idedisk_supports_hpa() -> ata_id_hpa_enabled().
The latter one also checks validity of words 82 & 85.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace open-coded check by ata_id_wcache_enabled()
(which also checks validity of word 85).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace open-coded checks by ata_id_current_chs_valid().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out HDIO_[OBSOLETE,GET]_IDENTITY ioctls handling
to ide_get_identity_ioctl().
* Use temporary buffer in ide_get_identity_ioctl() instead
of accessing drive->id directly.
* Add ide_id_to_hd_driveid() inline to convert raw id into
struct hd_driveid format (needed on big-endian).
* Use ide_id_to_hd_driveid() in ide_get_identity_ioctl(),
cleanup ide_fix_driveid() and switch ide to use use raw id.
* Remove no longer needed drive->driveid.
This leaves us with 3 users of struct hd_driveid in tree:
- arch/um/drivers/ubd_kern.c
- drivers/block/xsysace.c
- drivers/usb/storage/isd200.c
While at it:
* Use ata_id_u{32,64}() and ata_id_has_{dma,lba,iordy}() macros.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make drive->id an unnamed union so id can be accessed either by using
'u16 *id' or 'struct hd_driveid *driveid'. Then convert all existing
drive->id users accordingly (using 'u16 *id' when possible).
This is an intermediate step to make ide 'struct hd_driveid'-free.
While at it:
- Add missing KERN_CONTs in it821x.c.
- Use ATA_ID_WORDS and ATA_ID_*_LEN defines.
- Remove unnecessary checks for drive->id.
- s/drive_table/table/ in ide_in_drive_list().
- Cleanup ide_config_drive_speed() a bit.
- s/drive1/dev1/ & s/drive0/dev0/ in ide_undecoded_slave().
v2:
Fix typo in drivers/ide/ppc/pmac.c. (From Stephen Rothwell)
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove superfluous checks for drive->mult_req.
* No need to zero drive's fields.
* Move the common code out of #ifdef scope.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This condition is checked by both ide_disk_init_mult_count()
and set_multcount() so no need to do it again in ide_disk_special().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The format specifier for rq->sector didn't specify the proper size and
signedness. Borislav Petkov discovered that the signedness for
rq->nr_sectors and rq->current_nr_sectors also were incorrect.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: remove trailing whitespace]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that disk and partition handlings are mostly unified, it's easy to
allow disk to have extended device number. This patch makes
add_disk() use extended device number if disk->minors is zero. Both
sd and ide-disk are updated to use this.
* sd_format_disk_name() is implemented which can generically determine
the drive name. This removes disk number restriction stemming from
limited device names.
* If sd index goes over SD_MAX_DISKS (which can be increased now BTW),
sd simply doesn't initialize minors letting block layer choose
extended device number.
* If CONFIG_DEBUG_EXT_DEVT is set, both sd and ide-disk always set
minors to 0 and use extended device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With previous changes, it's meaningless to limit the number of
partitions. Replace @ext_minors with GENHD_FL_EXT_DEVT such that
setting the flag allows the disk to have maximum number of allowed
partitions (only limited by the number of entries in parsed_partitions
as determined by MAX_PART constant).
This kills not-too-pretty alloc_disk_ext[_node]() functions and makes
@minors parameter to alloc_disk[_node]() unnecessary. The parameter
is left alone to avoid disturbing the users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement {disk|part}_to_dev() and use them to access generic device
instead of directly dereferencing {disk|part}->dev. To make sure no
user is left behind, rename generic devices fields to __dev.
This is in preparation of unifying partition 0 handling with other
partitions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Extended devt introduces non-contiguos device numbers. This patch
implements a debug option which forces most devt allocations to be
from the extended area and spreads them out. This is enabled by
default if DEBUG_KERNEL is set and achieves...
1. Detects code paths in kernel or userland which expect predetermined
consecutive device numbers.
2. When something goes wrong, avoid corruption as adding to the minor
of earlier partition won't lead to the wrong but valid device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Update sd and ide-disk such that they can take advantage of extended
minors.
ide-disk already has 64 minors per device and currently doesn't use
extended minors although after this patch it can be turned on by
simply tweaking constants.
sd only had 16 minors per device causing problems on certain peculiar
configurations. This patch lifts the restriction and enables it to
use upto 64 minors.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The Optiarc DVD RW AD-7200A can play audio, but tells it could not.
Signed-off-by: Bodo Eggert <7eggert@gmx.de>
Tested-by: Nick Warne <nick@ukfsn.org>
Received-from: Borislav Petkov <petkovbb@googlemail.com>
[bart: keep "audio" quirks together]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check. So, we must never try
to "split" the PRD for TRM290.
This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=11602.
