The keymap for this remote had duplicated labels for different keys,
which resulted in those key pairs being unable to function as different
inputs.
Signed-off-by: Emil Georgiev <emilonlinester@gmail.com>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In transfer/replay mode the frontend lock status was never updated.
This caused a 'black screen' if VDR switched from transfer mode to
live mode on the same transponder.
Thanks to Marco Schluessler for spotting the problem.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is no reason why cx25840-firmware.c would need to include
<linux/i2c-algo-bit.h>.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
SA_* interrupt flags are being phased out, update to newer flags.
Thanks to Maarten Maathuis for pointing this out to me.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_V4L1 is needed to get tvaudio to be built. Stupid really as ivtv is only
using the v4l2 API to communicate with tvaudio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_CX25840 was missing in the ivtv dependencies. VIDEO_TLV320AIC23B
was removed since it isn't used by ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The code the i2c transactions was leftover from the old V4L-based ATSC
driver. It did too little with too much code. It is re-written to
remove unnecessary parameters and be more efficient. A demod register
can now be read with one function call, instead of repeating a dozen line
block of code each time.
There were msleep()'s, which appear to be unnecessary, spread around all
the I2C transactions. These have been removed. Reading SNR used to take
about 130 ms, now it's down to 1.8 ms.
Reads from the demodulator's registers do not return correct results
sometimes. Adding or removing the delays in the I2C transactions did not
appear to effect the probability of failure. If anything, the
transactions without delays were less likely to fail, but since far more
transactions could be made per second the number of failures per hour was
greater.
To increase reliability, the SNR and get_params functions will now retry
once if they get bad data back. This appears to have reduced the
probability of failure to effectively zero.
Some error messages are cleaned up or given KERN_* levels when they were
missing.
or51132_setmode() wasn't returning correct error codes, which is fixed as
well.
CC: Rusty Scott <rustys@ieee.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When trying to use a Hauppauge Nova-T Stick on a big-endian architecture
(such as powerpc) no frontend can be attached.
The attached patch fixes this problem by removing two lines in
dib0700_ctrl_rd() that try to correct the endianess on two values that
already are correct:
- /* think about swapping here */
- value = le16_to_cpu(value);
- index = le16_to_cpu(index);
With this simple patch this dvb hardware works great, thanks to anyone
involved for the good work. :)
Signed-off-by: Dennis Ranke <mail@exoticorn.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added USB_PID_PCTV_450E to the 'usb_device_id ttusb2_table' and an entry in the
.devices table. The 400e driver now supports the 'Pinnacle PCTV Sat Pro USB
(450e)' with USB_ID 2304:0222.
Signed-off-by: Christophe Cattelain <xof@skynet.be>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The i2c data buffer in tda827xa_set_params was 1 byte too short
- saa7134-dvb now gives an error mesage if tda827x could not be attached
- coding style fix in tda1004x.c
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The code of the dvb-pll driver and the lgh06xf driver is nearly
identical. The main difference is that the lgh06xf driver would set the
AGC TOP value on every tune call. The dvb-pll driver now has the ability
to set the AGC TOP when the front-end device is opened, which is a better
way to go about it. By using this ability of dvb-pll, the lgh06xf driver
is made unnecessary.
There is one other difference. dvb-pll will probe for the presence of an
I2C pll chip by doing a one byte read, the lgh06xf driver did not do
this. In some devices the PLL is not reachable over I2C at the timer the
tuner is attached. Some more initialization, such as firmware loading,
must take place first. None of the devices using a LG-H06xF should have
this problem.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some tuners need or benefit from initialization, to change certain
settings from their power on default values.
Typically, tuners with TUA603x PLLs can benefit from setting the AGC TOP
value to something else. This patch includes code to set the AGC TOP to
103 dBuV for the Thomson DTT-761x tuners, which I have experimentally
verified gives the best SNR readings, increasing SNR by about 0.19 dB
over the default value.
Other tuners can make use of this as well. For example, the separate LG
TDVS-H06xF driver's only difference from dvb-pll is this same setting of
AGC TOP value.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A number of drivers selected DVB_PLL when they did not need it, and some
that did need it did not select it.
The DVB_PLL option is given a name and help text, so that it will show up
in the config menu. DVB_PLL support can be turned on if an out-of-tree
driver needs it.
The standard dvb fe customization support is added to dvb-pll.h. Since
all modules which select DVB_PLL do so unconditionally, it is not
possible to turn dvb-pll off when an enabled module selects it, unlike
most of the other frontend/tuner drivers. This is because the users of
dvb-pll have static references to dvb-pll symbols other than the attach
function. If these references are removed, then dvb-pll will be
disablable as the other frontend/tuner drivers are.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Better to use sizeof() to get the size of the output buffer for the tuner
name, instead of just hard coding 128.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It took three core maintainers, over four years of work, eight new i2c
modules, eleven new V4L2 ioctls, three new DVB video ioctls, a Sliced
VBI API, a new MPEG encoder API, an enhanced DVB video MPEG decoding
API, major YUV/OSD contributions from Ian and John, web/wiki/svn/trac
support from Axel Thimm, (hardware) support from Hauppauge, support and
assistance from the v4l-dvb people and the many, many users of ivtv to
finally make it possible to merge this driver into the kernel.
