In case we have a pending completion, for example due to a problem with
the input clock which got corrected after we timed out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We get called once per DAPM context but only need to run once. When DAPM
was serialized this was a series of noops but now it can run in parallel
we need to take proper care.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
There's no need for separate widgets for the enables (as the map already
shows).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Make AIFCLK supply the record paths otherwise record will not work unless
there is a simultaneous playback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Fix "error: too few arguments to function 'ams_delta_set_bias_level'"
build errors in ams-delta.c that were introduced after commit d4c6005 ("ASoC:
Add context parameter to card DAPM callbacks") by adding dapm context
to ams_delta_set_bias_level calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ASoC core tries to not enforce symmetric rates when
two streams open simultaneously. It does so by checking
rtd->rate being zero. This works exactly once after booting
because it is not set to zero again when the streams close.
Fix this by setting rtd->rate when no active stream is left.
[This leads to lots of warnings about not enforcing the symmetry in some
situations as there's a race in the userspace API where we know we've
got two applications but don't know what rates they want to set.
-- broonie ]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
asoc cache layer can't support this kind of spi registers well.
remove cache support and read/write registers directly
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[This will be used by the ad193x driver to fix the fact that the
original author of the driver put a bodge for their particular chip into
a the generic ASoC register I/O abstraction layer which looked like an
obvious bug which ended up getting fixed in 3.0. Sadly there were no
comments documenting what was going on. A minimally invasive correction
to the driver is to remove the register cache support and go direct to
the hardware all the time so we're adding a new feature -- broonie]
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
system clock is 24.576MHz instead of 12.288MHz
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dac word len value should left shift before setting
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
fix dac word len mask and adc tdm fmt shift value
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
request_any_context_irq() returns a negative value on failure.
On success, it returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.orG
Add linux/types.h to fix this compilation error:
In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:18,
from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add linux/types.h to fix this compilation error:
In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:18,
from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the clocking registers are not overriden some of the registers are
not writable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
sound/soc/codecs/wm8750.c:784:2: warning: missing braces around initializer
sound/soc/codecs/wm8750.c:784:2: warning: (near initialization for ‘wm8750_spi_ids[2].name’)
It's because struct spi_device_id.name is a char array, not a pointer,
while the driver initializes explicitly with 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My gmail account got disabled and I'm not going to reopen it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I2S in Exynos4 and S5PC110(S5PV210) has a internal dma.
It can be used low power audio mode and 2nd channel transfer.
This patch can support idma.
[Reapplied after dependencies propagated through in 3.1-rc1. --broonie]
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This error would have no effect on current silicon revisions, the fall
through case has the same behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
As we had no id_table only the driver name would be matched against
meaning that WM8987 devices wouldn't be bound.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The I2C address is misformatted and would never match.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Without this, request_irq on subsequent device initialization fails, and
the codec cannot be used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two issues were preventing module snd-soc-tegra-wm8903.ko from being
removed and re-inserted:
a) The speaker-enable GPIO is hosted by the WM8903 chip. This GPIO must
be freed before snd_soc_unregister_card() is called, because that
triggers wm8903.c:wm8903_remove(), which calls gpiochip_remove(), which
then fails if any of the GPIOs are in use. To solve this, free all GPIOs
first, so the code doesn't care where they come from.
b) We need to call snd_soc_jack_free_gpios() to match the call to
snd_soc_jack_add_gpios() during initialization. Without this, the
call to snd_soc_jack_add_gpios() fails during any subsequent modprobe
and initialization, since the GPIO and IRQ are already registered. In
turn, this causes the headphone state not to be monitored, so the
headphone is assumed not to be plugged in, and the audio path to it is
never enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all PCM devices have all sub-streams. Specifically, the SPDIF driver
only supports playback and hence has no capture substream. Check whether
a substream exists before dereferencing it, when de-allocating DMA
buffers in tegra_pcm_deallocate_dma_buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This closes the small race between a status being read in response to an
interrupt and clearing the interrupt, meaning that if the status changes
between those periods we might not get a reassertion of the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Commit d006199e72a9 ("serial: sh-sci: Regtype probing doesn't need to be
fatal.") made sci_init_single() return when sci_probe_regmap() succeeds,
although it should return when sci_probe_regmap() fails. This causes
systems using the serial sh-sci driver to crash during boot.
Fix the problem by using the right return condition.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic library code already exports the generic function, this was
left-over from the ARM-specific version that just got removed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 1eb19a12bd ("lib/sha1: use the git implementation of
SHA-1"), the ARM SHA1 routines no longer work. The reason? They
depended on the larger 320-byte workspace, and now the sha1 workspace is
just 16 words (64 bytes). So the assembly version would overwrite the
stack randomly.
The optimized asm version is also probably slower than the new improved
C version, so there's no reason to keep it around. At least that was
the case in git, where what appears to be the same assembly language
version was removed two years ago because the optimized C BLK_SHA1 code
was faster.
Reported-and-tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
task->cred is declared as __rcu, and access to other tasks' ->cred is,
indeed, protected. Access to current->cred does not need rcu_dereference()
at all, since only the task itself can change its ->cred. sparse, of
course, has no way of knowing that...