A more generic fix for drives which cannot autoclose tray will follow.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
[bart: add an extra parentheses for consistency with the rest of kernel code]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Enabling IDE generic may prevent ATA controllers located on legacy
ports from being attached to more proper driver or can prevent other
controllers which share the IRQ from working. Note it in the help
message.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: xerces8 <xerces8@butn.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: stein@hermes.si
[bart: s/will grab/may grab/ since Borislav has fixed PCI-case for .28]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove superfluous two bytes from each string buffer and add proper length
format specifiers.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Mark de Wever <koraq@xs4all.nl>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If things are just right this will result in the hws[0]->parent being
passed to ide_host_add() being non-zero and an ooops a little later.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We still have life time issues with the sysfs command filter kobject,
so disable it for 2.6.27 release. We can revisit this and make it work
properly for 2.6.28, for 2.6.27 release it's too risky.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
git commit 74811f355f causes crash at
module load (or boot) time on my machine with a hpt374 controller.
The reason for this is that for initializing second controller which sets
(hwif->dev == host->dev[1]) to true (1), adds 1 to a void ptr, which
advances it by one byte instead of advancing it by sizeof(hpt_info) bytes.
Because of this, all initialization functions get corrupted data in info
variable which causes a crash at boot time.
This patch fixes that and makes my machine boot again.
The card itself is a HPT374 raid conroller: Here is the lspci -v output:
03:06.0 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 8000 [size=8]
I/O ports at 7800 [size=4]
I/O ports at 7400 [size=8]
I/O ports at 7000 [size=4]
I/O ports at 6800 [size=256]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
03:06.1 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 9800 [size=8]
I/O ports at 9400 [size=4]
I/O ports at 9000 [size=8]
I/O ports at 8800 [size=4]
I/O ports at 8400 [size=256]
Capabilities: [60] Power Management version 2
Signed-off-by: Masoud Sharbiani <masouds@google.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: use dev_get_drvdata() per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* fix device tree ... don't forget to set the parent device
* let init/exit code be removed where practical
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
[bart: splitted it from bigger DaVinci patch, s/hw.parent/hw.dev/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch remove blk_register_filter and blk_unregister_filter in
gendisk, and adds them to sd.c, sr.c. and ide-cd.c
The commit abf5439370 moved cmdfilter
from gendisk to request_queue. It turned out that in some subsystems
multiple gendisks share a single request_queue. So we get:
Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x00000000-0x01c00000 : "User FS"
0x01c00000-0x01c40000 : "booter"
kobject (8511c410): tried to init an initialized object, something is seriously wrong.
Call Trace:
[<8036644c>] dump_stack+0x8/0x34
[<8021f050>] kobject_init+0x50/0xcc
[<8021fa18>] kobject_init_and_add+0x24/0x58
[<8021d20c>] blk_register_filter+0x4c/0x64
[<8021c194>] add_disk+0x78/0xe0
[<8027d14c>] add_mtd_blktrans_dev+0x254/0x278
[<8027c8f0>] blktrans_notify_add+0x40/0x78
[<80279c00>] add_mtd_device+0xd0/0x150
[<8027b090>] add_mtd_partitions+0x568/0x5d8
[<80285458>] physmap_flash_probe+0x2ac/0x334
[<802644f8>] driver_probe_device+0x12c/0x244
[<8026465c>] __driver_attach+0x4c/0x84
[<80263c64>] bus_for_each_dev+0x58/0xac
[<802633ec>] bus_add_driver+0xc4/0x24c
[<802648e0>] driver_register+0xcc/0x184
[<80100460>] _stext+0x60/0x1bc
In the long term, we need to fix such subsystems but we need a quick
fix now. This patch add the command filter support to only sd and sr
though it might be useful for other SG_IO users (such as cciss).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* pcmcia-config-loop:
pcmcia: pcmcia_config_loop() improvement by passing vcc
pcmcia: pcmcia_config_loop() default CIS entry handling
pcmcia: pcmcia_config_loop() ConfigIndex unification
pcmcia: use pcmcia_loop_config in misc pcmcia drivers
pcmcia: use pcmcia_loop_config in net pcmcia drivers
pcmcia: use pcmcia_loop_config in ISDN pcmcia drivers
pcmcia: use pcmcia_loop_config in scsi pcmcia drivers
pcmcia: use pcmcia_loop_config in bluetooth drivers
pcmcia: use pcmcia_loop_config in pata and ide drivers
pcmcia: add pcmcia_loop_config() helper
* pcmcia-printk:
pcmcia: don't add extra DEBUG cflag
pcmcia: remove unused cs_socket_name() definition
pcmcia: use dev_printk in module rsrc_nonstatic
pcmcia: use dev_printk in module pcmcia
pcmcia: use dev_printk in module pcmcia_core
pcmcia: use dev_printk and dev_dbg in yenta_socket
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the config loop helper in pata_pcmcia and ide_cs
CC: Tejun Heo <htejun@gmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Over time, a few differences have accumulated between pata_pcmcia
and ide-cs. Fix those.
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
There can be more than one sgiioc4 card in the system so print
also PCI device name on resource allocation failure (so we know
which one is the problematic one).
