed packets were forwarded out a forcedeth
interface, and caused the forcedeth transmit path to get stuck)
This is because cxgb3 has no way of keeping state for the LRO flag until
the interface is brought up, so if the bridging code disables LRO while
the interface is down, then cxgb3_up() will just reenable LRO, and on my
Debian system at least, the init scripts add interfaces to a bridge
before bringing the interfaces up.
Fix this by keeping track of each interface's LRO state in cxgb3 so that
when bridge disables LRO, it stays disabled in cxgb3_up() when the
interface is brought up. I did this by changing the rx_csum_offload
flag into a pair of bit flags; the effect of this on the rx_eth() fast
path is miniscule enough that it should be fine (eg on x86, a cmpb
instruction becomes a testb instruction).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>