Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The irq_set_wake() function of the gpio irq_chip calls
enable/disable_irq_wake() on the demultiplex interrupt. That leads to
a lockdep warning "INFO: possible recursive locking detected" because
irq_set_type() is called under irq_desc->lock and the *_irq_wake()
calls take irq_desc->lock of the demux interrupt.
Tell lockdep that the gpio irqs are in a different lock class.
Documentation/SubmitChecklist:
15: All codepaths have been exercised with all lockdep features enabled.
That's a non-optional requirement, AFAICT.
Reported-and-tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LAKML-Reference: alpine.LFD.2.00.1104041416290.19945@localhost6.localdomain6
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
LAKML-Reference: 1289913217-8672-1-git-send-email-dave.martin@linaro.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Implement code for MX51 that allows the SoC to enter WFI when
arch_idle is called.
This patch is also necessary for correctly suspending the system.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For MX50, the HW_ADADIG_DIGPROG register in the ANATOP module will
have the correct silicon revision:
Major Minor Description
0x50 0x0 TO1.0
0x50 0x1 TO1.1
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add sched_clock using cyc_to_sched_clock and update_sched_clock
with HAVE_SCHED_CLOCK
tested on iMX27 and iMX35
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this is needed to use get_cycles with sched_clock. Accessing timer
without enabled clk will result in crash
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Having the silicon revision to appear on the boot log is a useful information.
MX31 and MX35 already show the silicon revision on boot.
Add support for displaying such information for MX51 as well.
Tested on a MX51EVK, where it shows:
CPU identified as i.MX51, silicon rev 3.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: dw_mmc: support mmc power control with regulator
mmc: dw_mmc: fix suspend/resume operation
mmc: dw_mmc: add quirks for unreliable card detect, and capabilities
mmc: tmio: fix address in kunmap_atomic() calls
mmc: core: reset card voltage after power off
mmc: core: export function mmc_do_release_host()
mmc: sdio: remember new card RCA when redetecting card
mmc: dw_mmc: Remove set-but-unused variable.
mmc: sdhci-esdhc-imx: add card detect on custom GPIO for mx25/35
mmc: sdhci-esdhc: broken card detection is not a default quirk
mmc: sdhci-esdhc-imx: add write protect on custom GPIO on mx25/35
mmc: msm_sdcc: remove needless cache flush after dma_unmap_sg()
mmc: sh_mmcif: support aggressive clock gating
mmc: check if mmc cards < 2GB do sector addressing
mmc: core: comment on why sdio_reset is done at init time
mmc: dw_mmc: support DDR mode
mmc: via-sdmmc: Remove set-but-unused variable.
mmc: cb710: Return err value in cb710_wait_while_busy()
mmc: sdhci-pci: Remove set-but-unused variable.
mmc: mxs-mmc: add mmc host driver for i.MX23/28
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some cards have the CRC errors in read on mx51 BBG board.
Configure the eSDHC pad configurations to level up the
compatibility to fix this issue.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes:
arch/arm/kernel/built-in.o: In function `__irq_svc':
io.c:(.text+0x2e0): undefined reference to `avic_base'
arch/arm/kernel/built-in.o: In function `__irq_usr':
io.c:(.text+0x4c8): undefined reference to `avic_base'
arch/arm/mach-mxc91231/built-in.o: In function `mxc91231_init_irq':
magx-zn5.c:(.init.text+0x18): undefined reference to `mxc_init_irq'
and was broken by
c7259df (ARM i.MX irq: Compile avic irq code only on SoCs that need it)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following warning in a mx3_defconfig build:
arch/arm/mach-mx3/mach-bug.c: In function 'bug_board_init':
arch/arm/mach-mx3/mach-bug.c:47: warning: passing argument 1 of 'mxc_iomux_setup_multiple_pins' discards qualifiers from pointer target type
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the "i.MX35 (MCIMX35) Multimedia Applications Processor
Reference Manual" the correct address for the pad control register
IOMUXC_SW_PAD_CTL_PAD_ATA_DATA3 is 0x06ec, not 0x6e8.
Signed-off-by: Ryan Lortie <desrt@desrt.ca>
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Note that the hardware schematics and documentations can be obtained
here: http://www.bugcommunity.com/wiki/index.php/BUGbase
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most fix is for uart txd/cts. They don't need to select input.
And fix some other pads with wrong select input.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes 2 small regressions of recent iomux changes:
- current MX51_PAD_UART2_TXD__UART2_TXD declaration overwrites
IOMUXC_UART2_IPP_UART_RXD_MUX_SELECT_INPUT register (0x09ec) and prevent
UART2 Rx from working properly.
