Hardware related Fixes and Changes.
- Added new Adapter IDs and update default Adapter names.
- Added PCI read after EQarm doorbell PCI write to flush the write
and avoid spurrious interrupts when in INTx mode.
- Phase out use of ONLINE registers.
- Fix for lost MSI interrupt
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix errors relating to crashes and hangs.
- Fix crash due to list corruption while unloading driver.
- Fix panic during pci-hot-plug testing.
- Fix panic when unmapping luns.
- Fixed total_scsi_bufs counting could cause exhausted memory.
- Fixed locking issue causing hang.
- Fixed the call from lpfc_new_scsi_buf_s3 to use lpfc_release_scsi_buf_s3.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix AER issues.
- Made AER sysfs entry point return "Operation not permitted" to
OneConnect HBAs
- Stop and abort all I/Os on HBA for AER uncorrectable non-fatal error
handling
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC protocol fixes.
- Fix send sequence logic to handle multi SGL IOCBs.
- Fix FDISC completion always setting VPORT state to failed.
- Ported the fix on reporting of max_vpi to uppper layer.
- Fix incorrect number of Vports allowed to be created.
- Fixed Dead FCoE port after creating vports.
- Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
- Handle unsolicited CT exchange initiator receiving CT exchange ABTS
- Migrate LUN queue depth ramp up code to scsi mid-layer.
- Made ABTS WQE go to the same WQ as the WQE to be aborted.
- Fix Vport does not rediscover after FCF goes away.
- Fixed lpfc_unreg_vfi failure after devloss timeout.
- Fixed RPI bit leak.
- Fix hbq pointer corruption during target discovery.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FCoE Protocol fixes.
- Fixed FIP frame designation for ELS commands.
- Fix CVL received on Port 1 not processed by driver.
- Fix Zeroed frame on wire after FLOGI
- Fix vport keep-alive does not contain the correct WWN.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following changes:
- Fixed Panic/Hang when using polling mode for fcp commands
- Added support for Read_rev mbox bits indicating FIP mode of HBA
- Optimize performance of slow-path handling of els responses
- Add code to cleanup orphaned unsolicited receive sequences
- Fixed Devloss timeout when multiple initiators are in same zone
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch include the following fixes and changes:
- Fix crash when "error" is echoed to board_mode sysfs parameter
- Fix FCoE Parameter parsing in regions 23
- Fix driver crash when creating vport with large number of targets on SLI4
- Fix bug with npiv message being logged when it is not supported by the adapter
- Fix a potential dereferencing mailbox structure after free bug
- Fix firmware crash after vport create with high target count
- Error out requests to set board_mode to warm restart via sysfs on SLI4 HBAs
- Fix Block guard logging
- Fix a memory corruption issue during GID_FT IO prep
- Fix crash while processing unsolicited FC frames
- Fix failed to allocate XRI message is not a critical failure
- Update and fix formatting in some log messages
- Fix missing new line characters in log messages
- Removed the use of the locally defined FC transport layer related macros
- Check the rsplen in lpfc_handle_fcp_err function before using rsplen
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following fixes and new features:
- Fix mask size for CT field in WQE
- Fix VPI base not used when unregistering VPI on port 1.
- Fix UNREG_VPI mailbox command to unreg the correct VPI
- Fixed Check for aborted els command
- Fix error when trying to load driver with wrong firmware on FCoE HBA.
- Fix bug with probe_one routines not putting the Scsi_Host back upon error
- Add support for Clear Virtual Link Async Events
- Add support for unsolicited CT exchange sequence abort
- Add 0x0714 OCeXXXXX PCI ID
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following fixes:
- Fixed panic during HBA reset.
- Fixed FCoE event tag passed in resume_rpi.
- Fix out of order ELS commands
- Fixed discovery issues found during VLAN testing.
- Fix UNREG_VPI failure on extended link pull
- Fixed crash while processing unsolicited FC frames.
- Clear retry count in the delayed ELS handler
- Fixed discovery failure during quick link bounce.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some of our virtual SCSI hosts don't have a proper bus parent at the
top, which can be a problem for doing DMA on them
This patch makes the host device cache a pointer to the physical bus
device and provides an extra API for setting it (the normal API picks
it up from the parent). This patch also modifies the qla2xxx and lpfc
vport logic to use the new DMA host setting API.
Acked-By: James Smart <james.smart@emulex.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the duplicated code from FC LLDs to SCSI FC transport class.
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not. It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.
Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation. Update sd_dif and lpfc
accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Ihab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update driver version to 8.3.4
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove spaces before newlines in several log messages
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add bsg (SGIOv4) support for sending and receiving ELS, CT commands
This patch adds a new file, lpfc_bsg.c.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a pair of FCoE issues
- Fix Region 23 FCoE Parameters not being read correctly
- Fix race condition when there are FCoE events during FCF table read
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Consistently implement persistent port disable.
