__kuser_cmpxchg64 has a return path using bx lr to get back to the caller.
This is actually ok since the code in question is predicated on
CONFIG_CPU_32v6K, but for the sake of consistency using the usr_ret
macro is probably better.
Acked-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux uses two PMD entries for a PTE with the classic page table format,
covering 2MB range. However, the __pte_free_tlb() function only adds a
single TLB flush corresponding to 1MB range covering 'addr'. On
Cortex-A15, level 1 entries can be cached by the TLB independently of
the level 2 entries and without additional flushing a PMD entry would be
left pointing at the wrong PTE. The patch limits the TLB flushing range
to two 4KB pages around the 1MB boundary within PMD.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 89d6c0b5 ("perf, arch: Add generic NODE cache events") added
empty NODE event definitions for the ARM PMU implementations. This was
merged along with Cortex-A5 and Cortex-A15 PMU support, so they missed
out on the original patch.
This patch adds the empty definitions to Cortex-A5 and Cortex-A15.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we are context switched whilst copying into a thread's
vfp_hard_struct then the partial copy may be corrupted by the VFP
context switching code (see "ARM: vfp: flush thread hwstate before
restoring context from sigframe").
This patch updates the ptrace VFP set code so that the thread state is
flushed before the copy, therefore disabling VFP and preventing
corruption from occurring.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In a preemptible kernel, vfp_set() can be preempted, causing the
hardware VFP context to be switched while the thread vfp state is
being read and modified. This leads to a race condition which can
cause the thread vfp state to become corrupted if lazy VFP context
save occurs due to preemption in between the time thread->vfpstate
is read and the time the modified state is written back.
This may occur if preemption occurs during the execution of a
ptrace() call which modifies the VFP register state of a thread.
Such instances should be very rare in most realistic scenarios --
none has been reported, so far as I am aware. Only uniprocessor
systems should be affected, since VFP context save is not currently
lazy in SMP kernels.
The problem was introduced by my earlier patch migrating to use
regsets to implement ptrace.
This patch does a vfp_sync_hwstate() before reading
thread->vfpstate, to make sure that the thread's VFP state is not
live in the hardware registers while the registers are modified.
Thanks to Will Deacon for spotting this.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Following execution of a signal handler, we currently restore the VFP
context from the ucontext in the signal frame. This involves copying
from the user stack into the current thread's vfp_hard_struct and then
flushing the new data out to the hardware registers.
This is problematic when using a preemptible kernel because we could be
context switched whilst updating the vfp_hard_struct. If the current
thread has made use of VFP since the last context switch, the VFP
notifier will copy from the hardware registers into the vfp_hard_struct,
overwriting any data that had been partially copied by the signal code.
Disabling preemption across copy_from_user calls is a terrible idea, so
instead we move the VFP thread flush *before* we update the
vfp_hard_struct. Since the flushing is performed lazily, this has the
effect of disabling VFP and clearing the CPU's VFP state pointer,
therefore preventing the thread from being updated with stale data on
the next context switch.
Cc: stable <stable@vger.kernel.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 3c424f3598.
Joachim Eastwood reports:
| "ARM: 7304/1: ioremap: fix boundary check when reusing static mapping"
| Commit: 3c424f3598 in Linus master
|
| Breaks booting on my custom AT91RM9200 board.
| There isn't any error messages or anything that indicates what goes
| wrong it just stops after; Uncompressing Linux... done, booting the
| kernel.
|
| Reverting it makes my board boot again.
and further debugging reveals:
ioremap: pfn=fffff phys=fffff000 offset=400 size=1000
ioremap: area c3ffdfc0: phys_addr=200000 pfn=200 size=4000
ioremap: found: addr fef74000 => fed73000 => fed73400
Clearly, an area for pfn 0x200, 16K can't ever satisfy a request for pfn
0xfffff. This happens because the changed if statement becomes:
if (0x00200 > 0xfffff ||
0xfffff000 + 0x400 + 0x1000-1 > 0x00200000 + 0x4000-1)
and therefore:
if (0x00200 > 0xfffff ||
0x000003ff > 0x00203fff)
The if condition fails, and so we _believe_ that the SRAM mapping fits
our request. Clearly that's totally bogus.