Reported-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ide-cd to use the new bcd2bin/bin2bcd functions instead of the
obsolete BCD2BIN/BIN2BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch adds missing __devexit_p's.
Reported-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we have warm-plug support ->cable_detect method no longer
can be be marked __devinit.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that we have warm-plug support ->quirkproc method no longer
can be be marked __devinit.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on sparse comments in OpenFirmware code
(no Cx5510/Cx5520 datasheet here).
This fixes 2.6.26 regression reported by TAKADA
and caused by addition of warm-plug support.
Tested-by: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Aesthetic regards aside, commit e8e7b9eb11
still leaves a bug in the error message, because it uses the unconverted
big-endian value for printk.
Fix this by using a local variable in machine byte order. The result is
correct, more readable, and also produces slightly shorter code on i386.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: __u32 -> u32]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The benefits of a user settable CONFIG_IDE_MAX_HWIFS have become pretty
tiny and are no longer considered worth the trouble of an own option.
Simply always #define MAX_HWIFS to 10.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Monday 28 July 2008, Benjamin Herrenschmidt wrote:
[...]
> Vector: 300 (Data Access) at [c58b7b80]
> pc: c014f264: elv_may_queue+0x10/0x44
> lr: c0152750: get_request+0x2c/0x2c0
> sp: c58b7c30
> msr: 1032
> dar: c
> dsisr: 40000000
> current = 0xc58aaae0
> pid = 854, comm = media-bay
> enter ? for help
> mon> t
> [c58b7c40] c0152750 get_request+0x2c/0x2c0
> [c58b7c70] c0152a08 get_request_wait+0x24/0xec
> [c58b7cc0] c0225674 ide_cd_queue_pc+0x58/0x1a0
> [c58b7d40] c022672c ide_cdrom_packet+0x9c/0xdc
> [c58b7d70] c0261810 cdrom_get_disc_info+0x60/0xd0
> [c58b7dc0] c026208c cdrom_mrw_exit+0x1c/0x11c
> [c58b7e30] c0260f7c unregister_cdrom+0x84/0xe8
> [c58b7e50] c022395c ide_cd_release+0x80/0x84
> [c58b7e70] c0163650 kref_put+0x54/0x6c
> [c58b7e80] c0223884 ide_cd_put+0x40/0x5c
> [c58b7ea0] c0211100 generic_ide_remove+0x28/0x3c
> [c58b7eb0] c01e9d34 __device_release_driver+0x78/0xb4
> [c58b7ec0] c01e9e44 device_release_driver+0x28/0x44
> [c58b7ee0] c01e8f7c bus_remove_device+0xac/0xd8
> [c58b7f00] c01e7424 device_del+0x104/0x198
> [c58b7f20] c01e74d0 device_unregister+0x18/0x30
> [c58b7f40] c02121c4 __ide_port_unregister_devices+0x6c/0x88
> [c58b7f60] c0212398 ide_port_unregister_devices+0x38/0x80
> [c58b7f80] c0208ca4 media_bay_step+0x1cc/0x5c0
> [c58b7fb0] c0209124 media_bay_task+0x8c/0xcc
> [c58b7fd0] c00485c0 kthread+0x48/0x84
> [c58b7ff0] c0011b20 kernel_thread+0x44/0x60
The guilty commit turned out to be 08da591e14
("ide: add ide_device_{get,put}() helpers"). ide_device_put() is called
before kref_put() in ide_cd_put() so IDE device is already gone by the time
ide_cd_release() is reached.
Fix it by calling ide_device_get() before kref_get() and ide_device_put()
after kref_put() in all affected device drivers.
v2:
Brown paper bag time. In v1 cd->drive was referenced after dropping last
reference on cd object (which could result in OOPS in ide_device_put() as
reported/debugged by Mariusz Kozlowski). Fix it by caching cd->drive in
the local variable (fix other device drivers too).
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix byte-swapping for id->words161_175[], id->words206_254[]
and id->words206_254[].
Luckily all words previously left in little-endian byte-order
are marked as reserved so this fix shouldn't affect user-space
applications.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
id->tDMA is of 'unsigned char' type so endianness is already
correct and calling le16_to_cpu() is wrong.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The current ide-pmac calls media_bay_set_ide_infos() with an
uninitialized "hwif" argument. The proper fix is to split the
allocation of the hwif from its registration in order to properly
setup the mediabay informations before registration.
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
IDE probing code used to skip devices attached to EATA SCSI HBA
in ATA emulating mode but because of warm-plug support port I/O
resources are no longer freed if no devices are detected on a port
and the decision about the driver to use is left up to the user.
Remove no longer valid EATA SCSI HBA quirk from do_identify().
Noticed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is already done by task_no_data_intr() and there is no reason
not to do it in other TASKFILE_NO_DATA data phase handlers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove the ancient version history. Git does a better job.