Ability was to be managed in the adapter via firmware via flash settings.
However, not all firmware images supported it. Uniformly support it
everywhere.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Various SLI4 fixes
- Fix switch name not used in the FCF record for FCoE HBAs
- Enabled HBA UE error polling error-condition action code
- Rewrite lpfc_sli4_scmd_to_wqidx_distr() to handle counter rollover cleanly
- Modify resume_rpi mailbox data structure to match current SLI4 spec
- Do not issue mailbox command in MBX_POLL mode when LPFC_HBA_ERROR is set
- Wait for HBA POST completion before checking Online and UE registers
- Fix accumulated total length not being filled in on unsolicited IOCBs
- Use PCI config space register to determine SLI rev of HBA
- Turn on starting ELS tmo function timer during device initialization
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When kzalloc fails in lpfc_hba_alloc, don't dereference the NULL by
lpfc_printf_log. Use dev_err instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-By: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch was originally submitted upstream on 4/21/2008:
http://marc.info/?l=linux-scsi&m=120880973719266&w=2
Somewhere, it never get merged. The patch restructures the task mgmt
routines, commonizing like behavior. Then the patch changes device
reset to LUN resets, and adds a target reset handler.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes:
- Fixed error paths retaking a spin lock which they already hold
- Added code to free memory in a couple of error paths
- Added code to free RPI bit map while unloading driver
- Added code to write zero to memory object allocated through dma_alloc_coherent
- Fixed crash/hang with target or LUN resets
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes:
- Force vport to send LOGO to fabric controller when deleting vport
- Fixed driver failing to register login when a PLOGI is received
- Fixes for FIP discovery
- Added stricter checks for FCF addressing mode
- Added code to send only FLOGI, FDISC and LOGO to Fabric controller as FIP
- Fixed handling of LOGO from Fabric port
- Fixed consecutive link up events skipped link_down processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes
- Set the CT field of FDISC to 3
- Fixed over allocation of SCSI buffers on SLI4
- Removed unused jump table entries
- Increase LPFC_WQE_DEF_COUNT to 256
- Updated FDISC context to VPI
- Fixed immediate SCSI command for LUN reset translation to WQE
- Extended mailbox handling to allow MBX_POLL commands in between async
MBQ commands
- Fixed SID used for FDISC
- Fix crash when accessing ctlregs from sysfs for SLI4 HBAs
- Fix SLI4 firmware version not being saved or displayed correctly
- Expand CQID field in WQE structure to 16 bits
- Fix post header template mailbox command timing out
- Removed FCoE PCI device ID 0x0705
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for persistent vport definitions at creation at boot time
Also includes a few misc fixes for:
- conversion to vpi name from vport slang name
- couple of small mailbox references
- some additional discovery mods
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Changes:
- Convert from SLI2_ACTIVE flag to more correct SLI_ACTIVE (generic) flag
- Reposition log verbose messaging definitions
- Update naming for vpi object name from vport slang name
- Handle deferred error attention condition
- Add 10G link support
- Small bug fixup
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SLI4 supports both FC and FCOE, with some extended topology objects.
This patch adss support for the objects, and updates the disovery
engines for their use.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The mailbox commands themselves are the same, or very similar to
their SLI3 counterparts. This patch genericizes mailbox command
handling and adds support for the new SLI4 mailbox queue.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds support for the new queues in the SLI-4 interface. There are :
- Work Queues - host-to-adapter for fast-path traffic
- Mailbox Queues - host-to-adapter for control (slow-path)
- Buffer Queues - host-to-adapter for posting buffers for async receive
- Completion Queues - adapter-to-host for posting async events,
completions for fast or slow patch work, receipt of async
receive traffic
- Event Queues - tied to MSI-X vectors, binds completion queues with
interrupts
These patches add the all the support code to tie into command submission
and response paths, updates the interrupt handling, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Preps the organization of the driver so that the bottom half, which
interacts with the hardware, can share common code sequences for
attachment, detachment, initialization, teardown, etc with new hardware.
For very common code sections, which become specific to the interface
type, the driver uses an indirect function call. The function is set at
initialization. For less common sections, such as initialization, the
driver looks at the interface type and calls the routines relative to
the interface.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Update driver version to 8.3.1
Also update copyright end year for driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
8.3.1 Fixes/Changes :
- Fix incorrect byte-swapping on word 4 of IOCB (data length) which
caused LUNs to not be discovered on big-endian (e.g. PPC)
- Remove a bad cast of MBslimaddr which loses the __iomem (sparse)
- Make lpfc_debugfs_mask_disc_trc static (sparse)
- Correct misspelled word BlockGuard in lpfc_logmsg.h comment
- Replaced repeated code segment for canceling IOCBs from a list with
a function call, lpfc_sli_cancel_iocbs().
- Increased HBQ buffers to support 40KB SSC sequences.
- Added sysfs interface to update speed and topology parameter without
link bounce.
