Use simple macros to clean up the printks.
(This patch is reverted by the 14th patch to follow.)
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for jumbo ethernet frames.
(This patch depends on patch 7 to follow.)
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid memory copy on writes.
(This patch depends on fixes in patch 9 to follow.)
Although skb->len should not be set when working with linear skbuffs,
the skb->tail pointer maintained by skb_put/skb_trim is not relevant
to what happens when the skb_fill_page_desc function is called. This
issue was raised without comment in linux-kernel and netdev earlier
this month:
http://thread.gmane.org/gmane.linux.kernel/446474/http://thread.gmane.org/gmane.linux.network/45444/
So until there is something analogous to skb_put that works for
zero-copy write skbuffs, we will do what the other callers of
skb_fill_page_desc are doing.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The NARGS enum is left over from older code versions.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the copyright year to 2006.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This message doesn't help users because the circumstance isn't problematic.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a typo to make kernel compilable when floppy driver
for Sparc is build.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds profiling support to the sparc architecture. It is a
copy of the sparc64 implementation.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be calling kernel_execve() directly and this
causes module build failures because kernel_execve() is not
exported to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
For Hummingbird PCI controllers, we should create the root
PCI memory space resource as the full 4GB area, and then
allocate the IOMMU DMA translation window out of there.
The old code just assumed that the IOMMU DMA translation base
to the top of the 4GB area was unusable. This is not true on
many systems such as SB100 and SB150, where the IOMMU DMA
translation window sits at 0xc0000000->0xdfffffff.
So what would happen is that any device mapped by the firmware
at the top section 0xe0000000->0xffffffff would get remapped
by Linux somewhere else leading to all kinds of problems and
boot failures.
While we're here, report more cases of OBP resource assignment
conflicts. The only truly valid ones are ROM resource conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
Unused, but still allow the '-s' boot option to be passed
down to init.
Based upon patches by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
It would fail the compile due to the newly added error checking testing
a bad macro for a "return value" unless USB_GADGET_DEBUG_FILES was
enabled.
Pointed out by Stephen Hemminger.
Acked-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
USB: Add device id for Sierra Wireless MC8755
USB: cleanup sierra wireless driver a bit
USB: Sierra Wireless driver update
USB: ftdi_sio whitespace fixes
USB-SERIAL:cp2101 Add new device ID
USB/gadget/net2280: handle sysfs errors
usbtouchscreen: fix data reading for ITM touchscreens
UEAGLE: fix ueagle-atm Oops
USB: xpad: dance pad support
USB: input: extract() and implement() are bit field manipulation routines
USB: Memory leak in drivers/usb/serial/airprime.c
USB Storage: unusual_devs.h entry for Sony Ericsson P990i
USB: fix usbatm tiny race
USB: unusual_devs entry for Nokia 6234
USB: mos7840.c: fix a check-after-dereference
USB: ftdi-elan.c: remove dead code
USB: Mitsumi USB FDD 061M: UNUSUAL_DEV multilun fix
USB: fix dereference in drivers/usb/misc/adutux.c
USB: add USB serial mos7720 driver
USB: move trancevibrator.c to the proper usb directory
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Use mmiowb after doorbell ring
IB/ipath: Initialize diagpkt file on device init only
RDMA/amso1100: Fix a NULL dereference in error path
RDMA/amso1100: pci_module_init() conversion
Adds the device id used by the UMTS cards in Lenovo X60s notebooks sold
in Europe.
Signed-off-by: Jan Luebbe <jluebbe@lasnet.de>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This saves over 30 lines and fixes a warning from sparse and allows
debugging to work dynamically like all other usb-serial drivers.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The largest feature in this patch is that it adds significant throughput
increase to the Sierra driver and adds support for modem status line
control (e.g. the DTR line). This patch also updates the current sierra.c
driver so that it supports both 3-port Sierra devices and 1-port legacy
devices and removes Sierra's references in other related files (Kconfig and
airprime.c).
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds device ID 0xEA61. This is another factory default ID
used by SILabs.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ITM devices seem to report only garbage when not touched. update usbtouchscreen
to do data reading like itmtouch. also fix wrong mask on pressure bits.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The array of attribute passed to sysfs_create_group() must be
NULL-terminated.
The sysfs entries are created before the start of the modem state machine
to avoid to stop it in case of errors in sysfs creation. Also
{destroy,create}_fs_entries are removed as they do nothing.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for dance pads to the xpad driver. Dance pads require the
d-pad to be mapped to four buttons instead of two axes, so that
combinations of up/down and left/right can be hit simultaneously.
Known dance pads are detected, and there is a module parameter added
to default unknown xpad devices to map the d-pad to buttons if this is
desired. (dpad_to_buttons). Minor modifications were made to port the
changes in the original patch to a newer kernel version.
This patch was originally from Dominic Cerquetti originally written
for kernel 2.6.11.4, with minor modifications (API changes for USB,
spelling fixes to the documentation added in the original patch) made
to apply to the current kernel. I have modified Dominic's original
patch per some suggestions from Dmitry Torokhov. (There was nothing
in the patch format description about multiple From: lines, so I
haven't added myself.)
[akpm@osdl.org: cleanups]
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
extract() and implement() have brain damaged attempts to handle 32-bit wide
"fields".