Thank you all!
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for MSC_RAW and MSC_SCAN remote control events.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The documentation of Several miscellaneous commands was updated.
As a result of which the CX2341X_ENC_UNKNOWN command was renamed to
CX2341X_ENC_SET_VERT_CROP_LINE.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch contains the last set of changes to the budget-ci IR
handling which makes it use the repeat handling of the input subsystem.
This allows some code simplification, makes sure that repeat key presses
are reported as such and also allows the "debounce" hack to be removed
altogether.
In addition a couple of static variables were removed which would have
confused the IR code if more than one card is used.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Infrared remote control support rewritten.
Now each device provides its own event device, keymap, protocol,
inversion and address setting.
EVIOCGKEYCODE and EVIOCSKEYCODE ioctls are supported to read/modify
a keymap. Keymaps may be loaded using
- input tools (keyb etc.)
- av7110_loadkeys (obsolete, for backward compatibility)
New command line parameters:
- ir_protocol: select infrared protocol: 0 RC5, 1 RCMM (default)
- ir_inversion: signal inversion: 0 not inverted (default), 1 inverted
- ir_device_mask: bitmask of infrared devices (default: accept all)
Those parameters may be set anytime.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is a Lifeview Duo with a different ID
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch move the assignment of the tuner config and the callback
before the check whether it is called in the attach inform.
This solves a module load order issue
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change supplies a more generic version of the tuner callback.
The tuner struct now has a function pointer
int (*tuner_callback) (void *dev, int command, int arg)
additionally to a int config parameter.
both can be set through the TUNER_SET_TYPE_ADDR client call.
Note that the meaning of the parameters depend on the tuner type.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is for better consistency with other drivers
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The hardware is completely initialized afterwards, especially the
tda10046 has its firmware - which is also necessary in analog mode
of some hybrid boards.
Calling the sleep function afterwards saves power and definitely puts
hybrid boards into analog mode without additional code elsewere.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The parameters for minimum and maximum frequency were missing.
Also added mail addresses of the module authors.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change sets the tda827x to sleep mode right after attach in dvb
mode. It is just to save power. For the same reason, the ADC of the
tda10046 gets turned off in sleep mode.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During tuner attach, the pointers to host dev structure
are not set yet, so the I2c adapter needs to be accessed differently.
This patch also does some minor cleanup in the saa7134-dvb module.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch moves the tda827x dvb tuning code to a separate module
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are card variants supporting FM radio through tda8275.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In older versions, this was used to decide whether to boot from
eeprom or file. This is no longer necessary but the check helps to avoid
an oops with misconfigured cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains
- new tuning code for the tda827xa silicon tuner.
- controls the preamplifier of some boards with this tuner.
- support for the Philips Tiger S hybrid DVB-T reference design.
- reworked the saa7134-dvb modulue to get rid of most of the
small board specific functions.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These entries mainly are to support configurations of the tda827x
silicon tuner with a preamplifier.
The values can be set throgh the attach inform or through
the extended TUNER_SET_TYPE_ADDR client call. The function pointer
will only be updated if the parameter is not NULL.
Since a typecast is necessary to set the pointer, i added a typedef for
this pointer (tuner_gpio_func_t) in tuner.h
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This function allows to set, clear and tristate the GPIO ports.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are the following changes:
- separate configuration of IF and GPIOs.
- set GPIOs before firmware load. This helps to avoid I2C address
collisions.
- if desired invert GPIOs at sleep (automatic return to analog mode of card).
- added 3 tuner configuration bytes to config stuct.
- added i2c gate address to config struct.
- moved _state struct declaration to header file to make it accessible
on board layer.
- added "conf_probed" to the state struct to allow i.e. probing for correct
tuner version.
- changed firmware load mechanism to always:
+ check if already loaded
+ try to boot from eeprom
+ try downlad from host
- corrected name of tda10046 firmware image (backward compatible).
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23415 adds some extra features that this DVB decoding API did
not support. This API has been expanded to support the required
features. Both source and binary backwards compatibility is kept
intact by these changes. So existing applications are not affected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_G_CHIP_IDENT improves debugging of card problems: it can be
used to detect which chips are on the board and based on that information
selected register dumps can be made, making it easy to debug complicated
media chips containing tens or hundreds of registers.
This ioctl replaces the internal VIDIOC_INT_G_CHIP_IDENT ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for loading cx88-dvb and cx88-blackbird
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
added support for deferred module requesting to cx88
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
