This patch cleans up some locking & error handling in the ppc vdso and
moves the vdso base pointer from the thread struct to the mm context
where it more logically belongs. It brings the powerpc implementation
closer to Ingo's new x86 one and also adds an arch_vma_name() function
allowing to print [vsdo] in /proc/<pid>/maps if Ingo's x86 vdso patch is
also applied.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I have tested PPC_PTRACE_GETREGS and PPC_PTRACE_SETREGS on umview.
I do not understand why historically these tags has been defined as
PPC_PTRACE_GETREGS and PPC_PTRACE_SETREGS instead of simply
PTRACE_[GS]ETREGS. The other "originality" is that the address must be
put into the "addr" field instead of the "data" field as stated in the
manual.
Signed-off-by: renzo davoli <renzo@cs.unibo.it>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Treat R14000 like R10000.
[MIPS] Remove EXPERIMENTAL from PAGE_SIZE_16KB
[MIPS] Update/Fix instruction definitions
[MIPS] DSP and MDMX share the same config flag bit.
[MIPS] Fix deadlock on MP with cache aliases.
[MIPS] Use generic STABS_DEBUG macro.
[MIPS] Create consistency in "system type" selection.
[MIPS] Use generic DWARF_DEBUG
[MIPS] Fix kgdb exception handler from user mode.
[MIPS] Update struct sigcontext member names
[MIPS] Update/fix futex assembly
[MIPS] Remove support for sysmips(2) SETNAME and MIPS_RDNVRAM operations.
[MIPS] Fix detection and handling of the 74K processor.
[MIPS] Add missing 34K processor IDs
[MIPS] Fix marking buddy of pte global for MIPS32 w/36-bit physical address
[MIPS] AU1xxx mips_timer_interrupt() fixes
[MIPS] Fix typo
A proper fix would involve introducing the notion of shared caches but
at this stage of 2.6.17 that's going to be too intrusive and not needed
for current hardware; aside I think some discussion will be needed.
So for now on the affected SMP configurations which happen to suffer from
cache aliases we make use of the fact that a single cache will be shared
by all processors. This solves the deadlock issue and will improve
performance by getting rid of the smp_call_function overhead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "system type" Kconfig options on MIPS are not consistent. For
some platforms, only the name is listed while other entries are
prepended with "Support for". Remove this as it doesn't make sense
when describing the "system type".
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging a kernel compiled by gcc 4.1 with gdb 6.4, gdb could
not show filename, linenumber, etc. It seems fixed if I used generic
DWARF_DEBUG macro. Although gcc 3.x seems work without this change,
it would be better to use the generic macro unless there were
something MIPS specific.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename the 64-bit sc_hi and sc_lo arrays to use the same names
as the 32-bit struct sigcontext (sc_mdhi, sc_hi1, et cetera).
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
SETNAME only had a minor defect but probably never had a user and
MIPS_RDNVRAM was unimplemented anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing exciting; Linux just didn't know it yet so this is most adding
a value to a case statement.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
common/au1000/irq.c was missing a mips_timer_interrupt() prototype,
whereas in common/au1000/time.c the actual mips_timer_interrupt()
implementation was missing an irq_exit() invocation, causing a
preempt_count() leak.
Signed-off-by: Herbert Valerio Riedel <hvr@hvrlab.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation
defined" and it must be set to zero on Intel XScale CPUs or the cache does
not behave properly. Found by Mike Rapoport while debugging a flash issue
on the PXA255:
http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prevent calling of some platform functions on the clock chips of the eMac
as it seems to cause it to lockup at boot. For now, add a quirk to prevent
that from happening. Later, I might find out what's wrong and fix it but
that doesn't seem to be important as the machine appear to work fine
without running those. It's possible that Darwin doesn't run them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nathan Pilatzke <nathanpilatzke@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We don't enable the BTB on the ixp2350 as that can cause weird
crashes (erratum #42.) However, some bootloaders enable the BTB,
which means that we have to disable the BTB explicitly.
Found thanks to Tom Rini.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 5491d0f3e2.
As per Andi:
"After some discussion with people who have the affected system it
seems best to revert for 2.6.17. It broke a common BIOS workaround
and PCI-X still doesn't work. Alternative is for people to change
the BIOS which seems to be better right now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.
This caused problems for UML and some other special programs doing
syscall interception.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Robert Hentosh <robert_hentosh@dell.com>
Actually, we just stumbled on a different bug found in find_e820_area() in
e820.c. The following code does not handle the edge condition correctly:
while (bad_addr(&addr, size) && addr+size < ei->addr + ei->size)
;
last = addr + size;
if ( last > ei->addr + ei->size )
continue;
The second statement in the while loop needs to be a <= b so that it is the
logical negavite of the if (a > b) outside it. It needs to read:
while (bad_addr(&addr, size) && addr+size <= ei->addr + ei->size)
;
In the case that failed bad_addr was returning an address that is exactly size
bellow the end of the e820 range.