From: Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
cdrom_read_capacity() will blindly return the capacity from the device
without sanity-checking it. This later causes code in fs/buffer.c to
oops.
Fix this by checking that the device is telling us sensible things.
From: Jens Axboe <jens.axboe@oracle.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@kernel.org>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[bart: print device name instead of driver name]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[harvey: blocklen is a big-endian value]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
"gayle: reserve memory resources at once" patch temporary removed
freeing of resources on failure (to ease convertion to ide_host_add()
interface). This patch fixes it.
Thanks to Geert for noticing the issue.
Noticed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This controller supports UltraDMA up to mode 5 but it should be clocked with
at least twice the data strobe frequency, so enable mode 5 for 100+ MHz IDECLK.
While at it, start passing the correct device to clk_get() -- it worked anyway
but WTF? :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If this is actually unaligned the access of speed/max_speed above
is already broken and needs a get_unaligned. Otherwise it is
aligned and they can be removed.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
* it821x_chipsets[] -> it821x_chipset.
* Fix it821x_chipset's name field (as it is used for IT8211/8212).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
* Apply small fixes to messages (s/dma/DMA/, remove trailing '.', etc).
* Fix printk() call in ide_setup_pci_baseregs() to use KERN_INFO.
* Move printk() call from ide_pci_clear_simplex() to the caller.
* Cleanup do_ide_setup_pci_device() a bit.
* amd74xx.c: remove superfluous PCI device revision information.
* hpt366.c: fix two printk() calls in ->init_chipset to use KERN_INFO.
* pdc202xx_new.c: fix printk() call in ->init_chipset to use KERN_INFO.
* pdc202xx_old.c: fix driver message in pdc202xx_init_one().
* via82cxxx.c: fix driver warning message in via_init_one().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace ide_default_{io_base,irq}() inlines by legacy_{bases,irqs}[].
v2:
Add missing zero-ing of hws[] (caught during testing by Borislav Petkov).
v3:
Fix zero-oing of hws[] for _real_ this time.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_probe_legacy() call to ide_generic_init() so it fails
early if necessary and returns the proper error value (nowadays
ide_default_io_base() is used only by ide-generic).
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'unsigned long host_flags' field to struct ide_host.
* Set ->host_flags in ide_host_alloc_all().
* Always set PCI dev's ->driver_data in ide_pci_init_{one,two}().
* Add ide_pci_remove() helper (the default implementation for
struct pci_driver's ->remove method).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move the boot message and via_clock setup from
init_chipset_via82cxxx() to via_init_one().
* Set vdev->via_config in via_init_one() and cleanup
init_chipset_via82cxxx() accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove verbose reporting for CMD646 (PCI device revision is always
logged by IDE PCI layer).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Reserve PCI BAR 5 in tc86c001_init_one() and remove no longer needed
init_chipset_tc86c001().
While at it:
* Add & use DRV_NAME define.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
* Reserve PCI BAR 5 in siimage_init_one() and remove no longer needed
setup_mmio_siimage().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
* Allocate both struct it821x_dev instances at once.
* Don't leak itdevs on ide_pci_init_one() failure.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
* Allocate both struct hpt_info instances at once.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct ide_host *host' field to ide_hwif_t and set it
in ide_host_alloc_all().
* Add ide_device_{get,put}() helpers loosely based on SCSI's
scsi_device_{get,put}() ones.
* Convert IDE device drivers to use ide_device_{get,put}().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct device *dev[2]' and 'void *host_priv' fields
to struct ide_host.
* Set ->dev[] in ide_host_alloc_all()/ide_setup_pci_device[s]().
* Pass 'void *priv' argument to ide_setup_pci_device[s]()
and use it to set ->host_priv.
* Set PCI dev's ->driver_data to point to the struct ide_host
instance if PCI host driver wants to use ->host_priv.
* Rename ide_setup_pci_device[s]() to ide_pci_init_{one,two}().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Call ide_pci_setup_ports() before do_ide_setup_pci_device()
in ide_setup_pci_device[s]().
While at it:
* Remove stale FIXMEs.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* If device is in the PCI native mode respect dev->irq regardless of
'tried_config' in do_ide_setup_pci_device().
* Drop no longer needed 'config' argument from ide_setup_pci_controller().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_cd_queue_pc should be checked as the bufflen arg is
dereferenced and lots of callers are passing in NULL.
drivers/ide/ide-cd_ioctl.c:124:46: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:149:47: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:231:46: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:374:46: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
[bart: IDE_FLAG_* -> IDE_AFLAG_*, dev_flags -> atapi_flags]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
[bart: IDE_FLAG_* -> IDE_AFLAG_*, dev_flags -> atapi_flags]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
while at it, remove PC_FLAG_ZIP_DRIVE from the packed command flags altogether
and query the drive type through drive->atapi_flags.
v2:
ide-floppy fix.
There should be no functionality change resulting from this patch.
