Receiving pause frames can block TX queue flushes. Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:
- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
as part of net driver modules. (This also fixes cases where the PTP
subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
drivers but are built separately
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Some interface statistics are computed in such a way that they can
sometimes decrease (and even underflow). Since the computed value
will never be greater than the true value, we fix this by only storing
the computed value when it increases.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
During probe of each port, read and log the part number from VPD.
Remove the Falcon-specific board name lookup.
Initial version by Stuart Hodgson <smhodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Generate a test event on each event queue whenever the interface is
brought up, then after 1 second check that we have either handled a
test event or handled another IRQ for each event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register. These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.
We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.
There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.
The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.
This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Each port has a block of 64-bit SRAM that is divided between buffer
table and descriptor cache regions at initialisation time. Currently
we use a fixed allocation, but it needs to be changed to support
larger numbers of queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
For SR-IOV we will need to send events to event queues that belong to
VFs serviced by other drivers. Change the parameters of
efx_generate_event() to allow this and declare it extern.
While we're at it, remove the existing declaration under the wrong
name efx_nic_generate_event().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The 'page size' for PCIe DMA, i.e. the alignment of boundaries at
which DMA must be broken, is 4KB. Name this value as EFX_PAGE_SIZE
and use it in efx_max_tx_len(). Redefine EFX_BUF_SIZE as
EFX_PAGE_SIZE since its value is also a result of that requirement,
and use it in efx_init_special_buffer().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The SFC9000-family controllers have firmware to manage all board
peripherals including temperature, heat sink continuity and voltage
sensors. The firmware reports sensor alarms, which we log, and
will shut down the board if necessary.
Some users may want to monitor their boards more closely, so add an
hwmon driver that exposes all sensors reported by the firmware. Move
efx_mcdi_sensor_event() into the new file so it can share the array of
sensor labels with the hwmon driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We currently assume that the timer quantum for Siena is 5 us, the same
as for Falcon. This is not correct; timer ticks are generated on a
rota which takes a minimum of 768 cycles (each event delivery or other
timer change will delay it by 3 cycles). The timer quantum should be
6.144 or 3.072 us depending on whether turbo mode is active.
Replace EFX_IRQ_MOD_RESOLUTION with a timer_quantum_ns field in struct
efx_nic, initialised by the efx_nic_type::probe function.
While we're at it, replace EFX_IRQ_MOD_MAX with a timer_period_max
field in struct efx_nic_type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
No NICs need to switch efx_mac_operations at run-time, and the MAC
operations are fairly closely bound to NIC types.
Move efx_mac_operations::reconfigure to efx_nic_type::reconfigure_mac
and efx_mac_operations::check_fault fo efx_nic_type::check_mac_fault.
Change callers to call through efx->type or directly if the NIC type
is known.
Remove efx_mac_operations::update_stats. The implementations for
Falcon used to fetch MAC statistics synchronously and this was used by
efx_register_netdev() to clear statistics after running self-tests.
However, it now only converts statistics that have already been
fetched (and that only for Falcon), and the call from
efx_register_netdev() has no effect.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add a range check, and move the check that RX and TX are consistent
from efx_ethtool_set_coalesce().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.
CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