- Fixed bug with sysfs fc_host WWNs not being updated after changing
the WWNs.
- Check if the active mailbox is NULL in the beginning of the mailbox
timeout handler - fixes panic in the mailbox timeout handler while
running IO stress test
- Fixed system panic in lpfc_pci_remove_one() due to ndlp indirect
reference to phba through vport
- Removed de-reference of scsi device after call to scsi_done() to fix
panic in scsi completion path while accessing scsi device after
scsi_done is called.
- Fixed "Nodelist not empty" message when unloading the driver after
target reboot test
- Added LP2105 HBA model description
- Added code to print all 16 words of unrecognized ASYNC events
- Fixed memory leak in vport create + delete loop
- Added support for handling dual error bit from HBA
- Fixed a driver NULL pointer dereference in lpfc_sli_process_sol_iocb
- Fixed a discovery bug with FC switch reboot in lpfc_setup_disc_node
- Take NULL termintator into account when calculating available buffer space
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix lpfc_parse_bg_err()'s use of do_div(). It should be passing a 64-bit
variable as the first parameter. However, since it's only using a 32-bit
variable, it doesn't need to use do_div() at all, but can instead use the
division operator.
This deals with the following warnings:
CC drivers/scsi/lpfc/lpfc_scsi.o
drivers/scsi/lpfc/lpfc_scsi.c: In function 'lpfc_parse_bg_err':
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: comparison of distinct pointer types lacks a cast
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: right shift count >= width of type
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: passing argument 1 of '__div64_32' from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k1.
[SCSI] qla2xxx: Add ISP81XX support.
[SCSI] qla2xxx: Use proper request/response queues with MQ instantiations.
[SCSI] qla2xxx: Correct MQ-chain information retrieval during a firmware dump.
[SCSI] qla2xxx: Collapse EFT/FCE copy procedures during a firmware dump.
[SCSI] qla2xxx: Don't pollute kernel logs with ZIO/RIO status messages.
[SCSI] qla2xxx: Don't fallback to interrupt-polling during re-initialization with MSI-X enabled.
[SCSI] qla2xxx: Remove support for reading/writing HW-event-log.
[SCSI] cxgb3i: add missing include
[SCSI] scsi_lib: fix DID_RESET status problems
[SCSI] fc transport: restore missing dev_loss_tmo callback to LLDD
[SCSI] aha152x_cs: Fix regression that keeps driver from using shared interrupts
[SCSI] sd: Correctly handle 6-byte commands with DIX
[SCSI] sd: DIF: Fix tagging on platforms with signed char
[SCSI] sd: DIF: Show app tag on error
[SCSI] Fix error handling for DIF/DIX
[SCSI] scsi_lib: don't decrement busy counters when inserting commands
[SCSI] libsas: fix test for negative unsigned and typos
[SCSI] a2091, gvp11: kill warn_unused_result warnings
[SCSI] fusion: Move a dereference below a NULL test
...
Fixed up trivial conflict due to moving the async part of sd_probe
around in the async probes vs using dev_set_name() in naming.
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add SCSI data path, error handling, and debugfs code to complete
BlockGuard support.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update struct definitions, #defines, sysfs entries, and initialization
to support BlockGuard.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix mailbox buffer leak on dump mailbox completion
- Fix mbuf leak in lpfc_pci_probe_one() SLI-2 mode error path
- Don't allocate HBQs in interrupt context
- Use correct size for FCP response buffer so that all available sense
data is copied
- Fix jiffies calculation to prevent crash when collecting statistical
data
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Per the recent discussions at the Linux Plumbers Conference, when
enabling MSI or MSI-X, generate a test interrupt to verify the
interrupt routing is working properly. If the test interrupt fails,
fall back to MSI first, and if that fails as well, to INTx. If the
interrupt test fails with INTx, log an error and fail the PCI probe.
Also changed the use of spin_(lock|unlock) to the _irq(save|restore)
variants in the interrupt handlers because with multi-message MSI-X,
both interrupt handlers can now run in parallel.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Avoid polling HBA Error Attention when HBA's PCI channel is offline
due to PCI EEH
- Fix handling of RSCN with non-zero event qualifiers
- Remove unnecessary sleeps during HBA initialization which slow down
driver load
- Fix internal and external loopback on FCoE HBAs
- Fix incorrect decrement of cmd_pending count in lpfc_queuecomand
error path
- Fix reporting of port busy events to management application
- Rename lpfc_adjust_queue_depth() to lpfc_rampdown_queue_depth() for
consistency with its partner lpfc_rampup_queue_depth()
- Delete redundant lpfc_cmd->start_time = jiffies assignment in
lpfc_queuecommand()
- Fix handling for ELS, mailbox and heartbeat time outs in the worker
thread by removing unnecessary checking of the work_port_events
flags.
