Wei Chong Tan reported a fast-PIT-calibration corner-case:
| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.
I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.
The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.
So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.
In other words:
- I'd like to move the PIT MSB check to after the last
iteration, rather than in every iteration
- I think we should comment on the fact that it's also a
serializing instruction and so 'fences in' the TSC read.
Here's a suggested replacement.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the vendor name (from c16) can be longer than 100 bytes (or missing a
terminating null), then the null is written past the end of vendor[].
Found with Parfait, http://research.sun.com/projects/parfait/
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Ying <ying.huang@intel.com>
MacBookPro5,1 is not able to reboot unless reboot=pci is set.
This patch forces it through a DMI quirk specific to this
device.
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <1249403971-6543-1-git-send-email-ozan@pardus.org.tr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With CONFIG_STACK_PROTECTOR turned on, VMI doesn't boot with
more than one processor. The problem is with the gs value not
being initialized correctly when registering the secondary
processor for VMI's case.
The patch below initializes the gs value for the AP to
__KERNEL_STACK_CANARY. Without this the secondary processor
keeps on taking a GP on every gs access.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org> # for v2.6.30.x
LKML-Reference: <1249425262.18955.40.camel@ank32.eng.vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The following fix was initially inspired by David Howells fix
few days back:
http://lkml.org/lkml/2009/7/9/109
However, Ingo disapproves such fixes as it's dangerous (it can
hide future, relevant warnings) - in something as
performance-uncritical.
So, initialize 'err' to '0' to work around a GCC false positive
warning:
http://lkml.org/lkml/2009/7/18/89
Signed-off-by: Subrata Modak<subrata@linux.vnet.ibm.com>
Cc: Sachin P Sant <sachinp@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20090721023226.31855.67236.sendpatchset@subratamodak.linux.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In uv_setup_irq(), the call to create_irq() initially assigns
IRQ vectors to cpu 0. The subsequent call to
assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to
another cpu and frees the cpu 0 vector - at least it will be
freed as soon as the "IRQ move" completes.
arch_enable_uv_irq() needs to send a cleanup IPI to complete
the IRQ move. Otherwise, assignment of GRU interrupts on large
systems (>200 cpus) will exhaust the cpu 0 interrupt vectors
and initialization of the GRU driver will fail.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090720142840.GA8885@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change SGI UV default apicid mode to "physical". This is
required to match settings in the UV hub chip.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143856.GA8905@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The UV BIOS has added additional MMR ranges that are mapped via
EFI virtual mode mappings. These ranges should be deleted from
ranges mapped by uv_system_init().
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143656.GA7698@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UV blades may not have any blade-local memory. Add a field
(nid) to the UV blade structure to indicates whether the node
has local memory. This is needed by the GRU driver (pushed
separately).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143507.GA7006@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Older versions of binutils did not accept the naked "ASSERT" syntax;
it is considered an expression whose value needs to be assigned to
something.
Reported-tested-and-fixed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The latest Apple MacBook (MacBook5,2) doesn't reboot successfully
under Linux; neither the EFI reboot method nor the default method
using the keyboard controller works (the system just hangs and doesn't
reset). However, the method using the "PCI reset register" at 0xcf9
does work.
This adds a quirk to detect this machine via DMI and force the
reboot_type to BOOT_CF9. With this it reboots successfully without
requiring a command-line option. Note that the EFI code forces
reboot_type to BOOT_EFI when the machine is booted via EFI, but this
overrides that since the core_initcall runs after the EFI
initialization code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19062.56420.501516.316181@cargo.ozlabs.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Startup code for i386 in arch/x86/kernel/head_32.S is using the
reference variable initial_code that is located in the .cpuinit.data
section. If CONFIG_HOTPLUG_CPU is enabled, startup code is not in an
init section and can be called later too. In this case the reference
initial_code must be kept too. This patch fixes this. See below for
the section mismatch warning.
WARNING: vmlinux.o(.cpuinit.data+0x0): Section mismatch in reference
from the variable initial_code to the function
.init.text:i386_start_kernel()
The variable __cpuinitdata initial_code references
a function __init i386_start_kernel().
If i386_start_kernel is only used by initial_code then
annotate i386_start_kernel with a matching annotation.
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1248716632-26844-1-git-send-email-robert.richter@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure
x86, amd: Don't probe for extended APIC ID if APICs are disabled
x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD"
x86-64: Fix bad_srat() to clear all state
x86, mce: Fix set_trigger() accessor
x86: Fix movq immediate operand constraints in uaccess.h
x86: Fix movq immediate operand constraints in uaccess_64.h
x86: Add reboot fixup for SBC-fitPC2
x86: Include all of .data.* sections in _edata on 64-bit
x86: Add quirk for Intel DG45ID board to avoid low memory corruption
Timer interrupts are excluded from being disabled during suspend. The
clock events code manages the disabling of clock events on its own
because the timer interrupt needs to be functional before the resume
code reenables the device interrupts.