Moreover, the original premise of the 'fix' patch was wrong:
| The condition checking boundaries of the requested and existing
| mappings didn't take in-page offset into consideration though,
| which lead to obscure and hard to debug problems when requested
| mapping crossed end of the static one.
as the code immediately above this loop does:
size = PAGE_ALIGN(offset + size);
so 'size' already contains the requested offset into the page.
So, revert the broken 'fix'.
Acked-by: Nicolas Pitre <nico@linaro.org>
Since commit 576d2f2525 "ARM: add
generic ioremap optimization by reusing static mappings" ioremap()
is trying to reuse existing static mapping when possible.
The condition checking boundaries of the requested and existing
mappings didn't take in-page offset into consideration though,
which lead to obscure and hard to debug problems when requested
mapping crossed end of the static one.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This macro is used to generate unprivileged accesses (LDRT/STRT) to user
space.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dynamic ftrace ops startup test currently fails on Thumb-2 kernels:
Testing tracer function: PASSED
Testing dynamic ftrace: PASSED
Testing dynamic ftrace ops #1: (0 0 0 0 0) FAILED!
This is because while the addresses in the mcount records do not have
the zero bit set, the IP reported by the mcount call does have it set
(because it is copied from the LR). This mismatch causes the ops
filtering in ftrace_ops_list_func() to not call the relevant tracers.
Fix this by clearing the zero bit before adjusting the LR for the mcount
instruction size. Also, combine the mov+sub into a single sub
instruction.
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 0536bdf33f (ARM: move iotable mappings within
the vmalloc region), the RealView PB11MP cannot boot anymore.
This is caused by the way the mappings are described on this
platform (define replaced by hex values for clarity):
{ /* GIC CPU interface mapping */
.virtual = IO_ADDRESS(0x1F000100),
.pfn = __phys_to_pfn(0x1F000100),
.length = SZ_4K,
.type = MT_DEVICE,
}, { /* GIC distributor mapping */
.virtual = IO_ADDRESS(0x1F001000),
.pfn = __phys_to_pfn(0x1F001000),
.length = SZ_4K,
.type = MT_DEVICE,
}
The first mapping ends up reserving two pages, and clashes with
the second one, which triggers a BUG_ON in vm_area_add_early().
In order to solve this problem, treat the MPCore private memory
region (containing the SCU, the GIC and the TWD) as a single region,
as described in the TRM:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0360f/CACGDJJC.html
The EB11MP is converted the same way, even if it manages to avoid
the problem.
Tested on both PB11MP and EB11MP.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Jornada SSP driver is supposed to be initialized by a
module_init() call, but it was missed at some merge point. Since
the driver mostly pass calls through it magically works anyway,
but needs to be rectified.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On secondary CPUs, the Timer Control Register is not reset
to a sane value before the timer is registered, and the TRM
doesn't seem to indicate any reset value either. In some cases,
the kernel will take an interrupt too early, depending on what
junk was present in the registers at reset time.
The fix is to set the Timer Control Register to 0 before
registering the clock_event_device and enabling the interrupt.
Problem seen on VE (Cortex A5) and Tegra.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On v7, we use the same cache maintenance instructions for data lines
as for unified lines. This was not the case for v6, where HARVARD_CACHE
was defined to indicate the L1 cache topology.
This patch removes the erroneous compile-time check for HARVARD_CACHE in
proc-v7.S, ensuring that we perform I-side invalidation at boot.
Reported-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Catalin Marinas <Catalin.Marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The merging of commits 1b6ba46b ("ARM: LPAE: MMU setup for the 3-level
page table format") and b4244738 ("ARM: 7202/1: Add Cortex-A7 proc info")
during the merge window ended up putting the Cortex-A7 proc_info into a
code block guarded by !CONFIG_ARM_LPAE. This makes Cortex-A7 platforms
unbootable when LPAE is enabled.
This patch moves the proc_info structure for Cortex-A7 outside of the
guarded block.
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It turns out that the logical CPU mapping is useful even when !CONFIG_SMP
for manipulation of devices like interrupt and power controllers when
running a UP kernel on a CPU other than 0. This can happen when kexecing
a UP image from an SMP kernel.