- Fix NULL pointer dereference in lpfc_prep_els_iocb
- In lpfc_device_recov_npr_node(), move clearing of NLP_NPR_2B_DISC
flag after call to lpfc_cancel_retry_delay_tmo() to keep
targets-in-discovery count correct
- Remove lpfc_probe_one()'s call to scsi_scan_host() which could cause
concurrent SCSI scans to step on each other
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The phba hbq_get address was setup before the HBA reported support for
Interrupt Enable Block (INB). This caused loopback tests to fail
after all HBQs had been used once. Moved setting of hba_get until
after config port mailbox command completes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Added FC_REG_VPORTRSCN_EVENT to lpfc_nl.h
- Added code to provide option ROM version from HBA and via sysfs
- Added support for HPS bit in config port mailbox command to tell HBA
that host group pointers are in host memory.
- Bugfix for Extended Error Handling (EEH) support on IBM PowerPC P6
platform with MSI enabled
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix lock up on rmmod with vports defined by having
lpfc_pci_remove_one() invoke fc_vport_terminate() to remove all the
vports before invoking fc_remove_host() for the physical port
- Fix echotest failure when NPIV is enabled
- Add the vport_disable function to the physical port's transport
template to make the vport disable attribute visible
- Set the vport state to DISABLE on create if the disable flag is
true
- Call lpfc_alloc_sysfs_attr() for vports so that statistical data
collection works on them
- Support setting a vport's symbolic name via sysfs by writing to
/sys/class/fc_vport/vportX/symbolic_name
- Fix create vport fails when link is down or in loop mode. Should be
able to be create vports any time NPIV is enabled
- Fix slow vport deletes when deleting multiple vports at once
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In the IOCB completion handler, always check if the node is valid
before accessing the node object. Added lpfc_initialize_node() to
initialize nodes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add kernel-doc function headers to lpfc_scsi.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Implement lpfc_pci_suspend_one() and lpfc_pci_resume_one() and
register them in the pci_driver table.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rework RSCN netlink event to send entire RSCN payload
Also replaces (SCSI_NL_VID_TYPE_PCI | PCI_VENDOR_ID_EMULEX) with
LPFC_NL_VENDOR_ID
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for new sysfs attributes: lpfc_stat_data_ctrl and
lpfc_max_scsicmpl_time. The attributes control statistical reporting
of io load.
Added support for new fc vendor events for error reporting.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added new sysfs attribute lpfc_max_scsicmpl_time. Attribute, when enabled,
will control target queue depth based on I/O completion time.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Revert the target busy response in favor of the transport disrupted
response for node state transitions.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for MSI-X Multi-Message interrupts. We use different vectors
for fast-path interrupts (i/o) and slow-patch interrupts (discovery, etc).
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: drop rejecting hunk altered by target busy patches]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for PCI-EEH permanent-disabling a device via lpfc_pci_remove_one()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix the wrong variable name used for checking node active usage status
- Fix numerous duplicate log message numbers
- Fix change KERN_WARNING messages to KERN_INFO.
- Stop sending erroneous LOGO to fabric after vport is already terminated
- Fix HBQ allocates that were kalloc'ing w/ GFP_KERNEL while holding a lock.
- Fix gcc 4.3.2 compiler warnings and a sparse warning
- Fix bugs in handling unsolicited ct event queue
- Reorder some of the initial link up checks, to remove odd VPI states.
- Correct poor VPI handling
- Add debug messages
- Expand Update_CFG mailbox definition
- Fix handling of VPD data offsets
- Reorder loopback flags
- convert to use offsetof()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update driver for new SLI-3 features:
- interrupt enhancements
- lose adapter doorbell writes
- inlining support for FCP_Ixx cmds
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Discovery fixes:
- Fix rejection followed by acceptance in handling RPL and RPS
unsolicited events
- Fix for vport delete crash
- Fix PLOGI vs ADISC race condition
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fc class now calls scsi_target_unblock after calling the
terminate callback, so this patch removes the calls from the
drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We do want to call right back into the queuecommand during the race,
so we can just use SCSI_MLQUEUE_TARGET_BUSY.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update lpfc driver version to 8.2.7
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix bug in mbox sysfs interface that locked in EAGAIN if discovery stalled.
- Fix missing error message when npiv and loop are true when link up occurs.
- Fix panic in lpfc_scsi_cmd_iocb_cmpl: scsi_buf was NULL, but created
race conditions with other code paths.
- Fix error in sysfs mailbox structure that didn't rezero on next use.
- Add missing mempool_free() to attachment failure path
- Fix missing put of ndlp structure during driver unload.
- Fix applications unable to send mailbox commands during discovery.
- Remove unused argument (type) from function lpfc_post_buffer() API
- Fix vport name is not shown after hbacmd vportcreate.
- Remove repeated code statements.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rework of the worker thread to make it more efficient.
