We assumed only bios with bi_idx == 0 would end up
in drbd_make_request().
That is wrong.
At least device mapper, in __clone_and_map(), may submit
clones only covering a partial bio, but sharing
the original bvec, by adjusting bi_idx and relevant
other bio members of the clone.
We used __bio_for_each_segment() in various places,
even though that is documented as
* drivers should not use the __ version unless they _really_ want to
* run through the entire bio and not just pending pieces
Impact: we would send the full bio bvec, even for the clone
with bi_idx > 0, which will cause data corruption on the
peer (because we submit wrong data at the clone offset),
and will cause a DRBD protocol error, disconnect/reconnect
and resync (thus fixing the corruption),
because the next package header would be expected right
in the middle of the sent data, causing DRBD magic mismatch.
Fix: drop the assert, and use bio_for_each_segment()
instead of the __ version.
Conflicts:
drbd/drbd_tracing.c
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a SyncTarget node gets a P_RS_DATA_REPLY before a P_DATA packet
for the same sector, it simply submits these two IO requests.
This is be possible because on the SyncSource node, the data of the
P_RS_DATA_REPLY packet was read from disk. Immediately after that a
write request from upper layers came in.
The disk scheduler or even the "hardware" queues on the disk drive might
reorder these writes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When we have a write request and a state change C_WF_BITMAP_S -> C_SYNC_SOURCE
at the same time, and it happens that the line
remote = remote && drbd_should_do_remote(s);
stills sees C_WF_BITMAP_S, and
send_oos = rw == WRITE && drbd_should_send_oos(s);
already sees C_SYNC_SOURCE both are 0.
This causes the write to not be mirrored, but marked as out-of-sync on the
Sync_Source node.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Without this, iostat frequently sees bogus svctime and >= 100% "utilization".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_accept was modelled after kernel_accept
with drbd commit 53eb779 in July 2008.
Only, kernel_accept was then broken, and only fixed later
with kernel commit 1b08534e in Dec 2008:
net: Fix module refcount leak in kernel_accept()
Impact: protocol families provided as modules, e.g. ipv6 or ib_sdp,
would soon have their reference count become negative, preventing
them from being unloaded (likely), or worse, hit zero without actually
being unused, allowing them to be unloaded while still in use (unlikely,
but if triggered, causing a kernel crash).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the backing device is already frozen during attach, we failed
to recognize that. The current disk-timeout code works on top
of the drbd_request objects. During attach we do not allow IO
and therefore never generate a drbd_request object but block
before that in drbd_make_request().
This patch adds the timeout to all drbd_md_sync_page_io().
Before this patch we used to go from D_ATTACHING directly
to D_DISKLESS if IO failed during attach. We can no longer
do this since we have to stay in D_FAILED until all IO
ops issued to the backing device returned.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
I.e. in C_WF_REPORT_PARAMS or in C_WF_CONNECTION.
Sending may already work in these cstates, but the peer still expects
the HandShake / ConnectionFeatures packet.
Actually triggered by the Testuite on kugel.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the asender thread, or request_timer_fn(), or some other part of
the code, decided to drop the connection (because of timeout or other),
but the receiver just now was processing a P_STATE packet, there was a
chance that receive_state() would do a hard state change
"re-establishing" an already failed connection without additional handshake.
Log excerpt:
Remote failed to finish a request within ko-count * timeout
peer( Secondary -> Unknown ) conn( Connected -> Timeout ) pdsk( UpToDate -> DUnknown )
asender terminated
...
peer( Unknown -> Secondary ) conn( Timeout -> Connected ) pdsk( DUnknown -> UpToDate ) peer_isp( 0 -> 1 )
...
Connection closed
peer( Secondary -> Unknown ) conn( Connected -> Unconnected ) pdsk( UpToDate -> DUnknown ) peer_isp( 1 -> 0 )
receiver terminated
Impact:
while the connection state is erroneously "Connected",
requests may be queued and even sent,
which would never be acknowledged,
and may have been missed by the cleanup.
These requests would never be completed.
The next drbd_suspend_io() will then lock up,
waiting forever for these requests to complete.