In the future, multi-cluster systems running AMP configurations will
require something similar for mapping cluster IDs, so it makes sense to
decouple this logic in preparation for this support.
Acked-by: Yang Bai <hamo.by@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To ensure correct alignment of cacheline-aligned data, the maximum
cacheline size needs to be known at compile time.
Since Cortex-A8 and Cortex-A15 have 64-byte cachelines (and it is likely
that there will be future ARMv7 implementations with the same line size)
then it makes sense to assume that CPU_V7 implies a 64-byte L1 cacheline
size. For CPUs with smaller caches, this will result in some harmless
padding but will help with single zImage work and avoid hitting subtle
bugs with misaligned data structures.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The exception fixup table is currently aligned to a 32-byte boundary.
Whilst this won't cause any problems, the exception_table_entry
structures contain only a pair of unsigned longs, so 4-byte alignment
is all that is required. If the table was walked from start to end,
cacheline alignment may bring some performance benefits, but since a
binary search is used, the access pattern is random and will not benefit
from a stricter alignment.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The linker script assumes a cacheline size of 32 bytes when aligning
the .data..cacheline_aligned and .data..percpu sections.
This patch updates the script to use L1_CACHE_BYTES, which should be set
to 64 on platforms that require it.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 5dd7bf59e0.
Conflicts:
scripts/mod/file2alias.c
This change is wrong on many levels. First and foremost, it causes a
regression. On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:
ucb1x00 ID not found: 1005
0x1005 is a valid ID for the UCB1300 device.
Secondly, this patch is way over the top in terms of complexity. The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver. Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.
Fix the following build warning:
CC arch/arm/kernel/setup.o
In file included from arch/arm/kernel/setup.c:39:
arch/arm/include/asm/elf.h:102:1: warning: "vmcore_elf64_check_arch" redefined
In file included from arch/arm/kernel/setup.c:24:
include/linux/crash_dump.h:30:1: warning: this is the location of the previous definition
Since commit 93a72052 (crash_dump: export is_kdump_kernel to modules, consolidate elfcorehdr_addr, setup_elfcorehdr and saved_max_pfn)
the inclusion of <linux/crash_dump.h> is no longer needed.
Remove the inclusion of <linux/crash_dump.h> and the build warning is fixed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All other ports use "Kernel code" to identify the Kernel text segment
in /proc/iomem. Change the ARM resources to do the same.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We can stall RCU processing on SMP platforms if a CPU sits in its idle
loop for a long time. This happens because we don't call irq_enter()
and irq_exit() around generic_smp_call_function_interrupt() and
friends. Add the necessary calls, and remove the one from within
ipi_timer(), so that they're all in a common place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0x1bc9c): Section mismatch in reference from the function ct_ca9x4_init_cpu_map() to the function .init.text:scu_get_core_count()
The function ct_ca9x4_init_cpu_map() references
the function __init scu_get_core_count().
WARNING: vmlinux.o(.text+0x1bce8): Section mismatch in reference from the function ct_ca9x4_init_cpu_map() to the function .init.text:set_smp_cross_call()
The function ct_ca9x4_init_cpu_map() references
the function __init set_smp_cross_call().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 716a3dc200 (ARM: Add arm_memblock_steal() to allocate memory
away from the kernel) added a function which calls memblock_alloc().
This causes a section conflict:
WARNING: vmlinux.o(.text+0xc614): Section mismatch in reference from the function arm_memblock_steal() to the function .init.text:memblock_alloc()
The function arm_memblock_steal() references
the function __init memblock_alloc().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: arch/arm/mach-sa1100/built-in.o(.data+0x11b8): Section mismatch in reference from the variable sa1100_driver to the function .init.text:sa1100_cpu_init()
The variable sa1100_driver references
the function __init sa1100_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
f408c985ce (GPIO: sa1100: implement proper gpiolib gpio_to_irq conversion)
made gpio_to_irq() a function. This breaks collie where it's used to
initialize some static data. Fix that by moving the initialization to
the init code.
arch/arm/mach-sa1100/collie.c:139: error: initializer element is not constant
arch/arm/mach-sa1100/collie.c:139: error: (near initialization for 'collie_power_resource[0].start')
arch/arm/mach-sa1100/collie.c:140: error: initializer element is not constant
arch/arm/mach-sa1100/collie.c:140: error: (near initialization for 'collie_power_resource[0].end')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 7cea00657d.