Make a finer-grain notfication of pending work so less time is
spent checking conditions. Also made other general cleanups.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix ADISC timeout on initiators causing devloss timeout on targets
- Correct FAN processing : port state vs unreg rpi's wasn't consistent
- Correct mismatches between ASICs and PLOGI that would skip PLOGI
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Prior handler was only waiting for I/O on one lun to finish before
returning completion. Now, wait for all LUNs on the target.
Also performed some rudimentary cleanup while in this code.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
lpfc and qla2xxx overwrite the standard 'state' attribute with
custom callbacks. So rename the custom attributes to 'link_state'
and retain the original meaning of the 'state' attribute.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update lpfc driver version to 8.2.6
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes
- Allow WRITE_VPARAM command when the virtual port is in a stopped state
- Fixed handling of our queue depth max that was unconditionally raising
the depth on all vports, rather than just the vport affected.
- Fix race in interrupt handler for mailbox processing that did not take
out the host lock.
- Removed unused functions: find_node, findnode_rpi, and fabric_abort_flogi
- Correct misspelled word unsolicited in message 0146
- Correct HW-error 5 handling - it should not reset the adapter
- Correct handling of IOCBs, which did not null out our pCmd field before
invoking the midlayer io done function.
- Changed our maximum supported target id to 4096
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
PCI Parity and EEH handling Fixes:
- Under a PCI Data Parity Error, remove a completion routine callback that
was on a command that we had already failed and released.
- Under PCI parity error, we were not reinstalling the interrupt handler
in the slot_reset callback, so we never became functional again.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Multiple Discovery Fixes:
- Fix race on discovery due to link events coinciding with vport_delete.
- Use NLP_FABRIC state to filter out switch-based pseudo initiators that
reuse the same WWNs.
- Correct erroneous setting of DID=0 in lpfc_matchdid()
- Correct extra reference count that was in the lookup path for the
remoteid from an unsolicited ELS.
- Correct double-free bug in els abort path.
- Correct FDMI server discovery logic for switch that return a WWN of 0.
- Fix bugs in ndlp mgmt when a node changes address
- Correct bug that did not delete RSCNs for vports upon link transitions
- Fix "0216 Link event during NS query" error which pops up when vports
are swapped to different switch ports.
- Add sanity checks on ndlp structures
- Fix devloss log message to dump WWN correctly
- Hold off mgmt commands that were interferring with discovery mailbox cmds
- Remove unnecessary FC_ESTABLISH_LINK logic.
- Correct some race conditions in the worker thread, resulting in devloss:
- Clear the work_port_events field before handling the work port events
- Clear the deferred ring event before handling a deferred ring event
- Hold the hba lock when waking up the work thread
- Send an acc for the rscn even when we aren't going to handle it
- Fix locking behavior that was not properly protecting the ACTIVE flag,
thus allowing mailbox command order to shift.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 3163f725a5 introduced locking in
lpfc_sli_hbqbuf_fill_hbqs, but missed unlocking on one exit.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global lpfc_disable_node() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update lpfc driver version to 8.2.5
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous fixes:
- Fix ERRATT flag which was overlapping
- Allow RESTART mbx commands through when stopped.
- Accept incoming PLOGI when connected to an N_Port.
- Fix NPort to NPort pt2pt problems: ADISC and reg_vpi issues
- Fix vport unloading error that erroneously cleaned up RSCN buffers
- Fix memory leak during repeated unloads - in mbox handling
- Fix link bounce vs FLOGI race conditions
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct ndlp referencing issues:
- Fix ndlp kref issues due to race conditions between threads
- Fix cancel els delay retry event which missed an ndlp reference count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Based on a patch from Ingo Molnar <mingo@elte.hu> as he pointed out that
I wrongly missed this.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update lpfc driver version to 8.2.4
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rework misplaced reference taking on node structure
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Enhance debugfs to dump HBA SLIM as well as Host SLIM
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix Drivers Unsolicited CT command handling - we did not handle multiframe
sequences well.
Fix error due to delay in replenishing buffers for unsolicited data.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Made link speed and link topology modifiable via sysfs
Make scatter gather Segment Count into a module parameter.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is a patch written by Tomohiro Kusumi and submitted to
linux-scsi:
http://marc.info/?l=linux-scsi&m=118673720712152&w=2
The original patch comment:
This patch makes Emulex lpfc driver legacy I/O port free.
It has already been acked quite long time ago.
So I resubmit the patch.
http://lkml.org/lkml/2006/11/22/28
Current lpfc driver is already using pci_select_bars()
and pci_enable_device_bars() when the PCI bus has been reset.
So I think this patch should also be acked.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix a couple of sparse complaints
- Reset the FCP recovery flag when the node is not a FCP2 device.
- Speed up offline prep delays
- Fixed a memory leak in lpfc_mem_alloc failure path
- Fixed external loopback test.
- Fixed error code returned from the driver when HBA is over heated.