AK: Again together with the earlier avoid edma fix this fixes
boot on a Dell PE6850/16GB
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Daniel Yeisley <dan.yeisley@unisys.com>
It is possible to boot a Unisys ES7000 with CPUs from multiple cells, and not
also include the memory from those cells. This can create a scenario where
node 0 has cpus, but no associated memory. The system will boot fine in a
configuration where node 0 has memory, but nodes 2 and 3 do not.
[AK: I rechecked the code and generic code seems to indeed handle that already.
Dan's original patch had a change for mm/slab.c that seems to be already in now.]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Jan Beulich" <jbeulich@novell.com>
The PM timer code updates vxtime.last_tsc, but this update was done
incorrectly in two ways:
- offset_delay being in microseconds requires multiplying with cpu_mhz
rather than cpu_khz
- the multiplication of offset_delay and cpu_khz (both being 32-bit
values) on most current CPUs would overflow (observed value of the
delay was approximately 4000us, yielding an overflow for frequencies
starting a little above 1GHz)
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Jan Beulich" <jbeulich@novell.com>
When using apic= on the kernel command line, this had no effect for machines
matched by either the ACPI MADT or the MPS OEM table scan. However, when such
option is specified, it should also take effect for this set of systems.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Complaining about the IOMMU not compiled in doesn't make sense
here because it is clearly compiled in.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia32_setup_arg_pages would ignore the passed in random stack top
and use its own static value.
Now it uses the 8bit of randomness native i386 would use too.
This indirectly fixes mmap randomization for 32bit processes too,
which depends on the stack randomization.
Should also give slightly better virtual cache colouring and
possibly better performance with HyperThreading.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A typo crept in with commit ea1e847cc2
which defined TI_LOCAL_FLAGS to be the offset of the `flags' field
of struct thread_info, rather than the `local_flags' field. This
fixes it. The typo was pointed out by Guennadi Liakhovetski.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: fix RTC/NVRAM accesses on Maple
[PATCH] ppc32 CPM_UART: various fixes for pq2 uart users
[PATCH] powerpc: linuxppc64.org no more
For a very long time, echoing 'standby' or 'mem' into /sys/power/state has
killed the machine on powerpc. This patch fixes that.
This patch adds the .valid callback to pm_ops on PowerMac so that only the
suspend to disk state can be entered. Note that just returning 0 would
suffice since the upper layers don't pass PM_SUSPEND_DISK down, but we
handle it there regardless just in case that changes.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Due to a firmware device tree bug, RTC and NVRAM accesses (including
halt/reboot) on Maple have been broken since January, when an untested
build fix went in. This code patches the device tree in Linux.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes various odd things that missed update together with cpm_uart
platform_device move. Unified resources names, restructurisation, etc.
Also, addressed issue with recent phys/virt translation rework. Being
cache-coherent, CPM2's do alloc_bootmem() for the console stuff, and it was
used to treat console buffer descriptor mapping 1:1 (as in CPM1 case),
which is definitely wrong.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add missing parentheses for type cast to u64.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There already exists a big endian safe bitops implementation in
lib/find_next_bit.c. The code in it is 90%+ common with the powerpc
specific version, so the powerpc version is redundant. This patch
makes the necessary changes to use the generic bitops in powerpc, and
removes the powerpc specific version.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Consolidate the vio device node creation. Make some parameters const.
Make a few more things __initdata. Get the device_type strings out of
the device tree blob.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This actually simplies things as we just figure out how much space we
used at the end and adjust klimit then.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
First we capture all the strings from dt.c statically by noting that gcc
puts them in a special section of their own. Idea from Michael Ellerman.
Then we move the flattened device tree to klimit.
Still to come, making the values blob grow as needed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the PCI class code to choose a name for the PCI device nodes and
to guess a device_type. Failing that, base the name on the vendor and
device ids as specified in the spec.
Mark just about everything __init{data}.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only scan the host bridges and then use the existing pci_devs_phb_init()
routine.
Also fix typo in setup of reg property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As we now store enough information in the device_node.
Also the Flags field was not used either, do remove that.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As we now store enough information in the device_node to allocate the
irq number in pcibios_final_fixup.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can now scan the list of device nodes instead. This also allows us
to remove the Device_list member of struct pci_dn.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the probing of PCI devices to setup.c and put them all into the
flattened device tree. The later probing is now done by traversing the
device tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This function was removed during iSeries cleanup but will prove useful
in the following patches.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove some unused counters.
No need to allocate iomm_table and iobar_table, which means that
iomm_table_initialize is not longer needed.
Use kzalloc where sensible.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