The problem is the index math in the original code didn't clear all the
relevant bits. (offset >> 5) only compensated for 32-bit index. We need
(offset >> 6) if we want to use 64-bit loads.
But it was also wrong in that it tried to use quasi-aligned loads. Ie
"report" was only incremented in multiples of 4 bytes and then the offset
was masked off for values greater than 4 bytes. The right way is to
pretend "report" points at a byte array. And offset is then only minor
adjustment for < 8 bits of offset. "n" (field width) can then be as big as
24 (assuming 32-bit loads) since "offset" will never be bigger than 7.
If someone needs either function to handle more than 24-bits, please
document why - point at a specification or specific USB hid device - in
comments in the code.
extract/implement() are also an eyesore to read. Please banish whoever
wrote it to read CodingStyle 3 times in a row to a classroom full of 1st
graders armed with rubberbands. Or just flame them. Whatever. Globbing
all the code together on two lines does NOT make it faster and is Just
Wrong.
I've tested this patch on j6000 (dual 750Mhz PA-RISC, 32-bit 2.6.12-rc5).
Kyle McMartin tested on c3000 (up 400Mhz PA-RISC, same kernel). "p2-mate"
(Peter De Schrijver?) tested on sb1250 (dual core Mips, broadcom "swarm"
eval board).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ia64:
drivers/usb/atm/usbatm.c: In function `usbatm_do_heavy_init':
drivers/usb/atm/usbatm.c:1004: warning: implicit declaration of function `get_current'
drivers/usb/atm/usbatm.c:1004: error: invalid type argument of `->'
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as803) adds an unusual_devs entry for the Nokia 6234
mobile phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an obvious check-after-dereference spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in two of the error cases, dev is still NULL,
and we dereference it. Spotted by coverity (cid#1428, 1429)
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for Moschip 7720 USB dual port usb to serial device.
This driver is originally based on the drivers/usb/io_edgeport.c driver.
Cleaned up and forward ported by me.
Cc: VijayaKumar <vijaykumar@aspirecom.net>
Cc: AjayKumar <ajay@aspirecom.net>
Cc: Gurudeva <gurudev@aspirecom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not a input driver, so it doesn't belong in the input directory.
Cc: Sam Hocevar <sam@zoy.org>
Cc: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When working on the mcs7830, I noticed the need for a mutex in its
mdio_read/mdio_write functions. A related problem seems to be present
in the asix driver in the respective functions.
This introduces a mutex in the common usbnet driver and uses it
from the two hardware specific drivers.
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds generic support for the ethtool commands get_settings,
set_settings, get_link and nway_reset to usbnet. These are now
implemented using mii functions when a low-level driver supports
mdio_read/mdio_write and does not override the usbnet ethtool
commands with its own.
Currently, this applies to the asix and the mcs7830 drivers.
I have tested it on mcs7830.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver adds support for the DeLOCK USB ethernet adapter
and potentially others based on the MosChip MCS7830 chip.
It is based on the usbnet and asix drivers as well as the
original device driver provided by MosChip, which in turn
was based on the usbnet driver.
It has been tested successfully on an OHCI, but interestingly
there seems to be a problem with the mcs7830 when connected to
the ICH6/EHCI in my thinkpad: it keeps receiving lots of
broken packets in the RX interrupt. The problem goes away when
I'm using an active USB hub, so I assume it's not related to
the device driver, but rather to the hardware.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds missing class_device_create() error check,
and makes notifier return NOTIFY_BAD.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as800) straightens out the USB endpoint class device
creation routine, fixing a refcount bug in the process.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as799) fixes a nasty refcount error in the USB endpoint class.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as798) adds a workaround to uhci-hcd. At least one Asus
motherboard is wired in such a way that any device attached to a
suspended UHCI controller will prevent the system from entering
suspend-to-RAM by immediately waking it up. The only way around the
problem is to turn the controller off instead of suspending it.
This fixes Bugzilla #6193.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Deleted some unused code that could do bad things on non-x86 platforms.
Also fixed some minor formatting errors.
Thanks to Al Viro for pointing out the sparse errors.
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this implements suspend support for usblp. According to the CUPS people
ENODEV will make CUPS retry the job. Thus it is returned in the runtime
case. My printer survives suspend/resume cycles with it.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The speedtouch modem setup code was reverse engineered many years
ago from a prehistoric windows driver. Less ancient windows drivers,
even those from a few years ago, perform extra initialization steps
which this patch adds to the linux driver. David Woodhouse observed
that this initialization along with the firmware bin/sachu3/zzzlp2.eni
from the driver at
http://www.speedtouch.co.uk/downloads/330/301/UK3012%20Extended.zip
improves line sync speeds by about 20%. He provided the original
patch, which I've modified to use symbolic names (BMaxDSL, ModemMode,
ModemOption) rather than magic numbers. These names may not seem like
much of an improvement (after all, what is "ModemOption" exactly?),
but they do have one big advantage: they are the names used in the
windows registry. I've made them available as module parameters.
Thanks are due to Aurelio Arroyo, who noticed the relationship
between these magic numbers and the entries in Phonebook.ini.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If usbatm_do_heavy_init finishes before usbatm_heavy_init
writes the pid, the disconnect method could shoot down the
wrong process if the pid has been recycled.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
