We no longer write to the channel data structure, so we can make it
const throughout the driver.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination cctl values into the channel structure.
This moves us towards being able to avoid a configuration call each
time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination slave address separately into the channel
structure. This moves us towards being able to avoid a configuration
call each time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This workaround aims to break the deadlock situation
which raises during continuous transfer of data for long
duration over uart with hardware flow control. It is
observed that CTS interrupt cannot be cleared in uart
interrupt register (ICR). Hence further transfer over
uart gets blocked.
It is seen that during such deadlock condition ICR
don't get cleared even on multiple write. This leads
pass_counter to decrease and finally reach zero. This
can be taken as trigger point to run this UART_BT_WA.
Workaround backups the register configuration, does soft
reset of UART using BIT-0 of PRCC_K_SOFTRST_SET/CLEAR
registers and restores the registers.
This patch also provides support for uart init and exit
function calls if present.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support pm_ops in the AMBA bus, required to allow drivers to use runtime pm.
The implementation of AMBA bus pm ops is based on the platform bus
implementation.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the bus level code deals with a const id table, we can also
make the ID table in the amba_driver structure also const.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Export amba_bustype struct so it can be used for things like registering
bus notifiers.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM CLCD PL110 controller in TFT mode provides two output formats
based on whether the controller is in 24bpp mode or not - either 5551
or 888. PL111 augments this with a 444 and 565 modes.
Some implementations provide an external MUX on the PL110 output to
reassign the bits to achieve 565 mode.
Provide a system of capability flags to allow the CLCD driver to work
out what is supported by each panel and board, and therefore which
display formats are permitted.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of matching the entire peripheral ID, match against
just the part number using the amba_xxx() macros.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on a patch from Linus Walleij.
Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface. The changes over Linus' driver are:
- rename txsize_threshold to dmasize_threshold, as this reflects the
purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer. Some DMA controllers
(eg, PL08x) are unable to be configured for scatter DMA and also listen
to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the
final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
its own restrictions on buffer alignment, not the individual DMA engine
users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
causes LBREQ to be asserted for the last seven transfers, rather than
six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
transfer size required to complete the DMA operation.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (63 commits)
ARM: PL08x: cleanup comments
Update CONFIG_MD_RAID6_PQ to CONFIG_RAID6_PQ in drivers/dma/iop-adma.c
ARM: PL08x: fix a warning
Fix dmaengine_submit() return type
dmaengine: at_hdmac: fix race while monitoring channel status
dmaengine: at_hdmac: flags located in first descriptor
dmaengine: at_hdmac: use subsys_initcall instead of module_init
dmaengine: at_hdmac: no need set ACK in new descriptor
dmaengine: at_hdmac: trivial add precision to unmapping comment
dmaengine: at_hdmac: use dma_address to program DMA hardware
pch_dma: support new device ML7213 IOH
ARM: PL08x: prevent dma_set_runtime_config() reconfiguring memcpy channels
ARM: PL08x: allow dma_set_runtime_config() to return errors
ARM: PL08x: fix locking between prepare function and submit function
ARM: PL08x: introduce 'phychan_hold' to hold on to physical channels
ARM: PL08x: put txd's on the pending list in pl08x_tx_submit()
ARM: PL08x: rename 'desc_list' as 'pend_list'
ARM: PL08x: implement unmapping of memcpy buffers
ARM: PL08x: store prep_* flags in async_tx structure
ARM: PL08x: shrink srcbus/dstbus in txd structure
...
Cleanup the formatting of comments, remove some which don't make sense
anymore.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[fix conflict with 96a608a4]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/amba-pl08x.c: In function 'pl08x_start_txd':
drivers/dma/amba-pl08x.c:205: warning: dereferencing 'void *' pointer
We never dereference llis_va aside from assigning it to a struct
pl08x_lli pointer or calculating the address of array element 0.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ST Micro variants has some specific dma burst threshold compensation,
which allows them to make better use of a DMA controller. Add support
to set this up.
Based on a patch from Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DMA engine support for transmit to the PL011 driver. Based on a
patch from Linus Walliej, with the following changes:
- remove RX DMA support. As PL011 doesn't give us receive timeout
interrupts, we only get notified of received data when the RX DMA
has completed. This rather sucks for interactive use of the TTY.
- remove abuse of completions. Completions are supposed to be for
events, not to tell what condition buffers are in. Replace it with
a simple 'queued' bool.
- fix locking - it is only safe to access the circular buffer with the
port lock held.
- only map the DMA buffer when required - if we're ever behind an IOMMU
this helps keep IOMMU usage down, and also ensures that we're legal
when we change the scatterlist entry length.
- fix XON/XOFF sending - we must send XON/XOFF characters out as soon
as possible - waiting for up to 4095 characters in the DMA buffer
to be sent first is not acceptable.