The mfgpt timer request its interrupt without setting the IRQF_TIMER
flag so suspend_device_irqs() disables it as well which results in a
fatal resume failure.
Adding IRQF_TIMER to the interupt flags when requesting the mrgpt
timer interrupt solves the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Andres Salomon <dilinger@debian.org>
Cc: stable@kernel.org
* 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf: (31 commits)
perf_counter tools: Give perf top inherit option
perf_counter tools: Fix vmlinux symbol generation breakage
perf_counter: Detect debugfs location
perf_counter: Add tracepoint support to perf list, perf stat
perf symbol: C++ demangling
perf: avoid structure size confusion by using a fixed size
perf_counter: Fix throttle/unthrottle event logging
perf_counter: Improve perf stat and perf record option parsing
perf_counter: PERF_SAMPLE_ID and inherited counters
perf_counter: Plug more stack leaks
perf: Fix stack data leak
perf_counter: Remove unused variables
perf_counter: Make call graph option consistent
perf_counter: Add perf record option to log addresses
perf_counter: Log vfork as a fork event
perf_counter: Synthesize VDSO mmap event
perf_counter: Make sure we dont leak kernel memory to userspace
perf_counter tools: Fix index boundary check
perf_counter: Fix the tracepoint channel to perfcounters
perf_counter, x86: Extend perf_counter Pentium M support
...
If we've logically disabled apics, don't probe the PCI space for the
AMD extended APIC ID.
[ Impact: prevent boot crash under Xen. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reported-by: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
CONFIG_X86_THRESHOLD used in arch/x86/kernel/irqinit.c is always
undefined. Rename it to the correct name "CONFIG_X86_MCE_THRESHOLD".
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <4A667FD4.3010509@hitachi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Fix the condition checking the result of strchr() (which previously
could result in an oops), and make the function return the number of
bytes actively used.
[ Impact: fix oops ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <4A5F04B7020000780000AB59@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The CompuLab SBC-fitPC2 board needs to reboot via BIOS.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The .data.read_mostly and .data.cacheline_aligned sections
aren't covered by the _sdata .. _edata range on x86-64. This
affects kmemleak reporting leading to possible false
positives by not scanning the whole data section.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1247565175.28240.37.camel@pc1117.cambridge.arm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
AMI BIOS with low memory corruption was found on Intel DG45ID
board (Bug 13710). Add this board to the blacklist - in the
(somewhat optimistic) hope of future boards/BIOSes from Intel
not having this bug.
Also see:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Cc: ykzhao <yakui.zhao@intel.com>
Cc: alan@lxorguk.ukuu.org.uk
Cc: <stable@kernel.org>
LKML-Reference: <1247660169-4503-1-git-send-email-bug-track@fisher-privat.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when building 32-bit, I see this ..
arch/x86/kernel/pvclock.c:63:7: warning: "__x86_64__" is not defined
Signed-off-by: Dave Jones <davej@redhat.com>
LKML-Reference: <20090713201437.GA12165@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The variable apic_numaq placed in noninit section references the
function wakeup_secondary_cpu_via_nmi(), which is in __cpuinit
section. Thus causes a section mismatch warning. To avoid such
mismatch we mark apic_numaq as __refdata.
We were warned by the following warning:
WARNING: arch/x86/kernel/built-in.o(.data+0x932c): Section mismatch in
reference from the variable apic_numaq to the function
.cpuinit.text:wakeup_secondary_cpu_via_nmi()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120407p6b4f67dtf4d563155488188a@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The variable apic_es7000_cluster references the function __cpuinit
wakeup_secondary_cpu_via_mip() from a noninit section. So we've been
warned by the following warning. To avoid possible collision between
init/noninit, its best to mark the variable as __refdata.
