Make the output for PCM parameters more verbose, showing
each rate, bits and format.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Don't include 9.6kHz in the list of supported sample rates.
Since this rate isn't indicated in AC_PAR_PCM parameter,
the driver might guess wrongly as if it's available.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add a proper model entry (laptop-eapd) for ASUS V1j laptop with
AD1986A codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch removes some obviously dead code spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The case where silence_size < boundary was broken because different
parts of the snd_pcm_playback_silence() function disagreed about whether
silence_start should point to the start or to the end of the buffer part
to be silenced.
This patch changes the code to always use to the start, which also
simplifies several calculations.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
precise_ptr option causes dysfunction with hdsp driver.
Turn it off as default.
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some modem codec seem to fail in the initialization, and this
stopped loading of the whole module although the audio is OK.
Since it's usually a non-fatal issue, the driver tries to proceed
to initialize now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix wrong error checks of *_ch_mode_put() in patch_realtek.c and
patch_analog.c. snd_hda_ch_mode_put() could return a positive
value for success, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes incorrect assignment of swap_rear,
which was broken since patch 'ymfpci - make rear channel swap optional'
It removes module_param rear_swap.
Signed-off-by: Glen Masgai <mimosius@gmx.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Use the roundup macro instead of manual calculations.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Don't include <linux/i2c-dev.h> as it's not needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Handle the return value of usb_register() in the module_init function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
add __devinitdata to struct whitelist, since it's used within
a __devinit function.
Add const attribute to iterator variable, too.
Compile-tested (no section warnings etc.) and run-tested
on vt8233, 2.6.18-mm3 (hopefully applies well to current ALSA).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
[PATCH] Generic HID layer - update MAINTAINERS
input/hid: Supporting more keys from the HUT Consumer Page
[PATCH] Generic HID layer - build: USB_HID should select HID
Fix the redirect packet of the router if the jiffies wraparound.
Signed-off-by: Li Yewang <lyw@nanjing-fnst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message logged in tcp_v4_inbound_md5_hash when the hash was expected
but not found was reversed.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
md5sig_info.alloced4 must be set to zero when freeing keys4, otherwise
it will not be alloc'd again when another key is added to the same
socket by tcp_v4_md5_do_add.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus has changed work queue structure and has not tested it with
connector compiled in, his changes break the build.
Attached patch fixes compilation error.
Patch is against commit 99f5e97181.
Thanks to Toralf Förster for pointing this out.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5906 PHY requires a special register bit to power down and up the
PHY.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hot-plug scripts can call tg3_open() as soon as register_netdev() is
called in tg3_init_one(). We need to call pci_set_drvdata() before
register_netdev(), and netif_carrier_off() needs to be moved to
tg3_open() to avoid race conditions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->link_config.orig_* values must be assigned during
tg3_set_settings() because these values will be used to setup the
link speed during tg3_open(). Without these assignments, the link
speed settings will be all messed by if tg3_set_settings() is called
when the device is down.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the menu dependencies in net/ipv6/netfilter/Kconfig
guard the entries in that file from the Kconfig GUI, this does
not prevent them from being selected still via "make oldconfig"
when IPV6 etc. is disabled.
So add explicit dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the configured MAC address instead of the permanent MAC address
for loopback frames.
Update version to 1.5.2.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Length was not calculated correctly if the NVRAM offset is on a non-
aligned offset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was an off-by-one bug in bnx2_tx_avail(). If the tx ring is
completely full, the producer and consumer indices may be apart by
256 even though the ring size is only 255. One entry in the ring is
unused and must be properly accounted for when calculating the number
of available entries. The bug caused the tx ring entries to be
reused by mistake, overwriting active entries, and ultimately causing
it to crash.
This bug rarely occurs because the tx ring is rarely completely full.
We always stop when there is less than MAX_SKB_FRAGS entries available
in the ring.
Thanks to Corey Kovacs <cjk@techma.com> and Andy Gospodarek
<agospoda@redhat.com> for reporting the problem and helping to collect
debug information.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rose_add_loopback_neigh uses kmalloc and the callers were ignoring the
error value. Rewrite to let the caller deal with the allocation. This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ax25_linkfail_register uses kmalloc and the callers were ignoring the
error value. Rewrite to let the caller deal with the allocation. This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ax25_listen_register to return something that's a sane error code,
then all callers to use it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ax25_protocol_register by ax25_register_pid which assumes the
caller has done the memory allocation. This allows replacing the
kmalloc allocations entirely by static allocations.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent fix 0506d4068b made obvious that
error values were not being propagated through the AX.25 stack. To help
with that this patch marks all kmalloc users in the AX.25, NETROM and
ROSE stacks as __must_check.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kmalloc+memset with kzalloc
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] longhaul compile fix.
[CPUFREQ] Advise not to use longhaul on VIA C7.
[CPUFREQ] set policy->curfreq on initialization
[CPUFREQ] Trivial cleanup for acpi read/write port in acpi-cpufreq.c
[CPUFREQ] fixes typo in cpufreq.c
Recent workqueue changes basically make this a formal requirement.
Also, move atomic32.o from lib-y to obj-y since it exports symbols
to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the correct variable and set policy->cur upon acpi-cpufreq
initialization to allow the userspace governor to be used as default.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
"sunkbd_enable(sunkbd, 0);" has no effect. Adding "sunkbd->enabled =
enable" in sunkbd_enable (obvious)
Signed-off-by: Fabrice Knevez <nuxdoors@cegetel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