- fix XON/XOFF receive handling - we need to stop DMA when instructed
to by the TTY layer, and restart it again when instructed to. There
is a subtle problem here: we must not completely empty the circular
buffer with DMA, otherwise we will not be notified of XON.
- change the 'enable_dma' flag into a 'using DMA' flag, and track
whether we can use TX DMA by whether the channel pointer is non-NULL.
This gives us more control over whether we use DMA in the driver.
- we don't need to have the TX DMA buffer continually allocated for
each port - instead, allocate it when the port starts up, and free
it when it's shut down. Update the 'using DMA' flag if we get
the buffer, and adjust the TTY FIFO size appropriately.
- if we're going to use PIO to send characters, use the existing IRQ
based functionality rather than reimplementing it. This also ensures
we call uart_write_wakeup() at the appropriate time, otherwise we'll
stall.
- use DMA engine helper functions for type safety.
- fix init when built as a module - we can't have to initcall functions,
so we must settle on one. This means we can eliminate the deferred
DMA initialization.
- there is no need to terminate transfers on a failed prep_slave_sg()
call - nothing has been setup, so nothing needs to be terminated.
This avoids a potential deadlock in the DMA engine code
(tasklet->callback->failed prepare->terminate->tasklet_disable
which then ends up waiting for the tasklet to finish running.)
- Dan says that the submission callback should not return an error:
| dma_submit_error() is something I should have removed after commit
| a0587bcf "ioat1: move descriptor allocation from submit to prep" all
| errors should be notified by prep failing to return a descriptor
| handle. Negative dma_cookie_t values are only returned by the
| dma_async_memcpy* calls which translate a prep failure into -ENOMEM.
So remove the error handling at that point. This also solves the
potential deadlock mentioned in the previous comment.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PL08x driver holds on to the channel lock with interrupts disabled
between the prepare and the subsequent submit API functions. This
means that the locking state when the prepare function returns is
dependent on whether it suceeeds or not.
It did this to ensure that the physical channel wasn't released, and
as it used to add the descriptor onto the pending list at prepare time
rather than submit time.
Now that we have reorganized the code to remove those reasons, we can
now safely release the spinlock at the end of preparation and reacquire
it in our submit function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Introduce 'phychan_hold' to hold on to physical DMA channels while we're
preparing a new descriptor for it. This will be incremented when we
allocate a physical channel and set the MUX registers during the
preparation of the TXD, and will only be decremented when the TXD is
submitted.
This prevents the physical channel being given up before the new TXD
is placed on the queue.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This 'desc_list' is actually a list of pending descriptors, so name
it after its function (pending list) rather than what it contains
(descriptors).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We only need to store the dma address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Platforms need to be able to control which AHB master interface is used,
as each AHB master interface may be asymetric. Allow the interfaces
used for fetching LLIs, memory, and each peripheral to be configured
individually.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Rather than modifying platform data while preparing a transfer, copy
the cctl value into the txd structure and modify the value there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ccfg register is used to configure the channel parameters - the type
and direction of transfer, the flow control signal and IRQ mask enables.
The type and direction of transfer is known in the relevent prep_*
function where a txd is created. The IRQ mask enables are always set,
and the flow control signals are always set when we start processing a
txd according to phychan->signal.
If we store the ccfg value in the txd structure, we can avoid modifying
platform data - and even having it in platform data at all.
So, remove it from platform data too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As we now have all the code accessing the phychan {csrc,cdst,clli,cctl,
ccfg} members in one function, there's no point storing the data into
the struct. Get rid of the struct members. Re-order the register dump
in the dev_dbg() to reflect the order we write the registers to the DMA
device.
The txd {csrc,cdst,clli,cctl} values are duplicates of the lli[0]
values, so there's no point duplicating these either. Program the DMAC
registers directly from the lli[0] values.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use size_t for variables denoting lengths throughout, and use the 'z'
qualifier for printing the value. For safety, add a BUG_ON() in
pl08x_fill_lli_for_desc() to catch the remainder potentially becoming
negative.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid using 'void *' struct fields when the structs are not defined
in linux/amba/pl08x.h - instead, forward declare the struct names, and
use these instead. This ensures we have proper typechecking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The last_issued variable uses an atomic type, which is only
incremented inside a protected region, and then read. Everywhere else
only reads the value, so it isn't using atomic_t correctly, and it
doesn't even need to. Moreover, the DMA engine code provides us with
a variable for this already - chan.cookie. Use chan.cookie instead.
Also, avoid negative dma_cookie_t values - negative returns from
tx_submit() mean failure, yet in reality we always succeed. Restart
from cookie 1, just like other DMA engine drivers do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On some contemporary sub-micron SoCs, peripherals on the chip have
power domain switches, i.e. the voltage to the core may be turned
off to conserve power. In the Ux500 we have this for out PrimeCell
derivates.
This patch makes it possible to specify an (optional) regulator to
handle the voltage domain switch on AMBA PrimeCells, modeled very
similar to how block clocks are handled.