We were warned by the following warning:
LD arch/x86/kernel/apic/built-in.o
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x198c): Section
mismatch in reference from the variable apic_es7000_cluster to the
function .cpuinit.text:wakeup_secondary_cpu_via_mip()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120404k6279a10ch5e9682432272706f@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I've attached a patch to remove the Pentium M special casing of
EMON and as noticed at least with my Pentium M the hardware PMU
now works:
Performance counter stats for '/bin/ls /var/tmp':
1.809988 task-clock-msecs # 0.125 CPUs
1 context-switches # 0.001 M/sec
0 CPU-migrations # 0.000 M/sec
224 page-faults # 0.124 M/sec
1425648 cycles # 787.656 M/sec
912755 instructions # 0.640 IPC
Vince suggested that this code was trying to address erratum
Y17 in Pentium-M's:
http://download.intel.com/support/processors/mobile/pm/sb/25266532.pdf
But that erratum (related to IA32_MISC_ENABLES.7) does not
affect perfcounters as we dont use this toggle to disable RDPMC
and WRMSR/RDMSR access to performance counters. We keep cr4's
bit 8 (X86_CR4_PCE) clear so unprivileged RDPMC access is not
allowed anyway.
Cc: Vince Weaver <vince@deater.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (50 commits)
perf report: Add "Fractal" mode output - support callchains with relative overhead rate
perf_counter tools: callchains: Manage the cumul hits on the fly
perf report: Change default callchain parameters
perf report: Use a modifiable string for default callchain options
perf report: Warn on callchain output request from non-callchain file
x86: atomic64: Inline atomic64_read() again
x86: atomic64: Clean up atomic64_sub_and_test() and atomic64_add_negative()
x86: atomic64: Improve atomic64_xchg()
x86: atomic64: Export APIs to modules
x86: atomic64: Improve atomic64_read()
x86: atomic64: Code atomic(64)_read and atomic(64)_set in C not CPP
x86: atomic64: Fix unclean type use in atomic64_xchg()
x86: atomic64: Make atomic_read() type-safe
x86: atomic64: Reduce size of functions
x86: atomic64: Improve atomic64_add_return()
x86: atomic64: Improve cmpxchg8b()
x86: atomic64: Improve atomic64_read()
x86: atomic64: Move the 32-bit atomic64_t implementation to a .c file
x86: atomic64: The atomic64_t data type should be 8 bytes aligned on 32-bit too
perf report: Annotate variable initialization
...
Stephen reported that his DL585 G2 needed noapic after 2.6.22 (?)
Dann bisected it down to:
commit 30a18d6c3f
Date: Tue Feb 19 03:21:20 2008 -0800
x86: multi pci root bus with different io resource range, on
64-bit
It turns out that:
1. that AMD-based systems have two HT chains.
2. BIOS doesn't allocate resources for BAR 6 of devices under 8132 etc
3. that multi-peer-root patch will try to split root resources to peer
root resources according to PCI conf of NB
4. PCI core assigns unassigned resources, but they overlap with BARs
that are used by ioapic addr of io4 and 8132.
The reason: at that point ioapic address are not inserted yet. Solution
is to insert ioapic resources into the tree a bit earlier.
Reported-by: Stephen Frost <sfrost@snowman.net>
Reported-and-Tested-by: dann frazier <dannf@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@jbarnes-g45.(none)>
Ingo noticed that both AMD and P6 call
x86_pmu_disable_counter() on *_pmu_enable_counter(). This is
because we rely on the side effect of that call to program
the event config but not touch the EN bit.
We change that for AMD by having enable_all() simply write
the full config in, and for P6 by explicitly coding it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The P6 doesn't seem to support cache ref/hit/miss counts, so
we extend the generic hardware event codes to have 0 and -1
mean the same thing as for the generic cache events.
Furthermore, it turns out the 0 event does not count
(that is, its reported that on PPro it actually does count
something), therefore use a event configuration that's
specified not to count to disable the counters.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add basic P6 PMU support. The P6 uses the EVNTSEL0 EN bit to
enable/disable both its counters. We use this for the
global enable/disable, and clear all config bits (except EN)
to disable individual counters.
Actual ia32 hardware doesn't support lfence, so use a locked
op without side-effect to implement a full barrier.
perf stat and perf record seem to function correctly.