(Tested on my custom i.MX51 board where UART2 is used as console)
- current MX51_PAD_USBH1_DATA2__UART2_TXD declaration also has the same problem.
(Not tested)
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we have a mxc_initialize_usb_hw which is called on every
i.MX SoC. This function dispatches the different SoC types, which
is quite ugly. This patch moves the SoC specific USB initialization
to their correspondive mach directories.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the memory
mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This iomux file contains all the available pins that are iomux
capable.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is adding support for pwm1 and pwm2 devices found
on mx51.
[ this patch has been tested with pwm-backlight driver ]
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for dynamical allocation of imx-keypad on mx5 platform.
After moving to dynamically registration of the keypad, the keypad clock
name needs to change accordingly.
The reason is that the original mx5 keypad platform_device id was 0,
now we use id=-1 as per arch/arm/plat-mxc/devices/platform-imx-keypad.c.
Tested keypad successfully on a MX51_3DS board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
1. changes some register address to fit macro definition
2. add platform data and clock for sdhc
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
1. Adjust FEC base address name to fit macro definition
2. Add platform data and reset function for FEC
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is fixing some issues :
- MXC_OTG_UCTRL_OPM_BIT is for USBCTRL register and not PHYCTRL register.
- the MXC_EHCI_WAKEUP_ENABLED check was only clearing the bits so never allows
to set them.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add basic function and uart device support.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mx5 SoCs have different GPIO port count.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
This iomux file has been constructed from the Freescale pinmux tool.
It contains all pins from the tool, but the datasheet lists some
configurations not present in the tool, these are not yet added.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch actually replaces the 'struct pad_desc' with a u64 cookie
to facilitate adding platform specific pad_ctrl settings to an
existing pad definition.
So, instead of:
iomux_v3_cfg_t power_key = MX51_PAD_EIM_A27__GPIO_2_21;
power_key.pad_ctrl = MX51_GPIO_PAD_CTRL_2;
mxc_iomux_v3_setup_pad(&power_key);
one can write:
mxc_iomux_v3_setup_pad((MX51_PAD_EIM_A27__GPIO_2_21 & ~MUX_PAD_CTRL_MASK) | MX51_GPIO_PAD_CTRL_2);
Patch applies to branch 'imx-for-2.6.38' of git://git.pengutronix.de/git/imx/linux-2.6
Signed-Off-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When building as module:
ERROR: "cpufreq_gov_performance" [arch/arm/plat-mxc/cpufreq.ko] undefined!
WARNING: modpost: Found 1 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
It's due to the driver using CPUFREQ_DEFAULT_GOVERNOR, even it should not
(see commit 8122c6cea0 in Linus tree), so
remove it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for FIQ on mx51 TZIC
TZIC changes tested with FIQ audio on an mx51 board
AVIC changes build with mx3_defconfig, not tested
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use clk_get to acquire the watchdog clock and also avoid hardcoding the clock name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MX51 has two watchdog modules.
Add support for both of them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, to define a GPIO number, we're using something like :
#define EFIKAMX_PCBID0 (2*32 + 16)
to define GPIO 3 16.
This is not really readable and it's error prone imho (note the 3 vs 2).
So, I'm introducing a new macro to define this in a better way. Now, the
code sample become :
#define EFIKAMX_PCBID0 IMX_GPIO_NR(3, 16)
v2:
- move to gpio.h
- add parens & spaces
- switch to IMX_GPIO_NR instead of MX51_GPIO_NR
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In commit 2c20b9f (ARM: mx25: dynamically allocate mxc-ehci devices) I
changed the offset to the value specified in the reference manual
intending to test this change on hardware. This slipped through and now
prooved to be wrong. So fix it and add a comment about the
documentation being wrong.
Reported-by: Jaume Ribot <jaume@fqingenieria.es>
Cc: Michael Trimarchi <trimarchi@gandalf.sssup.it>
Cc: Shawn Guo <shawn.gsc@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commits 2eb42d5c28 and
9e1dde3387 renamed some defines
but didn't fix all the places where these defines are used
leading to a compile failure for USB on i.MX31, 35 and 27.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The SDMA firmware consists of a ROM part and a RAM part.
The ROM part is always present in the SDMA engine and
is sufficient for many cases.
This patch allows to pass in platform data containing
the script addresses in ROM, so loading a firmware is
optional now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Instead of reading the silicon version from ROM, we should
read the SREV register from the IIM.
Freescale has dropped all support for MX51 REV1.0, only MX51
REV 2.0 and 3.0 are valid.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
