CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ePAPR v1.1 requires the spin table to be in cached memory. So we need
to change the call argument of ioremap to enable cache and coherence.
We also flush the cache after writing to spin table to keep it compatible
with previous cache-inhibit spin table. Flushing before and after
accessing spin table is recommended by ePAPR.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are many cases that Semiconductor is misspelled. The patch
fix these typos.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rename the prom_*_property routines of the generic OF code to of_*_property.
This brings them in line with the naming used by the rest of the OF code.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
We unified the Freescale pci/pcie initialization by changing the fsl_pci
to a platform driver. In previous PCI code architecture the initialization
routine is called at board_setup_arch stage. Now the initialization is done
in probe function which is architectural better. Also It's convenient for
adding PM support for PCI controller in later patch.
Now we registered pci controllers as platform devices. So we combine two
initialization code as one platform driver.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the dependency on PCI initialization for SWIOTLB initialization.
So that PCI can be initialized at proper time.
SWIOTLB is partly determined by PCI inbound/outbound map which is assigned
in PCI initialization. But swiotlb_init() should be done at the stage of
mem_init() which is much earlier than PCI initialization. So we reserve the
memory for SWIOTLB first and free it if not necessary.
All boards are converted to fit this change.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support to disable and re-enable individual cores at runtime on
MPC85xx/QorIQ SMP machines. Currently support e500v1/e500v2 core.
MPC85xx machines use ePAPR spin-table in boot page for CPU kick-off. This
patch uses the boot page from bootloader to boot core at runtime. It
supports 32-bit and 36-bit physical address.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Do hardware timebase sync. Firstly, stop all timebases, and transfer the
timebase value of the boot core to the other core. Finally, start all
timebases.
Only apply to dual-core chips, such as MPC8572, P2020, etc.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale / iVeia P1022RDK reference board is a small-factor board
with a Freescale P1022 SOC. It includes:
1) 512 MB 64-bit DDR3-800 (max) memory
2) 8MB SPI serial flash memory for boot loader
3) Bootable 4-bit SD/MMC port
4) Two 10/100/1000 Ethernet connectors
5) One SATA port
6) Two USB ports
7) One PCIe x4 slot
8) DVI video connector
9) Audio input and output jacks, powered by a Wolfson WM8960 codec.
Unlike the P1022DS, the P1022RDK does not have any localbus devices,
presumably because of the localbus / DIU multiplexing restriction of
the P1022 SOC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the Freescale P5040DS Reference Board ("Superhydra"), which
is similar to the P5020DS. Features of the P5040 are listed below, but
not all of these features (e.g. DPAA networking) are currently supported.
Four P5040 single-threaded e5500 cores built
Up to 2.4 GHz with 64-bit ISA support
Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support Up to 1600MT/s
Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
Packet parsing, classification, and distribution (FMAN)
Queue management for scheduling, packet sequencing and
congestion management (QMAN)
Hardware buffer management for buffer allocation and
de-allocation (BMAN)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps SerDes
20 lanes at up to 5 Gbps
Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
Two 10 Gbps Ethernet MACs
Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Two I2C controllers
Four UARTs
Integrated flash controller supporting NAND and NOR flash
DMA
Dual four channel
Support for hardware virtualization and partitioning enforcement
Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NAND flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NAND flash, need to be disabled.
This patch is similar to "powerpc/85xx: p1022ds: disable the NOR flash node
if video is enabled", except that it disables the NAND flash node instead.
This PIXIS node needs to remain enabled because it is used by platform code
to switch into indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
This gives the kernel a paravirtualized machine to target, without
requiring both sides to pretend to be targeting a specific board
that likely has little to do with the host in KVM scenarios. This
avoids the need to add new boards to QEMU just to be able to
run KVM on new CPUs.
As this is the first platform that can run with either e500v2 or
e500mc, CONFIG_PPC_E500MC is now a legitimately user configurable
option, so add a help text.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Similar to how the primary PCI bridge is identified by looking
for an isa subnode, we determine whether to apply uli exclusions
by looking for a uli subnode.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
prom_update_property() currently fails if the property doesn't
actually exist yet which isn't what we want. Change to add-or-update
instead of update-only, then we can remove a lot duplicated lines.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte
shared L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel
Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
UP/DL Channel processing, and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
Inversion operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
with ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network
acceleration including IEEE 1588. v2 hardware support and
virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single
port) and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD
support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
BSC9131RDB Overview
----------------------
BSC9131 SoC
1Gbyte DDR3 (on board DDR)
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
USB-ULPI
eTSEC1: Connected to RGMII PHY
eTSEC2: Connected to RGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 96cc017c5b.
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reference board dates back to 2004, and is largely a legacy
EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.
Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1024rdb has the similar feature as the p1020rdb. Therefore, p1024rdb use
the same platform file as the p1/p2 rdb board.