- Correct Max NPIV vport to limits read from adapter
- Add missing locks around fc_flag and FC_NEEDS_REG_VPI
- Add missing hba ids for device identification
- Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands
- Changed all temperature event messages from warning to error
- Fix reporting of link speed when link is down
- Added support for MBX_WRITE_WWN mailbox command
- Change del_timer_sync() in ISR to del_timer() in interrupt handler
- Correct instances of beXX_to_cpu() that should be cpu_to_beXX()
- Perform target flush before releasing node references on module unload
- Avoid bogus devloss_tmo messages when driver unloads
- Fix panic when HBA generates ERATT interupt
- Fix mbox race condition and a workaround on back-to-back mailbox commands
- Force NPIV off for pt2pt mode between 2 NPorts
- Stop worker thread before removing fc_host.
- Fix up discovery timeout error case due to missing clear_la
- Tighten mailbox polling code to speed up detection of fast completions
- Only allow DUMP_MEMORY if adapter offline due to overtemp errors
- Added extended error information to the log messages in chip init.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add parameters to enable and disable heartbeat and hba resets
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct Abort handler logic. It was unconditionally waiting a minimum
of 2 seconds rather than looking for abort completion.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Discovery/ELS Fixes:
- Delay free's of ELS requests if adapter reject conditions
- Fix concurrent PLOGI vs ADISC state handling
- Add retry mechanism for GFF_ID
- Correct some illegal state transitions around RSCN timeouts
- Fix missing return in FAN handling
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Change version number to 8.2.3
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Temperature handling fix - return proper error code indicator for applications
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Internal loopback fixes:
- Use HBQs rather than Q_RING_BUFF
- Correct HBQs continuation entries
- Update CT handler to SLI3 iocbs
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Small Fixes - part 2
- Fix ndlp left in PLOGI state after link up
- Fix cannot rcv unsol ELS frames after running HBA resets for a few minutes
- Fix HBQ buffer_count implemention
- Fix RPI leak
- Fix crash while deleting vports while HBA is reset
- Revert the FCP Fbits offset back to 7
- Fix panic when deleting vports
- Remove unused code in switch statement outside of a case
- Reject PLOGI from invalid PName or NName of 0
- Ignore PLOGI responses from WWPName or WWNName of 0
- Fix debugfs hbqinfo display for ppc
- Added 8G to list of supported speeds for sysfs parameter
- Defer ndlp cleanup to dev-loss timeout handler
- Added support for WRITE_VPARMS mailbox command by applications
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FC Discovery Fixes:
- Fix up lpfc_drop_node() vs lpfc_nlp_not_used() usage
- Clear ADISC flag when unregistering RPI and REMOVE ndlps if in recovery.
- Fix usage of UNUSED list and ndlps
- Fix PLOGI race conditions
- Reset link if NameServer PLOGI errors occur
- Synchronize GID_FT queries with PLOGI receptions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Small Fixes - part 1
- Fix typo kmzlloc -> kzalloc
- Fix discovery ndlp use after free panic
- Fix link event causing flood of 0108 messages
- Relieve some mbox congestion on link up with 100 vports
- Fix broken vport parameters
- Prevent lock recursion in logo_reglogin_issue
- Split uses of error variable in lpfc_pci_probe_one into retval and error
- Remove completion code related to dev_loss_tmo
- Remove unused LPFC_MAX_HBQ #define
- Don't compare pointers to 0 for sparse
- Make 2 functions static for sparse
- Fix default rpi cleanup code causing rogue ndlps to remain on the NPR list
- Remove annoying ELS messages when driver is unloaded
- Fix Cannot issue Register Fabric login problems on link up
- Remove LPFC_EVT_DEV_LOSS_DELAY
- Fix FC port swap test leads to device going offline
- Fix vport CT flags to only be set when accepted
- Add code to handle signals during vport_create
- Fix too many retries in FC-AL mode
- Pull lpfc_port_link_failure out of lpfc_linkdown_port
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
NPIV bug fixes:
- Remove vport params on physical hba when npiv is disabled
- Implement new DA_ID CT command to remove vport information from
the switch after delete. Some switches didn't clean this up unless
the physical link dropped.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for ASICs that report temperature. Temperature notices are
reported as events and logged. Temperature can be read via sysfs.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch corrects the lpfc tag handling issue identified by Hannes Reinecke
http://marc.info/?l=linux-scsi@m=119270235628850&w=2
The basis for this patch originated from Hajime Kai. Thank You Hajime.
Signed-off-by: hajime-kai@soft.fujitsu.com
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a typo introduced by
commit bbfbbbc118.
It wasn't a compile error since CONFIG_LPFC_DEBUG_FS is not (yet?)
available as an option.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The Coverity checker noticed that we may overrun a statically allocated
array in drivers/scsi/lpfc/lpfc_sli.c::lpfc_sli_hbqbuf_find().