[bart: IDE_FLAG_* -> IDE_AFLAG_*, dev_flags -> atapi_flags]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
[bart: s/HWGROUP(drive)/hwif->hwgroup/]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make a redundant copy of the packet command bits into rq->cmd. Later, after
all drivers have been converted, it'll be switched to use that in the
common code instead of pc->c. While at it, simplify ide_tape_create_rw_cmd.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-tape uses rq->cmd for special commands from the chrdev interface so move
those to byte 13 (BLK_MAX_CDB = 16) since a packet cmd is max 12 bytes.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make a redundant copy of the packet command bits into rq->cmd.
Later, after all drivers have been converted, it'll be
switched to use that in the common code instead of pc->c.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The if-else block in the IRQ handler is only temporary so that bisect searches
don't break and it'll be removed after converting the remainder of the drivers.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is important that drive->pc_callback is set prior to enabling IRQs on the
device since this is called from the IRQ handler. Otherwise it hurts as I learnt
the hard way from the several "Kernel panic - not synching: Fatal exception in
interrupt" during the weekend :).
The if-else block in the IRQ handler is only temporary so that bisect searches
don't break and it'll be removed after converting the remainder of the drivers.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Coverity CID: 2336 USE_AFTER_FREE
drivers/ide/ide-tape.c ide_tape_kfree_buffer() double free's a pointer
(hint freed by an alias in first outer loop).
This patch simply removes the superfluous kfree().
Signed-off-by: Darren Jenkins <darrenrjenkins@gmailcom>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: gadio@netvision.net.il
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_host_free() helper and convert ide_host_remove() to use it.
* Fix handling of ide_host_register() failure in ide_host_add(),
icside.c, ide-generic.c, falconide.c and sgiioc4.c.
While at it:
* Fix handling of ide_host_alloc_all() failure in ide-generic.c.
* Fix handling of ide_host_alloc() failure in falconide.c
(also return the correct error value if no device is found).
v2:
* falconide build fix. (From Stephen Rothwell)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_ports[] table keeping pointers to all initialized ports.
* Set ide_ports[] entry for a given port in init_irq() and clear it
ide_remove_port_from_hwgroup().
* Convert init_irq() to use ide_ports[] instead of ide_hwifs[] for
grouping ports into hwgroup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_find_port_slot() return port slot index.
* Add ide_free_port_slot() helper.
* Move ide_init_port_data() call and error printk() from
ide_find_port_slot() to ide_host_alloc_all().
* Make ide_{find,free}_port_slot() take ide_cfg_mtx mutex
and convert them use ide_indexes bitmap to keep track of
reserved port slots.
* Don't set hwif->chipset in ide_host_alloc_all() as it is
no longer necessary.
v2:
* Pass the correct slot index to ide_init_port_data().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix ide_host_register() to fail only if all ports cannot be registered.
While at it:
* Use host->ports[] instead of ide_hwifs[] and remove idx[].
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_host_add() helper which does ide_host_alloc()+ide_host_register(),
then convert ide_setup_pci_device[s](), ide_legacy_device_add() and some
host drivers to use it.
While at it:
* Fix ide_setup_pci_device[s](), ide_arm.c, gayle.c, ide-4drives.c,
macide.c, q40ide.c, cmd640.c and cs5520.c to return correct error value.
* -ENOENT -> -ENOMEM in rapide.c, ide-h8300.c, ide-generic.c, au1xxx-ide.c
and pmac.c
* -ENODEV -> -ENOMEM in palm_bk3710.c, ide_platform.c and delkin_cb.c
* -1 -> -ENOMEM in ide-pnp.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_host which keeps pointers to host's ports.
* Add ide_host_alloc[_all]() and ide_host_remove() helpers.
* Pass 'struct ide_host *host' instead of 'u8 *idx' to
ide_device_add[_all]() and rename it to ide_host_register[_all]().
* Convert host drivers and core code to use struct ide_host.
* Remove no longer needed ide_find_port().
* Make ide_find_port_slot() static.
* Unexport ide_unregister().
v2:
* Add missing 'struct ide_host *host' to macide.c.
v3:
* Fix build problem in pmac.c (s/ide_alloc_host/ide_host_alloc/)
(Noticed by Stephen Rothwell).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_tp_ops for transport methods.
* Add 'const struct ide_tp_ops *tp_ops' to struct ide_port_info
and ide_hwif_t.
* Set the default hwif->tp_ops in ide_init_port_data().
* Set host driver specific hwif->tp_ops in ide_init_port().
* Export ide_exec_command(), ide_read_status(), ide_read_altstatus(),
ide_read_sff_dma_status(), ide_set_irq(), ide_tf_{load,read}()
and ata_{in,out}put_data().
* Convert host drivers and core code to use struct ide_tp_ops.
* Remove no longer needed default_hwif_transport().
* Cleanup ide_hwif_t from methods that are now in struct ide_tp_ops.