Fixed in several code paths:
Make sure the connection state is NetworkFailure or worse
before starting the cleanup in drbd_disconnect().
This should make sure the cleanup won't miss any requests.
Disallow receive_state() to "upgrade" the connection state
from an error state. This will make sure the "illegal" state
transition won't happen.
For all connection failure states,
relax the safe-guard in sanitize_state() again
to silently mask out those state changes
(e.g. Timeout -> Connected becomes Timeout -> Timeout).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_try_clear_on_disk_bm() has a sanity check for the number of blocks
left to be resynced (rs_left) in the current resync extent.
If it detects a mismatch, it complains, and forces a disconnect using
drbd_force_state(mdev, NS(conn, C_DISCONNECTING));
Unfortunately, this may be called while holding the req_lock,
and drbd_force_state() want's to aquire that lock itself. Deadlock.
Don't force a disconnect, but fix up rs_left by recounting and
reassigning the number of dirty blocks in that extent.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This bug might have caused troubles if disk-barriers and the ahead-behind
more are enabled at the same time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
DRBD state changes schedule after_state_ch() actions to a worker thread,
which decides on the old and new states of that change, whether to send
an informational state update packet (P_STATE) to the peer.
If it decides to drbd_send_state(), it would however always send the
_curent_ state, which, if a second state change happens before the
after_state_ch() of the first ran, may "fast-forward" the peer's view
about this node. In most cases that is harmless, but sometimes this can
confuse DRBD, for example into not actually starting a necessary resync
if you do a very tight detach/attach loop on a Connected Secondary.
Fix this by always sending the "new" state of the respective state
transition which scheduled this after_state_ch() work.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When detaching, even cleanly detaching due to administrator request,
we always go through D_FAILED before we become D_DISKLESS.
Don't let that state change race with an in-flight meta data IO,
or that one might think it actually experienced an IO error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_state_lock() is only there to serialize cluster wide state
changes. Testing the local disk state needs to happen while
holding the global_state_lock.
Otherwise you might see something like this (Oct 6 on kugel)
14:20:24 drbd0: conn( WFSyncUUID -> Connected ) disk( Inconsistent -> Failed )
14:20:24 drbd0: helper command: /sbin/drbdadm before-resync-target minor-0 exit code 0 (0x0)
14:20:24 drbd0: conn( Connected -> SyncTarget ) disk( Failed -> Inconsistent )
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We have one pre-allocated page to do certain synchronous meta data IO with,
using it is serialized like so:
drbd_md_get_buffer();
drbd_md_sync_page_io();
drbd_md_sync_page_io();
...
drbd_md_put_buffer();
In drbd_md_sync_page_io() there is an
ASSERT(atomic_read(&mdev->md_io_in_use) == 1);
We want to be able to timeout on unresponsive lower level devices, so we
can "detach" in that case. Inside drbd_md_sync_page_io() we grab an extra
reference, to not have a dangling pointer in case a delayed IO eventually
does still complete, even after we "detached" already.
We need to put the extra reference before we signal completion from the
completion handler, or the second drbd_md_sync_page_io() above may
trigger the assert (reference count still 2).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With sync-after dependencies, given "lucky" timing of pause/unpause
events, and the end of an empty (0 bits set) resync was sometimes not
detected on the SyncTarget, leading to a "stalled" SyncSource state.
Fixed this by expecting not only "Inconsistent -> UpToDate" but also
"Consistent -> UpToDate" transitions for the peer disk state
to end a resync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we get into the C_BROKEN_PIPE cstate once, the state engine set the
thi->t_state of the receiver thread to restarting. But with the while loop
in drbdd_init() a new connection gets established. After the call into
drbdd() returns immediately since the thi->t_state is not RUNNING. The
restart of drbd_init() then resets thi->t_state to RUNNING.
I.e. after entering C_BROKEN_PIPE once, the next successful established
connection gets wasted.
The two parts of the fix:
* Do not cause the thread to restart if we detect the issue
with the sockets while we are in C_WF_CONNECTION.