The sa1100 cleanups fatally broke the SA1100 RTC driver - the first
hint that something is wrong are these compiler warnings:
drivers/rtc/rtc-sa1100.c:42:1: warning: "RCNR" redefined
In file included from arch/arm/mach-sa1100/include/mach/hardware.h:73,
from drivers/rtc/rtc-sa1100.c:35:
arch/arm/mach-sa1100/include/mach/SA-1100.h:877:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:43:1: warning: "RTAR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:876:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:44:1: warning: "RTSR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:879:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:45:1: warning: "RTTR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:878:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:47:1: warning: "RTSR_HZE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:891:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:48:1: warning: "RTSR_ALE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:890:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:49:1: warning: "RTSR_HZ" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:889:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:50:1: warning: "RTSR_AL" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:888:1: warning: this is the location of the previous definition
and the second problem, which is far more severe, are the different
register layouts, resulting in the wrong registers being read on
SA11x0 platforms. This patch adds:
#define RCNR 0x00 /* RTC Count Register */
#define RTAR 0x04 /* RTC Alarm Register */
#define RTSR 0x08 /* RTC Status Register */
#define RTTR 0x0c /* RTC Timer Trim Register */
but the SA11x0 registers are:
#define RTAR __REG(0x90010000) /* RTC Alarm Reg. */
#define RCNR __REG(0x90010004) /* RTC CouNt Reg. */
#define RTTR __REG(0x90010008) /* RTC Trim Reg. */
#define RTSR __REG(0x90010010) /* RTC Status Reg. */
Some fallout from the 3.3. merge window as well as a couple bug fixes
for older preexisting bugs that seem valid to include at this time:
* sched_clock changes broke picoxcell, fix included
* BSYM bugs causing issues with thumb2-built kernels on SMP
* Missing module.h include on msm.
* A collection of bugfixes for samsung platforms that didn't make it into
the first pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=+GJ1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
ARM: fixes for ARM platforms
Some fallout from the 3.3. merge window as well as a couple bug fixes
for older preexisting bugs that seem valid to include at this time:
* sched_clock changes broke picoxcell, fix included
* BSYM bugs causing issues with thumb2-built kernels on SMP
* Missing module.h include on msm.
* A collection of bugfixes for samsung platforms that didn't make it into
the first pull requests.
* tag 'arm-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: make BSYM macro assembly only
ARM: highbank: remove incorrect BSYM usage
ARM: imx: remove incorrect BSYM usage
ARM: exynos: remove incorrect BSYM usage
ARM: ux500: add missing ENDPROC to headsmp.S
ARM: msm: Add missing ENDPROC to headsmp.S
ARM: versatile: Add missing ENDPROC to headsmp.S
ARM: EXYNOS: Invert VCLK polarity for framebuffer on ORIGEN
ARM: S3C64XX: Fix interrupt configuration for PCA935x on Cragganmore
ARM: S3C64XX: Fix the memory mapped GPIOs on Cragganmore
ARM: S3C64XX: Remove hsmmc1 from Cragganmore
ARM: S3C64XX: Remove unconditional power domain disables
ARM: SAMSUNG: Declare struct platform_device in plat/s3c64xx-spi.h
ARM: SAMSUNG: dma-ops.h needs mach/dma.h
ARM: SAMSUNG: Guard against multiple inclusion of plat/dma.h
ARM: picoxcell: fix sched_clock() cleanup fallout
ARM: msm: vreg is a module and so needs module.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
audit: no leading space in audit_log_d_path prefix
audit: treat s_id as an untrusted string
audit: fix signedness bug in audit_log_execve_info()
audit: comparison on interprocess fields
audit: implement all object interfield comparisons
audit: allow interfield comparison between gid and ogid
audit: complex interfield comparison helper
audit: allow interfield comparison in audit rules
Kernel: Audit Support For The ARM Platform
audit: do not call audit_getname on error
audit: only allow tasks to set their loginuid if it is -1
audit: remove task argument to audit_set_loginuid
audit: allow audit matching on inode gid
audit: allow matching on obj_uid
audit: remove audit_finish_fork as it can't be called
audit: reject entry,always rules
audit: inline audit_free to simplify the look of generic code
audit: drop audit_set_macxattr as it doesn't do anything
audit: inline checks for not needing to collect aux records
audit: drop some potentially inadvisable likely notations
...
