Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.
Also change wire4 to be wires, as some newer controllers support
8 data lines.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This will simplify the MMC low-level init, and make it more
flexible to add support for a newer MMC controller in the
following patches.
The patch rearranges platform data and gets rid of slot vs
controller confusion in the old data structures. Also fix
device id numbering in the clock code.
Some code snippets are based on an earlier patch by
Russell King <linux@arm.linux.org.uk>.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds some new pin multiplexing options
for McBSP and McSPI from Arun KS. Also add two more
GPIOs from David Brownell.
Also mark omap24xx_cfg_reg() static.
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
system_rev is meant for board revision, this patch changes
all relevant instances to use the new omap_rev() function
liberating system_rev to be used with ATAG_REVISION as it
has been designed.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At some point omap2 changed the bits for GET_OMAP_CLASS, which
broke 15xx detection on 730 as noticed by Russell King.
This patch fixes omap2 cpu detection to respect the original
GET_OMAP_CLASS, and simplifies the detection for 34xx.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clean up OMAP GPIO request/free functions
- Rename and declare static OMAP specific GPIO request/free functions
- Register them into gpiolib as chip-specific hooks
- Add omap_request_gpio/omap_free_gpio wrappers for existing code not
converted yet to use gpiolib
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
[ dbrownell@users.sourceforge.net: remove needless check_gpio() calls ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More conversion to the standard GPIO interfaces: stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.
Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.
- For the call sites which defined an initial value either
before or after setting the direction, that value was used.
When that value was previously assigned afterwards, this
could eliminate a brief output glitch ... and possibly
change behavior. In a few cases (LCDs) several values
were assigned together ... those were re-arranged to match
the explicit sequence provided.
- Some call sites didn't define such a value; so I chose an
initial "off/reset" value that seemed to default to "off".
In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make OMAP use the new __gpio_to_irq() hook, to make it easier to
support IRQs coming in from off-chip gpio controllers like the
TWL4030/TPS65930 chip used on OMAP3 boads like Beagleboard.org and
the Gumstix Overo.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes a number of sillies, from missing 'const' to using
'return' in void functions, to functions with no arguments not even
'void' and a cast which isn't required.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second clk_deny_idle instance should be clk_allow_idle instead.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On omap24xx, INTCPS_SIR_IRQ_OFFSET bits [6:0] contains the current
active interrupt number.
However, on 34xx INTCPS_SIR_IRQ_OFFSET bits [31:7] also contains the
SPURIOUSIRQFLAG, which gets set if the interrupt sorting information
is invalid.
If the SPURIOUSIRQFLAG bits are not ignored, the interrupt code will
occasionally produce a bunch of confusing errors:
irq -33, desc: c02ddcc8, depth: 0, count: 0, unhandled: 0
->handle_irq(): c006f23c, handle_bad_irq+0x0/0x22c
->chip(): 00000000, 0x0
->action(): 00000000
Fix this by masking out only the ACTIVEIRQ bits. Also fix a
confusing comment.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
Some McBSP irq defines were missing that should have been added
with the earlier McBSP patches.
Add the missing McBSP irqs, and a few other missing irqs as
defined in linux-omap tree. Also add a blank line to separate
irq defines from the irq line calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
This adds minimal board support for the OMAP3430 LDP development platform.
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal Beagle board support. Based on earlier patches
by Syed Mohammed Khasim with some fixes from linux-omap tree.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal omap3430 support based on earlier patches from
Syed Mohammed Khasim. Also merge in omap34xx SRAM support
from Karthik Dasu and use consistent naming for sram init
functions.
Also do following changes that make 34xx support usable:
- Remove unused sram.c functions for 34xx
- Rename IRQ_SIR_IRQ to INTCPS_SIR_IRQ and define it locally
in entry-macro.S
- Update mach-omap2/io.c to support 2420, 2430, and 34xx
- Also merge in 34xx GPMC changes to add fields wr_access and
wr_data_mux_bus from Adrian Hunter
- Remove memory initialization call omap2_init_memory() until
until more generic memory initialization patches are posted.
It's OK to rely on bootloader initialization until then.
Signed-off-by: Syed Mohammed, Khasim <khasim@ti.com>
Signed-off-by: Karthik Dasu<karthik-dp@ti.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on Chandra's earlier patches in linux-omap tree.
Signed-off-by: Chandra Shekhar <x0044955@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on Chandra's earlier patches in linux-omap tree.
Note that omap1_mcbsp_check and omap2_mcbsp_check are no longer
needed as there's now omap_mcbsp_check_valid_id() defined.
Also some functions can now be marked __init.
Signed-off-by: Chandra Shekhar <x0044955@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc updates from linux-omap tree, mostly to update common
device initialization and add missing defines from linux-omap
tree. Also some changes to make room for adding 34xx in
following patches.
Note that the I2C resources are now set up in
arch/arm/plat-omap/i2c.c helper, and can be removed
from devices.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix sparse, checkpatch warnings fro GPMC code.
Also change to use ioremap, and add missing function prototypes
to gpmc.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pinmux support for OMAP3. Incorporated review comments
from Tony to make mux_value as bit mask. Tested on 3430SDP.
Also merge in adding of I2C pins from Jarkko Nikula.
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some register offsets are different for 242x and 243x. This
will allow compiling sleep code for both chips into the same
kernel. Pass the addresses for SDRC_DDLA_CTRL and SDRC_POWER to the
omap24xx_cpu_suspend instead of loading the values since the only.
Also fix a bug to call omap2_sram_suspend with the value of SDRC_DLLA_CTRL
instead of the address as that's what omap24xx_cpu_suspend expects to
determine between DDR and SDR. This bug has not been noticed as
the boards seem to have DDR instead of SDR.
Note that some PM patches are still missing. The PM patches will
be added later on once the base files are in sync with linux-omap
tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common function to enable/disable omap2/3 uart
clocks. Enabled uarts are passed by bootloader in atags and clocks for
these enabled uarts are touched.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpio.c wilfully casts physical addresses to void __iomem * and then
fixes them up at runtime using:
bank->base = IO_ADDRESS(bank->base);
where accesses prior to this fixup are via omap_read/omap_write, and
after are by __raw_read/__raw_write. This doesn't lend itself to
static checking, nor to easy understanding of the code.
And so, OMAP_MPUIO_BASE gets to be the right type - integer like since
it's a physical address, not a MMIO pointer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies
for use with __raw_{read|write}* for accessing registers. Therefore,
these macros should return (void __iomem *) cookies, not integer values.
Doing this improves typechecking, and means we can find those places
where, eg, DMA controllers are incorrectly given virtual addresses to
DMA to, or physical addresses are thrown through a virtual to physical
address translation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make is_omap_port() take the uart_8250_port structure so it can do
whatever test it desires. Convert the test to compare the physical
addresses rather than virtual addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mcbsp is confused as to what takes a physical or virtual address.
Fix the two instances where it gets it wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