While at it:
* Use struct ide_port_info in falconide.c and q40ide.c.
* Rename ata_{in,out}put_data() to ide_{in,out}put_data().
v2:
* Fix missing convertion in ns87415.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'config' field to hw_regs_t and use it to set hwif->config_data in
ide_init_port_hw(), then convert ide_legacy_init_one() to use hw->config.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't skip probing IDE port if the corresponding ide_hwifs[] slot
is already occupied.
* Remove duplicate idx[i] assignment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Reserve memory resources for all IDE ports at once by moving
request_mem_region() out of 'for ()' loop and always defining
GAYLE_IDEREG_SIZE to 0x2000.
* Keep memory resources even if no free IDE slots can be found
(this driver is unloadable currently).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Filter out "default" transfer mode values (0x00 - default PIO mode,
0x01 - default PIO mode w/ IORDY disabled) in write handler for obsoleted
/proc/ide/hd?/settings:current_speed setting.
Allowing "default" transfer mode values is a dangerous thing to do as
we don't support programming controller to the "default" transfer mode
and devices often use different values for the default and maximum PIO
mode (i.e. PIO2 default and PIO4 maximum) so the controller will stay
programmed for higher PIO mode while device will use the lower PIO mode.
There is no functionality loss as by using special IOCTLs device can
still be programmed to "default" transfer modes (it is only useful for
debugging/testing purposes anyway).
* Remove no longer needed IDE_HFLAG_ABUSE_SET_DMA_MODE host flag, it was
previously used by few host drivers to program the controller to PIO0
timings for "default" transfer mode == 0x01 (although some host drivers
would program invalid PIO timings instead).
* Cleanup ide_set_xfer_rate() and add BUG_ON().
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Filter out invalid transfer mode values (0x02-0x07) in write handler
for obsoleted /proc/ide/hd?/settings:current_speed setting.
While at it:
* Use XFER_UDMA_6 define.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Lets remove dead Virtual DMA support for now so it doesn't clutter
core IDE code (it can be bring back when there is a need for it):
* Remove IDE_HFLAG_VDMA host flag.
* Remove ide_drive_t.vdma flag.
* cs5520.c: remove stale FIXMEs, cs5520_dma_host_set() and cs5520_dma_ops
(also there is no longer a need to set IDE_HFLAG_NO_ATAPI_DMA).
There should be no functional changes caused by this patch.
Cc: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan Cox has noticed some time ago that hpt34x is broken
(http://lkml.org/lkml/2007/7/3/257):
"No the old driver doesn't even do that. It starts up. It spuriously
adjusts some non writable PCI BAR registers, prints a message about
resources being in use already then exits."
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer needed ->INB, ->OUTB and ->OUTBSYNC methods.
Then:
* Remove no longer used default_hwif_[mm]iops() and ide_[mm_]outbsync().
* Cleanup SuperIO handling in ns87415.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_read_bcount_and_ireason() helper and use it instead of ->INB
in {cdrom_newpc,ide_pc}_intr().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_read_ireason() helper and use instead of ->INB for reading
ATAPI Interrupt Reason register.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_IN_FEATURE taskfile flag for reading Feature
register and handle it in ->tf_read.
* Convert ide_read_error() to use ->tf_read instead of ->INB,
then uninline and export it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert SELECT_DRIVE() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert actual_try_to_identify() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert ide_config_drive_speed() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Write ATA Feature register before ATA Sector Count register as
a preparation to use ->tf_load in ide_config_drive_speed().
This change shouldn't affect anything (just an usual paranoia).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().
While at it:
* Use ->set_irq in init_irq() and do_reset1().
* Don't use HWIF() macro in ide_check_pm_state().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_read_altstatus() inline helper.
* Add ->read_altstatus method for reading ATA Alternate Status
register and use it instead of ->INB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_read_status() inline helper.
* Add ->read_status method for reading ATA Status register
and use it instead of ->INB.
While at it:
* Don't use HWGROUP() macro.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out simplex handling from ide_pci_dma_base() to
ide_pci_check_simplex().
* Set hwif->dma_base early in ->init_dma method / ide_hwif_setup_dma()
and reset it in ide_init_port() if DMA initialization fails.
* Use ->read_sff_dma_status instead of ->INB in ide_pci_dma_base().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Export sff_dma_ops and then remove ide_setup_dma().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->dma_base + offset instead of ->dma_{status,command}
and remove no longer needed ->dma_{status,command}.
While at it:
* Use ATA_DMA_* defines.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use I/O ops directly in ide_dma_host_set(), ide_dma_setup(),
ide_dma_start() and __ide_dma_end().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->read_sff_dma_status method for reading DMA Status register
and use it instead of ->INB.
While at it:
* Use inb() directly in ns87415.c::ns87415_dma_end().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'hw_regs_t **hws' argument to ide_device_add[_all]() and convert
host drivers + ide_legacy_init_one() + ide_setup_pci_device[s]() to use
it instead of calling ide_init_port_hw() directly.