Use evil merge to fix up grammar mistakes in Kconfig file.
Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.
This patch provides functionality to audit system call events on the
ARM platform. The implementation was based off the structure of the
MIPS platform and information in this
(http://lists.fedoraproject.org/pipermail/arm/2009-October/000382.html)
mailing list thread. The required audit_syscall_exit and
audit_syscall_entry checks were added to ptrace using the standard
registers for system call values (r0 through r3). A thread information
flag was added for auditing (TIF_SYSCALL_AUDIT) and a meta-flag was
added (_TIF_SYSCALL_WORK) to simplify modifications to the syscall
entry/exit. Now, if either the TRACE flag is set or the AUDIT flag is
set, the syscall_trace function will be executed. The prober changes
were made to Kconfig to allow CONFIG_AUDITSYSCALL to be enabled.
Due to platform availability limitations, this patch was only tested
on the Android platform running the modified "android-goldfish-2.6.29"
kernel. A test compile was performed using Code Sourcery's
cross-compilation toolset and the current linux-3.0 stable kernel. The
changes compile without error. I'm hoping, due to the simple modifications,
the patch is "obviously correct".
Signed-off-by: Nathaniel Husted <nhusted@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
* 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Invert VCLK polarity for framebuffer on ORIGEN
ARM: S3C64XX: Fix interrupt configuration for PCA935x on Cragganmore
ARM: S3C64XX: Fix the memory mapped GPIOs on Cragganmore
ARM: S3C64XX: Remove hsmmc1 from Cragganmore
ARM: S3C64XX: Remove unconditional power domain disables
ARM: SAMSUNG: Declare struct platform_device in plat/s3c64xx-spi.h
ARM: SAMSUNG: dma-ops.h needs mach/dma.h
ARM: SAMSUNG: Guard against multiple inclusion of plat/dma.h
* 'fixes' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm:
ARM: sa11x0: assabet: fix build warning
ARM: Add arm_memblock_steal() to allocate memory away from the kernel
ARM: 7275/1: LPAE: Check the CPU support for the long descriptor format
ARM: 7274/1: NUC900: Rename nuc900-audio platform device to nuc900-ac97
ARM: 7272/1: S3C24XX: Fix build error for missing <mach/system-reset.h>
ARM: 7271/1: Fix typo in conversion of ARCH_NR_GPIOS to Kconfig
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Hibernate: Drop the check of swap space size for compressed image
PM / shmobile: fix A3SP suspend method
PM / Domains: Skip governor functions for CONFIG_PM_RUNTIME unset
PM / Domains: Fix build for CONFIG_PM_SLEEP unset
PM: Make sysrq-o be available for CONFIG_PM unset
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: Use dtc's -d (dependency) option
dtc: Implement -d option to write out a dependency file
kbuild: Fix comment in Makefile.lib
scripts/genksyms: clean lex/yacc generated files
kbuild: Correctly deal with make options which contain an "s"
Since a32618d2 (ARM: pgtable: switch to use pgtable-nopud.h), assabet
warns as follows:
arch/arm/mach-sa1100/assabet.c: In function 'map_sa1100_gpio_regs':
arch/arm/mach-sa1100/assabet.c:264: warning: passing argument 1 of 'pmd_offset' from incompatible pointer type
Fix this by adding the necessary pud_offset() macro.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so only define it for assembly.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Dave Martin <dave.martin@linaro.org>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so remove it. The linker will correctly set bit 0 for Thumb2
kernels.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Dave Martin <dave.martin@linaro.org>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so remove it. The linker will correctly set bit 0 for Thumb2
kernels.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
BSYM macro is only needed for assembly files and its usage in c files is
wrong, so remove it. The linker will correctly set bit 0 for Thumb2
kernels.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Once the ENDPROC is in place, BSYM() in not longer necessary
to get correct pointer to u8500_secondary_startup().
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