Additional amba_vcore_[enable|disable] calls are supplied to make
it possible introduce optional powering off of the core voltage.
Using this will require code to spool/unspool any core HW state.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Cc: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (48 commits)
DMAENGINE: move COH901318 to arch_initcall
dma: imx-dma: fix signedness bug
dma/timberdale: simplify conditional
ste_dma40: remove channel_type
ste_dma40: remove enum for endianess
ste_dma40: remove TIM_FOR_LINK option
ste_dma40: move mode_opt to separate config
ste_dma40: move channel mode to a separate field
ste_dma40: move priority to separate field
ste_dma40: add variable to indicate valid dma_cfg
async_tx: make async_tx channel switching opt-in
move async raid6 test to lib/Kconfig.debug
dmaengine: Add Freescale i.MX1/21/27 DMA driver
intel_mid_dma: change the slave interface
intel_mid_dma: fix the WARN_ONs
intel_mid_dma: Add sg list support to DMA driver
intel_mid_dma: Allow DMAC2 to share interrupt
intel_mid_dma: Allow IRQ sharing
intel_mid_dma: Add runtime PM support
DMAENGINE: define a dummy filter function for ste_dma40
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
What is the dev pointer doing inside the platform data anyway.
We have another pointer to the actual device at hand, use that.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds spi->mode support for the AMBA pl022 driver and
allows spidev to correctly alter SPI modes. Unused fields used in
the pl022 header file for the pl022_config_chip have been removed.
The ab8500 client driver selects the data transfer size instead
of the platform data.
For platforms that use the amba pl022 driver, the unused fields
in the controller data structure have been removed and the .mode
field in the SPI board info structure is used instead.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This extends the PL022 SSP/SPI driver with generic DMA engine
support using the PrimeCell DMA engine interface. Also fix up the
test code for the U300 platform.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The ST Micro derivates have several extra interesting registers
that we may soon use for something interesting so may just as
well define them in the header.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This make four macros for the PrimeCell ID register available to
drivers that use them witout using the PrimeCell/AMBA bus
abstraction and struct amba_device. It also moves the magic
PrimeCell CID "B105F00D" to the bus.h header file.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This creates a DMAengine driver for the ARM PL080/PL081 PrimeCells
based on the implementation earlier submitted by Peter Pearse.
This is working like a charm for memcpy and slave DMA to the PL011
PrimeCell on the PB11MPCore.
This DMA controller is used in mostly unmodified form in the ARM
RealView and Versatile platforms, in the ST-Ericsson Nomadik, and
in the ST SPEAr platform.
It has been converted to use the header from the Samsung PL080
derivate instead of its own defintions. The Samsungs have a custom
driver in their mach-* folders though, atleast we can share the
register definitions.
Cc: Peter Pearse <peter.pearse@arm.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[GFP_KERNEL to GFP_NOWAIT in pl08x_prep_dma_memcpy]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On some platforms, the GPIO value from the gpio_cd pin doesn't need to
be inverted to get it active high. Add a cd_invert platform data
parameter and change existing platforms using GPIO for CD (only
Realview) to enable it.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the clock enable/disable tracking in the AMBA CLCD driver so
that the driver doesn't try to disable an already disabled clock,
thereby causing the clock (if shared) to become unbalanced.
This resolves a problem with CLCD on LPC32xx ARM platforms.
Reported-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms gate the pclk (APB - the bus - clock) to the peripherals
for power saving, along with the functional clock. When devices are
accessed without pclk enabled, the kernel will oops.
This gives them two options:
1. Leave all clocks on all the time.
2. Attempt to gate pclk along with the functional clock.
(With some hardware, pclk and the functional clock are gated by a single
bit in a register.)
(1) has the disadvantage that it causes increased power usage, which is
bad news for battery operated devices. (2) can lead to kernel oops if
registers are accessed without the functional clock being enabled.
So, introduce the apb_pclk signal in such a way existing drivers don't
need to be updated. Essentially, this means we guarantee that:
1. pclk will be enabled whenever the driver is bound to a device -
from probe() to remove() time.
2. pclk will also be enabled when reading the primecell IDs from the device.
In order to allow drivers to be incrementally updated to achieve greater
power savings, we provide two additional calls to allow drivers to
manage the pclk - amba_pclk_enable()/amba_pclk_disable().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Platforms may have some external power control which need to be
controlled from board specific code. Rename the translate_vdd()
callback to vdd_handler() and pass it the power mode.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implementation of the ST-Ericsson baudrate extension in the PL011
block. In this modified variant it is possible to change the
sampling factor from 16 to 8, and thanks to this we can get higher
baudrates while still using the same peripheral clock.
Also replace the simple division to determine the baud divisor
with DIV_ROUND_CLOSEST() rather than a simple integer division.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the ST-Ericsson version of the PL011 the TX and RX have different
control registers.
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