* Make sure that all actions that would have set us to C_BROKEN_PIPE
happen before the state change to C_WF_REPORT_PARAMS.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
...when the peer has inconsistent data. In that case we failed to
clear the susp_nod flag. When the local disk was attached again
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now, the new edition of the clause only fires if a diskless
peer gets promoted.
This is a fixup for "drbd: Delayed creation of current-UUID".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Bitmap IO may happend in the context of an application write,
in the generic block IO path. We need to use GFP_NOIO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the disk-timeout is active, and it expires for a single request,
we consider the local disk as D_FAILED. Note: With this change,
I made both timeout based state transitions HARD state transitions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last bunch of commits prepared the 'detach from tar pit' feature.
With that we can be for long time in disk state FAILED. We need
to accept new IO requests during that time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The new function drbd_md_get_buffer() aborts waiting for the buffer
in case the disk failes in the meantime.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Regression introduced with 8.3.11 commit:
drbd: Take a more conservative approach when deciding max_bio_size
Never ever tell an older drbd, that we support more than 32KiB
in a single data request (packet).
Never believe an older drbd, that is supports more than 32KiB
in a single data request (packet)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The reason for this change is that, with when doing
'drbdadm invalidate' on a disconnected resource caused
an "implicitly set pdsk from UpToDate to DUnknown" message,
which was missleading.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Allow up to 300 centi-seconds to be configured for the "ping timeout".
There may be setups where heavy congestion, huge buffers, and asymmetric
bandwidth limitations may need a "huge" ping-timeout as work-around
for "spurious connection loss" problems.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Fix warnings of the following nature in the drbd header:
In file included from drivers/block/drbd/drbd_bitmap.c:32:
drivers/block/drbd/drbd_int.h: In function 'drbd_get_syncer_progress':
drivers/block/drbd/drbd_int.h:2234: warning: comparison is always false due to limited range of data
where mdev->rs_total (an unsigned long) is being compared to 1ULL << 32, which
is always false on a 32-bit machine.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
It is not "to small", but "too small".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
For large resync rates, seq_printf_with_thousands_grouping()
accidentally only produced Y,000,00Y, instead of the real numbers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPnb50AAoJEHm+PkMAQRiGAE0H/A4zFZIUGmF3miKPDYmejmrZ
oVDYxVAu6JHjHWhu8E3VsinvyVscowjV8dr15eSaQzmDmRkSHAnUQ+dB7Di7jLC2
MNopxsWjwyZ8zvvr3rFR76kjbWKk/1GYytnf7GPZLbJQzd51om2V/TY/6qkwiDSX
U8Tt7ihSgHAezefqEmWp2X/1pxDCEt+VFyn9vWpkhgdfM1iuzF39MbxSZAgqDQ/9
JJrBHFXhArqJguhENwL7OdDzkYqkdzlGtS0xgeY7qio2CzSXxZXK4svT6FFGA8Za
xlAaIvzslDniv3vR2ZKd6wzUwFHuynX222hNim3QMaYdXm012M+Nn1ufKYGFxI0=
=4d4w
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc5' into for-3.5/core
The core branch is behind driver commits that we want to build
on for 3.5, hence I'm pulling in a later -rc.
Linux 3.4-rc5
Conflicts:
Documentation/feature-removal-schedule.txt
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix for an issue causing hibernation to hang on systems with highmem (that
practically means i386) due to broken memory management (bug introduced in 3.2,
so -stable material) and PM documentation update making the freezer
documentation follow the code again after some recent updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=HaVL
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Fix for an issue causing hibernation to hang on systems with highmem
(that practically means i386) due to broken memory management (bug
introduced in 3.2, so -stable material) and PM documentation update
making the freezer documentation follow the code again after some
recent updates."
* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer / Docs: Update documentation about freezing of tasks
PM / Hibernate: fix the number of pages used for hibernate/thaw buffering
The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).
We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4ab ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit
kernel.
But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.
As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9de.
With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other. At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation. Ugly, ugly.
However, a prettier solution exists now thanks to the packetized pipe
mode. By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown
away.
This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.
Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
