Restore function signatures from bool to int so that we can report
memory allocation failures or similar using -ENOMEM rather than
always having to pass -EINVAL back.
This semantic patch may not be too precise (checking for functions
that use xt_mtchk_param rather than functions referenced by
xt_match.checkentry), but reviewed, it produced the intended result.
// <smpl>
@@
type bool;
identifier check, par;
@@
-bool check
+int check
(struct xt_mtchk_param *par) { ... }
// </smpl>
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The first argument to NF_HOOK* is an nfproto since quite some time.
Commit v2.6.27-2457-gfdc9314 was the first to practically start using
the new names. Do that now for the remaining NF_HOOK calls.
The semantic patch used was:
// <smpl>
@@
@@
(NF_HOOK
|NF_HOOK_THRESH
)(
-PF_BRIDGE,
+NFPROTO_BRIDGE,
...)
@@
@@
NF_HOOK(
-PF_INET6,
+NFPROTO_IPV6,
...)
@@
@@
NF_HOOK(
-PF_INET,
+NFPROTO_IPV4,
...)
// </smpl>
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Supplement to 1159683ef4.
Downgrade the log level to INFO for most checkentry messages as they
are, IMO, just an extra information to the -EINVAL code that is
returned as part of a parameter "constraint violation". Leave errors
to real errors, such as being unable to create a LED trigger.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Remove unused headers in net/ipv4/netfilter/nf_nat_h323.c
Signed-off-by: Zhitong Wang <zhitong.wangzt@alibaba-inc.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Remove unused headers in net/ipv6/netfilter/ip6t_LOG.c
Signed-off-by: Zhitong Wang <zhitong.wangzt@alibaba-inc.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ENOMEM is a very obvious error code (cf. EINVAL), so I think we do not
really need a warning message. Not to mention that if the allocation
fails, the user is most likely going to get a stack trace from slab
already.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
This member is taking up a "long" per match, yet is only used by one
module out of the roughly 90 modules, ip6t_hbh. ip6t_hbh can be
restructured a little to accomodate for the lack of the .data member.
This variant uses checking the par->match address, which should avoid
having to add two extra functions, including calls, i.e.
(hbh_mt6: call hbhdst_mt6(skb, par, NEXTHDR_OPT),
dst_mt6: call hbhdst_mt6(skb, par, NEXTHDR_DEST))
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The matches can have .family = NFPROTO_UNSPEC, and though that is not
the case for the touched modules, it seems better to just use the
nfproto from the caller.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
I do not see a point of allowing the MAC module to work with devices
that don't possibly have one, e.g. various tunnel interfaces such as
tun and sit.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
XT_ALIGN is already applied on matchsize/targetsize in x_tables.c,
so it is not strictly needed in the extensions.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Remove unused headers in net/netfilter/nfnetlink.c
Signed-off-by: Zhitong Wang <zhitong.wangzt@alibaba-inc.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
One of the problems with the way xt_recent is implemented is that
there is no efficient way to remove expired entries. Of course,
one can write a rule '-m recent --remove', but you have to know
beforehand which entry to delete. This commit adds reaper
logic which checks the head of the LRU list when a rule
is invoked that has a '--seconds' value and XT_RECENT_REAP set. If an
entry ceases to accumulate time stamps, then it will eventually bubble
to the top of the LRU list where it is then reaped.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Two arguments for combining the two:
- xt_mark is pretty useless without xt_MARK
- the actual code is so small anyway that the kmod metadata and the module
in its loaded state totally outweighs the combined actual code size.
i586-before:
-rw-r--r-- 1 jengelh users 3821 Feb 10 01:01 xt_MARK.ko
-rw-r--r-- 1 jengelh users 2592 Feb 10 00:04 xt_MARK.o
-rw-r--r-- 1 jengelh users 3274 Feb 10 01:01 xt_mark.ko
-rw-r--r-- 1 jengelh users 2108 Feb 10 00:05 xt_mark.o
text data bss dec hex filename
354 264 0 618 26a xt_MARK.o
223 176 0 399 18f xt_mark.o
And the runtime size is like 14 KB.