The case is this; In 'struct lpfc_hba' we have
#define LPFC_MAX_HBQS 4
...
struct lpfc_hba {
...
struct hbq_s hbqs[LPFC_MAX_HBQS];
...
};
But then in lpfc_sli_hbqbuf_find() we have this code
hbqno = tag >> 16;
if (hbqno > LPFC_MAX_HBQS)
return NULL;
if 'hbqno' ends up as exactely 4, then we won't return, and then this
list_for_each_entry(d_buf, &phba->hbqs[hbqno].hbq_buffer_list, list) {
will cause an overflow of the statically allocated array at index 4,
since the valid indices are only 0-3.
I propose this patch, that simply changes the 'hbqno > LPFC_MAX_HBQS'
into 'hbqno >= LPFC_MAX_HBQS' as a possible fix.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was pointed out by Boaz Harrosh <bharrosh@panasas.com> that our
8.2.2 lpfc patches revert a change to using SCSI command accessor
functions.
This patch, to be applied on top of the 8.2.2. patches, updates the
driver for the accessor functions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Clean up all instances of mixed tab-space indentation
- Clean up sparse build errors
- Add appropriate static's
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Fix vport ndlp ref counting errors
- Fix use after free of ndlp structure
- Use the correct flag to check for LOADING setting.
- Fix driver unload bugs (related to shost references) after link down or rscn
- Fix up HBQ initialization
- Fix port_list locking around driver unload.
- Fix references to hostdata as a phba
- Fix GFFID type offset to work correctly with big endian structure.
- Only call pci_disable_msi if the pci_enable_msi succeeded
- Fix vport_delete wait/fail if in discovery
- Put a reference on the nameservers ndlp when performing CT traffic.
- Remove unbalanced hba unlock.
- Fix up HBQ processing
- Fix lpfc debugfs discovery trace output for ELS rsp cmpl
- Send ADISC when rpi is 0
- Stop FDISC retrying forever
- Unable to retrieve correct config parameter for vport
- Fix sli_validate_fcp_iocb, sli_sum_iocb, sli_abort_iocb to be vport-aware.
- Fix index-out-of-range error in iocb. Spotted by Coverity.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Remove the "management_version" sysfs parameter (was unused)
- Add HBQ information to lpfc debugfs
- Change lpfc_npiv_enable name back to lpfc_enable_npiv (internal stds)
- Remove "issue_lip" attribute from the vports transport template
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rework the lpfc_printf_log() macro so that logging is enabled on a
per-vport basis. Used to be on a physical-port basis, thus logging
with large numbers of vports became a mess. Required redefinition of
the macro, and an update of every use.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Split attributes up into vport and non-vport attributes.
- Move vport specific cfg params to vport
Many of the vport-specific behaviors were still global attributes
on the physical port. Move them to the vport itself.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleans up a lot of bad behaviors that have been in this area a while
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Error messages and debugfs updates:
- Fix up GID_FT error messages
- Enhance debugfs with slow_ring_trace, dumpslim and nodelist information
- Add log type (and messages) for vport state changes
- Enhance log messages when retries ELS fail
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_create_port':
drivers/scsi/lpfc/lpfc_init.c:1573: error: 'struct kobject' has no member named 'dentry'
Just remove the if check on this ... lpfc shouldn't be poking around
in kobject structures.
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_pci_probe_one':
drivers/scsi/lpfc/lpfc_init.c:1723: warning: unused variable 'retval'
And remove the unused variable.
Cc: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch uses dma_map_sg with phba->pcidev->dev instead of
scsi_dma_map.
scsi_dma_map doesn't work for NPIV since fc_vport->dev isn't fully
initialized. check_addr() in arch/x86_64/kernel/pci-nommu.c leads to
the crash since dev->dma_mask is NULL.
For more details:
http://marc.info/?l=linux-scsi&m=118312448030633&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is an addendum to:
commit a0b4f78f9a
Author: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[SCSI] lpfc: convert to use the data buffer accessors
One place was missed in the merge
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As suggested by Andrew, add pci_try_set_mwi(), which does not require
return-value checking.
- add pci_try_set_mwi() without __must_check
- make it return 0 on success, errno if the "try" failed or error
- review callers
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the driver version to 8.2.1
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is a reworked version of the data buffer accessors patch
so that it applies on the NPIV sources.
The original patch was developed and submitted by Fujita Tomonori:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
http://marc.info/?l=linux-scsi&m=117896446832171&w=2
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the NPIV support, the following changes have been accumulated
in the testing and qualification of the driver:
- Fix affinity of ELS ring to slow/deferred event processing
- Fix Ring attention masks
- Defer dev_loss_tmo timeout handling to worker thread
- Consolidate link down error classification for better error checking
- Remove unused/deprecated nlp_initiator_tmr timer
- Fix for async scan - move adapter init code back into pci_probe_one
context. Fix async scan interfaces.