[a.p.zijlstra@chello.nl: cleanups and complete the enable/disable code]
Signed-off-by: Vince Weaver <vince@deater.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <Pine.LNX.4.64.0907081718450.2715@pianoman.cluster.toy>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide support for family 0xf processors with 2 P-states
below the elevator voltage. Remove the checks that prevent
this configuration from being supported and increase the
transition voltage to prevent errors during the transition.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix usage of bios intcall()
x86: Remove unused function lapic_watchdog_ok()
x86: Remove unused variable disable_x2apic
x86, kvm: Fix section mismatches in kvm.c
x86: Add missing annotation to arch/x86/lib/copy_user_64.S::copy_to_user
x86: Fix fixmap page order for FIX_TEXT_POKE0,1
amd-iommu: set evt_buf_size correctly
amd-iommu: handle alias entries correctly in init code
x86: Fix printk call in print_local_apic()
x86: Declare check_efer() before it gets used
x86: Mark device_nb as static and fix NULL noise
x86: Remove double declaration of MSR_P6_EVNTSEL0 and MSR_P6_EVNTSEL1
xen: Use kcalloc() in xen_init_IRQ()
x86: Fix fixmap ordering
x86: Fix symbol annotation for arch/x86/lib/clear_page_64.S::clear_page_c
lapic_watchdog_ok() is a global function but no one is using it.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1246554335.2242.29.camel@jaswinder.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
setup_nox2apic() is writing 1 to disable_x2apic but no one is reading it.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
LKML-Reference: <1246554239.2242.27.camel@jaswinder.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The function paravirt_ops_setup() has been refering the
variable no_timer_check, which is a __initdata. Thus generates
the following warning. paravirt_ops_setup() function is called
from kvm_guest_init() which is a __init function. So to fix
this we mark paravirt_ops_setup as __init.
The sections-check output that warned us about this was:
LD arch/x86/built-in.o
WARNING: arch/x86/built-in.o(.text+0x166ce): Section mismatch in
reference from the function paravirt_ops_setup() to the variable
.init.data:no_timer_check
The function paravirt_ops_setup() references
the variable __initdata no_timer_check.
This is often because paravirt_ops_setup lacks a __initdata
annotation or the annotation of no_timer_check is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Acked-by: Avi Kivity <avi@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <b9df5fa10907012240y356427b8ta4bd07f0efc6a049@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/iommu-2.6: (38 commits)
intel-iommu: Don't keep freeing page zero in dma_pte_free_pagetable()
intel-iommu: Introduce first_pte_in_page() to simplify PTE-setting loops
intel-iommu: Use cmpxchg64_local() for setting PTEs
intel-iommu: Warn about unmatched unmap requests
intel-iommu: Kill superfluous mapping_lock
intel-iommu: Ensure that PTE writes are 64-bit atomic, even on i386
intel-iommu: Make iommu=pt work on i386 too
intel-iommu: Performance improvement for dma_pte_free_pagetable()
intel-iommu: Don't free too much in dma_pte_free_pagetable()
intel-iommu: dump mappings but don't die on pte already set
intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()
intel-iommu: Introduce domain_sg_mapping() to speed up intel_map_sg()
intel-iommu: Simplify __intel_alloc_iova()
intel-iommu: Performance improvement for domain_pfn_mapping()
intel-iommu: Performance improvement for dma_pte_clear_range()
intel-iommu: Clean up iommu_domain_identity_map()
intel-iommu: Remove last use of PHYSICAL_PAGE_MASK, for reserving PCI BARs
intel-iommu: Make iommu_flush_iotlb_psi() take pfn as argument
intel-iommu: Change aligned_size() to aligned_nrpages()
intel-iommu: Clean up intel_map_sg(), remove domain_page_mapping()
...
fix hang with HIGHMEM_64G and 32bit resource. According to hpa and
Linus, use (resource_size_t)-1 to fend off big ranges.
Analyzed by hpa
Reported-and-tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The setting of this variable got lost during the suspend/resume
implementation. But keeping this variable zero causes a divide-by-zero
error in the interrupt handler. This patch fixes this.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
An alias entry in the ACPI table means that the device can send requests to the
IOMMU with both device ids, its own and the alias. This is not handled properly
in the ACPI init code. This patch fixes the issue.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
About every callchains recorded with perf record are filled up
including the internal perfcounter nmi frame:
perf_callchain
perf_counter_overflow
intel_pmu_handle_irq
perf_counter_nmi_handler
notifier_call_chain
atomic_notifier_call_chain
notify_die
do_nmi
nmi
We want ignore this frame as it's not interesting for
instrumentation. To solve this, we simply ignore every frames
from nmi context.
New example of "perf report -s sym -c" after this patch:
9.59% [k] search_by_key
4.88%
search_by_key
reiserfs_read_locked_inode
reiserfs_iget
reiserfs_lookup
do_lookup
__link_path_walk
path_walk
do_path_lookup
user_path_at
vfs_fstatat
vfs_lstat
sys_newlstat
system_call_fastpath
__lxstat
0x406fb1
3.19%
search_by_key
search_by_entry_key
reiserfs_find_entry
reiserfs_lookup
do_lookup
__link_path_walk
path_walk
do_path_lookup
user_path_at
vfs_fstatat
vfs_lstat
sys_newlstat
system_call_fastpath
__lxstat
0x406fb1
[...]
For now this patch only solves the problem in x86-64.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1246474930-6088-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
