replace pcmcia_socket->lock and pcmcia_dev_list_lock by using the
per-socket "ops_mutex", as we do neither need different locks
nor a spinlock here.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As a side effect,
socket_state_t socket;
u_int state;
u_int suspended_state;
are properly protected now.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As a side effect,
io_window_t io[MAX_IO_WIN];
is explicitely protected now.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Protect the pccard_operations callback "set_mem_map" by a new
mutex ops_mutex. This mutex also protects the following values
in struct pcmcia_socket:
pccard_mem_map win[]
pccard_mem_map cis_mem
void __iomem *cis_virt
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This fixes:
drivers/pcmcia/omap_cf.c:74:1: warning: "SZ_2K" redefined
Since
c1191b0 ([ARM] Kirkwood: create a mapping for the Security Accelerator SRAM)
SZ_2K is defined in arch/arm/include/asm/sizes.h.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This fixes:
drivers/pcmcia/at91_cf.c:55:1: warning: "SZ_2K" redefined
Since
c1191b0 ([ARM] Kirkwood: create a mapping for the Security Accelerator SRAM)
SZ_2K is defined in arch/arm/include/asm/sizes.h.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David Vrabel <dvrabel@arcom.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
O2-bridges can do read prefetch and write burst. However, for some combinations
of older bridges and cards, this causes problems, so it is disabled for those
bridges. Now, as some users know their setup works with the speedups enabled, a
new parameter is introduced to the driver. Now, a user can specifically enable
or disable these features, while the default is what we have today: detect the
bridge and decide accordingly. Fixes Bugzilla entry 15014.
Simplify and unify the printouts, fix a whitespace issue while we are here.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: frodone@gmail.com
[linux@dominikbrodowski.net: whitespace fixes]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The struct file 'private_data' member is a void *, the cast is not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
With CONFIG_PCMCIA=m and CONFIG_YENTA=y, we get
drivers/built-in.o: In function `yenta_probe':
yenta_socket.c:(.devinit.text+0x1e582): undefined reference to
`pccard_nonstatic_ops'
This is because
select PCCARD_NONSTATIC if PCMCIA
sets PCCARD_NONSTATIC = min(YENTA, PCMCIA). Change it to 'if PCMCIA!=n'
to remove the upper limit.
[linux@dominikbrodowski.net: propagate change to PCMICA_M8XX]
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If only CardBus cards are used, but not PCMCIA cards, we do not need
the extensive resource management functions provided for by
rsrc_nonstatic.c (~240K).
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move rsrc_mgr indirections only used by the pcmcia module to the
pcmcia module.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As PCMCIA is the only real user of CIS access functions, include
cistpl.c in the PCMCIA module, not in the PCMCIA & CardBus core
module.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The socket driver m8xx_pcmcia.c uses a static memory assignment,
but io_offset is set to 0. Therefore, it seems proper to use the
iodyn resource manager for this driver, as was previously the
case (before commit 80128ff79d).
CC: Vitaly Bordug <vitb@kernel.crashing.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Olof Johansson <olof@lixom.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
m32r_cfc sets the socket capabilities to SS_CAP_STATIC_MAP and
also sets io_offset != 0. This means no calls to
&pccard_nonstatic_ops went through. Therfore, replace it with
&pccard_static_ops which is exactly for this case.
CC: Mamoru Sakugawa <sakugawa@linux-m32r.org>
CC: Hirokazu Takata <takata@linux-m32r.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove rsrc_mgr indirections only used by pcmcia_resource.c
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As release_resoure_db() used to be called only from one place, and
it's a two-line function, remove it.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Do not lock the socket driver module on card insert, as
the PCMCIA core can handle a socket module removal, at least
if we add a call to socket_remove() on pccardd()'s shutdown.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Do not lock the socket driver module in pcmcia_get_socket(), as
the PCMCIA core can handle a socket module removal: In
pcmcia_unregister_socket(), we explicitely wait for the last
put_device() to succeed.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add a lot of documentation to the rsrc_nonstatic io memory probe
functions. Also, add a first memory probe call -- just checking
whether request_resource() succeeds -- upon adding of resources.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As ds.c is the only real user of CIS access functions, call the
cleanup functions from ds.c, too.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
At least no in-kernel CardBus-capable PCI driver makes use of the CIS
access functions. Therefore, it seems sensible to remove this unused
code, and cleanup cardbus.c a lot.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
During a suspend/resume cycle, an user may change the card in the
PCMCIA/CardBus slot. The pcmcia_core can at least look at the
socket state to check whether it is the same.
For PCMCIA devices, move the detection and handling of such a
change to ds.c.
For CardBus devices, the PCI hotplug interface doesn't offer a "rescan"
facility which also _removes_ devices no longer to be found behind a
bridge. Therefore, remove and re-add all devices unconditionally.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cleanup pccard_validate_cis() and make it return an error code on
all failures, not merely on some failures.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In pccard_validate_cis(), validate the card CIS, not the CIS cache.