i586-after:
-rw-r--r-- 1 jengelh users 3264 Feb 18 17:28 xt_mark.o
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Convert DPRINTK, commonly used for debugging, to netif_<level>
Remove #define PFX
Use #define pr_fmt
Consistently use no periods for non-sentence logging messages
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3ae clause 45 specifies a somewhat modified MDIO protocol
for use by 10GIGE phys. The main change is a 21 bit address split into
a 5 bit device ID and a 16 bit register offset. The definition is designed
so that normal and extended devices can run on the same MDIO bus.
Extend mdio-bitbang to do the new protocol. At the MDIO bus level the
protocol is requested by or'ing MII_ADDR_C45 into the register offset.
Make phy_read/phy_write/etc pass a full 32 bit register offset.
This does not attempt to make the phy layer support C45 style PHYs, just
to provide the MDIO bus support.
Tested against a Broadcom 10GE phy with ID 0x206034, and several
Broadcom 10/100/1000 Phys in normal mode.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the PCI runtime power management framework to add basic PCI
runtime PM support to the e1000e driver. Namely, make the driver
suspend the device when the link is off and set it up for generating
a wakeup event after the link has been detected again. [This
feature is disabled until the user space enables it with the help of
the /sys/devices/.../power/contol device attribute.]
Based on a patch from Matthew Garrett.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the PCI runtime power management framework to add basic PCI
runtime PM support to the r8169 driver. Namely, make the driver
suspend the device when the link is not present and set it up for
generating a wakeup event after the link has been detected again.
[This feature is disabled until the user space enables it with the
help of the /sys/devices/.../power/contol device attribute.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx4, using char * to store mc address in private structure instead.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure this is correct.
It changes logging macros from:
dev_<level>(&ks->spidev->dev,
to
netdev_<level>(ks->netdev,
Comments?
Use netdev_<level>
Use netif_<level>
Use pr_<level>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Add missing line to message in ks8851_remove
Change kmalloc/memset(,0) to kzalloc
Remove ks_<level> macros
Consolidation code into set_media_state
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward port commit
fc477e160af086f6e30c3d4fdf5f5c000d29beb5
from git://tipc.cslab.ericsson.net/pub/git/people/allan/tipc.git
Origional commit message:
Allow retransmission of cloned buffers
This patch fixes an issue with TIPC's message retransmission logic
that prevented retransmission of clone sk_buffs. Originally intended
as a means of avoiding wasted work in retransmitting messages that
were still on the driver's outbound queue, it also prevented TIPC
from retransmitting messages through other means -- such as the
secondary bearer of the broadcast link, or another interface in a
set of bonded interfaces. This fix removes existing checks for
cloned sk_buffs that prevented such retransmission.
Origionally-Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward port commit 29eb572941501c40ac6e62dbc5043bf9ee76ee56
from git://tipc.cslab.ericsson.net/pub/git/people/allan/tipc.git
Origional commit message:
Increase frequency of load distribution over broadcast link
This patch enhances the behavior of TIPC's broadcast link so that it
alternates between redundant bearers (if available) after every
message sent, rather than after every 10 messages. This change helps
to speed up delivery of retransmitted messages by ensuring that
they are not sent repeatedly over a bearer that is no longer working,
but not yet recognized as failed.
Tested by myself in the latest net-2.6 tree using the tipc sanity test suite
Origionally-signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
bcast.c | 35 ++++++++++++++---------------------
1 file changed, 14 insertions(+), 21 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
`ip -s link` shows interface counters truncated to 32 bit. This is
because interface statistics are transported only in 32-bit quantity
to userspace. This commit adds a new IFLA_STATS64 attribute that
exports them in full 64 bit.
References: http://lkml.indiana.edu/hypermail/linux/kernel/0307.3/0215.html
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