[ However if host has > 1 port we must still set hwif->chipset to hint
consecutive ide_find_port() call that the previous slot is occupied. ]
* Unexport ide_init_port_hw().
v2:
* Use defines instead of hard-coded values in buddha.c, gayle.c and q40ide.c.
(Suggested by Geert Uytterhoeven)
* Better patch description.
v3:
* Fix build problem in ide-cs.c. (Noticed by Stephen Rothwell)
There should be no functional changes caused by this patch.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_pci_setup_ports() call out from do_ide_setup_pci_device()
to ide_setup_pci_device[s]().
* Drop no longer needed idx argument from do_ide_setup_pci_device().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_find_port() call to pmac_ide_setup_device().
While at it:
- fix return value (s/-ENODEV/-ENOENT/)
- add DRV_NAME define and use it to set name field of pmac_port_info
- use ide_find_port_slot() instead of ide_find_port()
- remove superfluous error message (ide_find_port_slot() takes care of it)
- drop IDE interface number from driver banner message (but include bus type)
v2:
* Build fix (thanks to Stephen Rothwell for noticing the issue).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass pmif instead of hwif to pmac_ide_do_{suspend,resume}().
* Store pmif instead of hwif in ->driver_data.
* Use dev_get_drvdata() instead of ->hwif_data to obtain pmif.
v2:
* Build fixes from Stephen Rothwell.
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that each error condition during the execution of an
HDIO_DRIVE_RESET ioctl is actually reported to the calling process.
Also, unify the exit path of reset_pollfunc() when returning ide_stopped
since the need of ->port_ops->reset_poll() to be treated specially has
vanished (way back, it seems).
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove some code which has been made obsolete and hasn't worked properly
before anyway. Part of the infrastructure may be reintroduced in a
follow up patch to implement a working command aborting facility.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently, the code path executing an HDIO_DRIVE_RESET ioctl is broken
in various ways. Most importantly, it is treated as an out of band
request in an illegal way which may very likely lead to system lock ups.
Use the drive's request queue to avoid this problem (and fix a locking
issue for free along the way).
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch moves hd.c to drivers/block/
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the later move to drivers/block/ will break the link order,
the module_init() has to become a late_initcall().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After commit 80aa31cb46
(ide: remove CONFIG_BLK_DEV_HD_IDE config option (take 2))
the indirection through BLK_DEV_HD_ONLY is no longer required.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a precaution just to make sure a new pc is clean when allocated.
There should be no functional change introduced by this patch.
[bart: ported it over IDE changes]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There's no need for this function since it is used only once.
[bart: ported it over IDE changes]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As a nice side effect, this minimizes the IRQ handler execution time.
There should be no functionality change resulting from this patch.
[bart: remove extra newlines from ide_cd_do_request()]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... by factoring out the rq preparation code into a separate
function called in the request routine. As a nice side effect,
this minimizes the IRQ handler execution time.
There should be no functionality change resulting from this patch.
[bart: s/HWGROUP()/drive->hwif->hwgroup/ and remove extra newline]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... by factoring out the rq preparation code into a separate
function called in the request routine. As a nice side effect,
this minimizes the IRQ handler execution time.
There should be no functionality change resulting from this patch.
[bart: s/HWGROUP()/drive->hwif->hwgroup/ and remove extra newlines]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do what the compiler does anyway: inline a function that is used only once.
This saves us the overhead of a function call and the function is small enough
to be embedded in the callsite anyways.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Call cdrom_start_packet_command() only from the ->do_request() routine.
As a nice side effect, this improves code readability a bit.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is done in the request issue path anyway.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_find_port_slot() call closer to ide_device_add().
This is basically a preparation for the future changes.
Cc: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_find_port_slot() call closer to ide_device_add().
This is basically a preparation for the future changes.
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Try to probe first interface even if ide_hwifs[]'s slot for the second
interface cannot be obtained.
While at it:
- Add DRV_NAME define and use it for request_dma() instead of hwif->name.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Return -ENOENT on ide_find_port() failure.
While at it:
- Cleanup rapide_probe() a bit.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
On Sunday 15 June 2008, Geert Uytterhoeven wrote:
> As ide-taskfile.c uses scatterlists, it should include <linux/scatterlist.h>.
(v1 broke IDE build on m68k, thanks to Geert for finding the bug)
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_set_handler() bugs on ->handler == NULL so no need to do it
in set_geometry_intr().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Allow any command requesting DMA data phase for HDIO_DRIVE_TASKFILE ioctl
and remove no longer needed task_dma_ok()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DRV_NAME define to ide-h8300.c.
* Fix ide-h8300.c, swarm.c and sgiioc4.c to set .name field in
struct ide_port_info to DRV_NAME, then convert these host drivers
to use ide_find_port_slot() instead of ide_find_port().