Also, destroy the CIS cache if pccard_validate_cis fails.
Furthermore, do not remove the fake CIS in destroy_cis_cache() but
do so explicitely in the code paths where it makes sense.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Do not release any iomem resources already in use.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Komuro pointed out correctly that I missed one IRQ_FIRST_SHARED
parameter in smc91c92_cs.c, and that another line could be writter
more beautifully.
CC: netdev@vger.kernel.org
CC: Komuro <komurojun-mbn@nifty.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In runtime_resume(), do not throw away the return value of
pcmcia_dev_resume(), for we can use it (at least) in
pcmcia_store_pm_state(). This also fixes the pointless assignment
previosly seen there, as noted by Dan Carpenter.
CC: Dan Carpenter <error27@gmail.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'for-linus/samsung' of git://git.fluff.org/bjdooks/linux:
ARM: MINI2440: Fixup __initdata usage
ARM: MINI2440: Fix crash on boot due to improper __initdata qualifier
ARM: SMDK6410: Specify no GPIO for B_PWR_5V regulator
ARM: S3C: NAND: Check the existence of nr_map before copying
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sentelic - fix left/right horizontal scroll mapping
Input: pmouse - move Sentelic probe down the list
Input: add compat support for sysfs and /proc capabilities output
Input: i8042 - add Dritek quirk for Acer Aspire 5610.
Input: xbox - do not use GFP_KERNEL under spinlock
Input: psmouse - fix Synaptics detection when protocol is disabled
Input: bcm5974 - report ABS_MT events
Input: davinci_keyscan - add device_enable method to platform data
Input: evdev - be less aggressive about sending SIGIO notifies
Input: atkbd - fix canceling event_work in disconnect
Input: serio - fix potential deadlock when unbinding drivers
Input: gf2k - fix &&/|| confusion in gf2k_connect()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: cpumask_of_node() should handle -1 as a node
alpha: add myself as a maintainer, and drop mention of 2.4
inotify will WARN() if it finds that the idr and the fsnotify internals
somehow got out of sync. It was only supposed to do this once but due
to this stupid bug it would warn every single time a problem was
detected.
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 7e790dd5fc ("inotify: fix
error paths in inotify_update_watch") inotify changed the manor in which
it gave watch descriptors back to userspace. Previous to this commit
inotify acted like the following:
inotify_add_watch(X, Y, Z) = 1
inotify_rm_watch(X, 1);
inotify_add_watch(X, Y, Z) = 2
but after this patch inotify would return watch descriptors like so:
inotify_add_watch(X, Y, Z) = 1
inotify_rm_watch(X, 1);
inotify_add_watch(X, Y, Z) = 1
which I saw as equivalent to opening an fd where
open(file) = 1;
close(1);
open(file) = 1;
seemed perfectly reasonable. The issue is that quite a bit of userspace
apparently relies on the behavior in which watch descriptors will not be
quickly reused. KDE relies on it, I know some selinux packages rely on
it, and I have heard complaints from other random sources such as debian
bug 558981.
Although the man page implies what we do is ok, we broke userspace so
this patch almost reverts us to the old behavior. It is still slightly
racey and I have patches that would fix that, but they are rather large
and this will fix it for all real world cases. The race is as follows:
- task1 creates a watch and blocks in idr_new_watch() before it updates
the hint.
- task2 creates a watch and updates the hint.
- task1 updates the hint with it's older wd
- task removes the watch created by task2
- task adds a new watch and will reuse the wd originally given to task2
it requires moving some locking around the hint (last_wd) but this should
solve it for the real world and be -stable safe.
As a side effect this patch papers over a bug in the lib/idr code which
is causing a large number WARN's to pop on people's system and many
reports in kerneloops.org. I'm working on the root cause of that idr
bug seperately but this should make inotify immune to that issue.
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a missing iterator variable thus fixing the conditional of the
for-loop in amd64_get_scrub_rate().
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Remove some of the __initdata tags which are currently inappropriate for
platform_device and some of the platform data. These can be returned once
support for copying platform devices and data is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch fix mini2440 crash on boot due to improper __initdata
qualifier on mini2440_led1_pdata.
Signed-off-by: Uri Yosef <uri.yosef@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the fixed voltage regulator grew support for GPIO based
enables and GPIO 0 is valid on some systems we need to specify
that there is no valid GPIO enable control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The sh-sci driver used the wrong fifosize for PORT_SCIFA and PORT_SCIF
ports. If an incorrect size is used, the serial core will enforce an
early shutdown on the port, especially with baudrates < 9600.
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the lis3lv02d motion sensor connected via
i2c on the Ecovec board. Tested with evtest.
Signed-off-by: NISHIMOTO Hiroki <nishimoto.hiroki@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
CC: linux-alpha@vger.kernel.org
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