Add force-cast in current_cred(), make current_fsuid() et.al. use it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al points out that the do_follow_link() helper function really is
misnamed - it's about whether we should try to follow a symlink or not,
not about actually doing the following.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit 3567866bf2: "RCUify freeing acls, let check_acl() go ahead in
RCU mode if acl is cached" posix_acl_permission is being called with an
unsupported flag and the permission check fails. This patch fixes the issue.
Signed-off-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
ore: Make ore its own module
exofs: Rename raid engine from exofs/ios.c => ore
exofs: ios: Move to a per inode components & device-table
exofs: Move exofs specific osd operations out of ios.c
exofs: Add offset/length to exofs_get_io_state
exofs: Fix truncate for the raid-groups case
exofs: Small cleanup of exofs_fill_super
exofs: BUG: Avoid sbi realloc
exofs: Remove pnfs-osd private definitions
nfs_xdr: Move nfs4_string definition out of #ifdef CONFIG_NFS_V4
The inode structure layout is largely random, and some of the vfs paths
really do care. The path lookup in particular is already quite D$
intensive, and profiles show that accessing the 'inode->i_op->xyz'
fields is quite costly.
We already optimized the dcache to not unnecessarily load the d_op
structure for members that are often NULL using the DCACHE_OP_xyz bits
in dentry->d_flags, and this does something very similar for the inode
ops that are used during pathname lookup.
It also re-orders the fields so that the fields accessed by 'stat' are
together at the beginning of the inode structure, and roughly in the
order accessed.
The effect of this seems to be in the 1-2% range for an empty kernel
"make -j" run (which is fairly kernel-intensive, mostly in filename
lookup), so it's visible. The numbers are fairly noisy, though, and
likely depend a lot on exact microarchitecture. So there's more tuning
to be done.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gcc tends to generate better code with small integers, including the
DCACHE_xyz flag tests - so move the common ones to be first in the list.
Also just remove the unused DCACHE_INOTIFY_PARENT_WATCHED and
DCACHE_AUTOFS_PENDING values, their users no longer exists in the source
tree.
And add a "unlikely()" to the DCACHE_OP_COMPARE test, since we want the
common case to be a nice straight-line fall-through.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Compute protocol sequence numbers and fragment IDs using MD5.
crypto: Move md5_transform to lib/md5.c
Export everything from ore need exporting. Change Kbuild and Kconfig
to build ore.ko as an independent module. Import ore from exofs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
ORE stands for "Objects Raid Engine"
This patch is a mechanical rename of everything that was in ios.c
and its API declaration to an ore.c and an osd_ore.h header. The ore
engine will later be used by the pnfs objects layout driver.
* File ios.c => ore.c
* Declaration of types and API are moved from exofs.h to a new
osd_ore.h
* All used types are prefixed by ore_ from their exofs_ name.
* Shift includes from exofs.h to osd_ore.h so osd_ore.h is
independent, include it from exofs.h.
Other than a pure rename there are no other changes. Next patch
will move the ore into it's own module and will export the API
to be used by exofs and later the layout driver
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Exofs raid engine was saving on memory space by having a single layout-info,
single pid, and a single device-table, global to the filesystem. Then passing
a credential and object_id info at the io_state level, private for each
inode. It would also devise this contraption of rotating the device table
view for each inode->ino to spread out the device usage.
This is not compatible with the pnfs-objects standard, demanding that
each inode can have it's own layout-info, device-table, and each object
component it's own pid, oid and creds.
So: Bring exofs raid engine to be usable for generic pnfs-objects use by:
* Define an exofs_comp structure that holds obj_id and credential info.
* Break up exofs_layout struct to an exofs_components structure that holds a
possible array of exofs_comp and the array of devices + the size of the
arrays.
* Add a "comps" parameter to get_io_state() that specifies the ids creds
and device array to use for each IO.
This enables to keep the layout global, but the device-table view, creds
and IDs at the inode level. It only adds two 64bit to each inode, since
some of these members already existed in another form.
* ios raid engine now access layout-info and comps-info through the passed
pointers. Everything is pre-prepared by caller for generic access of
these structures and arrays.
At the exofs Level:
* Super block holds an exofs_components struct that holds the device
array, previously in layout. The devices there are in device-table
order. The device-array is twice bigger and repeats the device-table
twice so now each inode's device array can point to a random device
and have a round-robin view of the table, making it compatible to
previous exofs versions.
* Each inode has an exofs_components struct that is initialized at
load time, with it's own view of the device table IDs and creds.
When doing IO this gets passed to the io_state together with the
layout.
While preforming this change. Bugs where found where credentials with the
wrong IDs where used to access the different SB objects (super.c). As well
as some dead code. It was never noticed because the target we use does not
check the credentials.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
ios.c will be moving to an external library, for use by the
objects-layout-driver. Remove from it some exofs specific functions.
Also g_attr_logical_length is used both by inode.c and ios.c
move definition to the later, to keep it independent
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