* Print message on error in ide_find_port_slot().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use ->init_dev method instead of open-coding devices
init in cmd640x_init().
While at it:
- fix printk()-s to use KERN_INFO level instead of the default KERN_ERR
- use DRV_NAME define in printk()-s
- set proper ->pio_mask also for CONFIG_BLK_DEV_CMD640_ENHANCED=n
There should be no functional changes caused by this patch
(except fixing printk()-s levels).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ->port_init_devs method to take 'ide_drive_t *' as an argument
instead of 'ide_hwif_t *' and rename it to ->init_dev.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Register secondary interface also when user requested not to probe devices.
While at it:
- remove write-only second_port_toggled variable
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This driver was only used by arch/ppc code and is obsolete
now with the move to common arch/powerpc code.
[bart: port it over IDE tree, remove leftover 'choice' from Kconfig]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Tested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan has fixed PCI layer handling of PCI IDE in Compatibility mode so
PCI BAR 0/1 (and/or 2/3) content reported by kernel should never be zero.
Tighten checks on PCI BARs and also fix printk() message while on it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_find_port() and default_hwif_mmiops() calls from icside_setup()
to icside_register_v{5,6}().
* Convert icside_setup() to initialize hw_regs_t instead ide_hwif_t
and icside_register_v{5,6}() to use ide_init_port_hw().
* Rename icside_setup() to icside_setup_ports().
There should be no functional changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ecard_set_drvdata() from icside_probe() to icside_register_v{5,6}(),
then use state->ioc_base instead of hwif->hwif_data in icside_maskproc()
and icside_dma_test_irq().
While at it:
* Add sel field to struct icside_state, then use state->{sel,ioc_base}
instead of ->{select,config}_data in icside_dma_setup().
There should be no functional changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info - as a nice side-effect
this fixes hwif->channel initialization.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use &auide_hwif directly instead of using hwif->hwif_data.
While at it:
* No need to initialize hwif->{select,config}_data.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'parent' field to hw_regs_t for optional parent device pointer (needed
by macio PMAC IDE controllers) and set hwif->dev in ide_init_port_hw().
* Update au1xxx-ide.c, sgiioc4.c, pmac.c and setup-pci.c accordingly.
v2:
* Update scc_pata.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move PIO blacklist to ide-pio-blacklist.c.
While at it:
- fix comment
- fix whitespace damage
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All ide_pio_cycle_time() users already select CONFIG_IDE_TIMINGS
so move the function from ide-lib.c to ide-timings.c.
While at it:
- convert ide_pio_cycle_time() to use ide_timing_find_mode()
- cleanup ide_pio_cycle_time() a bit
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also update my Copyrights while at it.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also fix (disabled) debugging code while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't include ide-timing.h in cs5535 and sis5513 host drivers
(they don't need it currently).
* Convert ide-timing.h to ide-timings.c library and add CONFIG_IDE_TIMINGS
config option to be selected by host drivers using the library.
While at it:
- fix ide_timing_find_mode() placement
v2:
* Add missing EXPORT_SYMBOLs. (Stephen Rothwell <sfr@canb.auug.org.au>)
There should be no functional changes caused by this patch.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also fix placement of comments in ide_timing_compute() while at it.
There should be no functional changes caused by this patch
(md5sum was verified to be the same before/after the patch).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check requested xfer mode against xfer modes instead of XFER_* masks
in ide_timing_compute() and cs5535.c::cs5535_set_speed().
* Remove XFER_[MODE,MWDMA,EPIO,PIO] masks.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move struct ide_timing and IDE_TIMING_* defines to <linux/ide.h>
from drivers/ide/ide-timing.h.
While at it:
- use u8/u16 instead of short for struct ide_timing fields
- use enum for IDE_TIMING_*
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove unused XFER_UDMA_SLOW from ide_timing[].
While at it:
- fix re-defining XFER_PIO_5 (no need to define it in ide-timing.h as
it is defined in <linux/ata.h> which is included by <linux/hdreg.h>)
- fix whitespace damage
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove the old BAST IDE driver, as we are now using the platform-pata
support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This uses the dma safe check for REQ_TYPE_ATA_PC. The dma safe check
is used for only sg requests but it should be used for other non fs
commands.
This uses blk_queue_update_dma_pad to make the intention clear though
ide don't use the blk APIs so it doesn't change anything.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some REQ_TYPE_ATA_PC commands uses the stack buffers for DMA, which
leads to memory corruption on a non-coherent platform.
With regard to alignment and padding, ide-cd has the the dma safe
check for sg requests and REQ_TYPE_ATA_PC. This adds the stack buffer
check to that check.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver of ITE8212 in pass-through mode (it8212.noraid=1 on cmndline)
attempts to use the field `.dma_host_set' of the struct ide_dma_ops in
`ide_config_drive_speed' which is set to NULL by default.
So give a value to all fields of the struct ide_dma_ops.
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