Overview of P2020RDB platform
- DDR3 1G
- NOR flash 16M
- 3 Ethernet interfaces
- NAND Flash 32M
- SPI EEPROM 16M
- SD/MMC
- 2 USB ports
- 4 TDM ports
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
memblock_end_of_DRAM() returns end_address + 1, not end address.
While some code assumes that it returns end address.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The fixups are executed once the pci-device is found which is during
boot process so __init seems fine as long as the platform does not
support hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 46d026ac ("powerpc/85xx: consolidate of_platform_bus_probe calls")
replaced platform-specific of_device_id tables with a single function
that probes the most of the busses in 85xx device trees. If a specific
platform needed additional busses probed, then it could call
of_platform_bus_probe() again. Typically, the additional platform-specific
busses are children of existing busses that have already been probed.
of_platform_bus_probe() does not handle those child busses automatically.
Unfortunately, this doesn't actually work. The second (platform-specific)
call to of_platform_bus_probe() never finds any of the busses it's asked
to find.
To remedy this, the platform-specific of_device_id tables are eliminated,
and their entries are merged into mpc85xx_common_ids[], so that all busses
are probed at once.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the check for CONFIG_PPC_85xx and CONFIG_PPC_86xx from fsl_guts.h.
The check was originally intended to allow the same header file to
be used on 85xx and 86xx systems, even though the Global Utilities
register could be different. It turns out that they're not actually
different, and so the check is not necessary. In addition, neither
macro is defined for 64-bit e5500 kernels, so that causes a build
break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Disintegrate asm/system.h for PowerPC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: linuxppc-dev@lists.ozlabs.org
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
Remove FPGA(CADMUS) macros in code. Move it to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a PCI bridge(Tsi310) between the MPC8548 and a VIA
southbridge chip.
The bootloader sets the PCI bridge to open a window from 0x0000
to 0x1fff on the PCI I/O space. But the kernel can't set the I/O
resource. In the routine pci_read_bridge_io(), if the base which
is read from PCI_IO_BASE is equal to zero, the routine don't set
the I/O resource of the child bus.
To allow the legacy I/O space on the VIA southbridge to be accessed,
use the fixup to fix the PCI I/O space of the PCI bridge.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc85xx_rdb and mpc85xx_mds have commom define of signal multiplex for qe, so
they need to go in common header, the patch abstract them to fsl_guts.h
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the "select PHYS_64BIT" from the Kconfig entry for the P1022DS,
so that large physical address support is a selectable option for non-CoreNet
reference boards.
The option is enabled in mpc85xx_[smp_]defconfig so that the default is
unchanged. However, now it can be deselected.
The P1022DS had this option defined because the default device tree for
this board uses 36-bit addresses. This had the side-effect of forcing
this option on for all boards that use mpc85xx_[smp_]defconfig. Some
users may want to disable this feature to create an optimized configuration
for boards with <= 2GB of RAM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl_85xx_l2ctlr.o and fsl_85xx_cache_sram.o are built only
if CONFIG_FSL_85XX_CACHE_SRAM is defined. The driver that
qualifies and wants to make use of the CACHE SRAM's exported
API (i.e. a freescale net driver) should (be able to) select
this config option.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When the P1022's DIU video controller is active, the pixis must be accessed
in "indirect" mode, which uses localbus chip select addresses.
Switching between the DVI and LVDS monitor ports is handled by the pixis,
so that switching needs to be done via indirect mode.
This has the side-effect of no longer requiring U-Boot to enable the DIU.
Now Linux can enable the DIU all by itself.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020utm-pc has the similar feature as the p1020rdb.
Therefore, p1020utm-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020UTM-PC platform:
- DDR3 1GB
- NOR flash 32MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY Atheros AR8021)
- eTSEC2 (SGMII PHY Vitesse VSC8221)
- eTSEC3 (RGMII PHY Atheros AR8021)
- SDHC
- 2 USB ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020mbg-pc has the similar feature as the p1020rdb.
Therefore, p1020mbg-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020MBG-PC platform:
- DDR3 2GB
- NOR flash 64MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch
- eTSEC2 (SGMII PHY)
- eTSEC3 (RGMII PHY)
- SDHC
- 2 USB ports
- 4 TDM ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NOR flash, need to be disabled.
This also means that the localbus is not a 'simple-bus' any more, so remove
that string from the compatible node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2020RDB-PC Board shares the same design(PCB) as P102x RDB style platforms.
The difference between this platform and the already existing P2020RDB
is mainly with respect to DDR. The P2020RDB-PC has a DDR3 memory.
The P2020RDB-PC also has a CPLD device connected to local bus.
The main differences from the P102x RDB-PC is 64-bit DDR and SYSCLK of
100Mhz.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