- Expand validation of ability to create vports
- Extract VPI resource cnt from firmware
- Tuning of Login/Reject policies to better deal with overwhelmned targets
- Misc ELS and discovery fixes
- Export the npiv_enable attribute to sysfs
- Mailbox handling fix
- Add debugfs support
- A few other small misc fixes:
- wrong return values, double-frees, bad locking
- Added adapter failure heartbeat
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is added to the driver. It utilizes the interfaces of
the fc transport for the creation and deletion of vports. Within the
driver, a new Scsi_Host is created for each NPIV instance, and is
paired with a new instance of a FC port. This allows N FC Port
elements to share a single Adapter.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is only available via new adapter interface extensions,
termed SLI-3. This interface changes some of the basic behaviors such
as command and response ring element sizes and data structures, as
well as a change in buffer posting. Note: the new firmware extensions
are found only on our mid-range and enterprise 4Gig adapters - so NPIV
support is available only on these newer adapters. The latest firmware
can be downloaded from the Emulex support page.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is reorganized to separate the handling of the adapter from
the handling of the FC port. Adapter handling includes submissions of
command requests, receiving responses, and managing adapter resources.
The FC port includes the discovery engine, login handling, and the
mapping of a Scsi_Host on the "port". Although not a large functional
change, as it touches core structures and functions, resulting in a
large text delta.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added support for 8G speed and new HBAs.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for async scanning
Notes: This is the async scan patch to our driver from Matthew Wilcox.
The async scan logic is still subject to errors in insmod/rmmod, as
the async scan threads don't get shutdown when the module unloads
underneath them. See http://marc.info/?l=linux-scsi&m=117551999925582&w=2
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't process ERATT interrupts when issuing KILL_BOARD mbx command
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Collapse discovery lists to a single node list.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve handling of failed ELS aborts.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve diagnostic messages and change local loopback message to KERN_INFO
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed recovery of rport after race with dev_loss_tmo
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Round 2 of Miscellaneous fixes:
- Ensure we don't prematurely re-enable IRQs in lpfc_sli_abort_fcp_cmpl().
- Prevent freeing of iocb after IOCB_TIMEDOUT error.
- Added code to cleanup REG_LOGIN mailbox command when a LOGO is received.
- Fix offline window where more work can sneak in after clearing work_ha
- Use target reset instead of LU reset in bus_device_reset_handler
- Fixed system hangs due to leaked host_lock.
- Fixed NULL pointer dereference during I/O with LIP.
- Fixed false iocb timeout.
- Fixed name server query response handling.
- Change rport dev_loss_tmo value when user change lpfc HBA's dev_loss_tmo.
- Fixed a memory leak in lpfc_sli_wake_mbox_wait.
- Fixed check for dropped frames.
- Removed hba queue depth calculation based on device PCI IDs
- Change min cr_count value specified in comment to agree with setting
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reorganize lpfc_nlp_list() and callers to prepare for nodelist simplification.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modify ELS abort handling to prevent double completion
Rework portions of ELS abort handling to prevent double completion
- Rework ELS iotags and correct abort routine
- Move the (badly wrong) ELS completion logic from the initial ELS
abort request function to the ELS completion function.
- Fixup the iocb completion handling to account for the ELS abort
completions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc bug fixes and code cleanup:
- Fix system hang while running on systems with IOMMU
- Fix use after free issues with rports
- Don't free mailbox structure if it's still on the mboxq list
- Decrement txq_cnt rather than txcmplq_cnt when parsing the txq list
- Use msleep for long delays to prevent soft lockup bug check
- Don't remove node during dev_loss_tmo if discovery is active
- Fix memory leaks in get/reset statistics and link attention paths
- Fixed lpfc_ns_rsp to handle entire GID_FT response.
- mbox interface should use MAILBOX_CMD_SIZE rather than sizeof(MAILBOX_t)
- Fixed bug check in add_timer.
- Fixup messages 0116, 0117, and 0128 to report ELS I/O tag.
- Remove unused parameter to lpfc_cleanup.
- Change mailbox timeout handling.
- Remove unused buflist. Code cleanup.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have seen two cases where VPD on an emulex card has been incorrect
and we end up walking off the end of memory. It looks like someone made
an update (increased the length of a string) without increasing the
Length field. Then we do:
Length -= (3+i);
And since Length is unsigned it becomes very large and we loop forever
in the encapsulating:
while (Length > 0) {
If we make Length signed then we fall out of the loop and proceed on.
Its important to note we have only seen this in the lab and it may be
the only two cases of this in existence, but since the rest of the code
has been written to be resilient against bad VPD we may as well fix this
too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a PCI error is detected that cannot be recovered from, there
will be a double call of lpfc_pci_remove_one(), with the second call
resulting in a null-pointer dereference. The first call occurs in
lpfc_io_error_detected(), and the second call during pci device
remove. This patch eliminates the first call; its un-needed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds PCI Error recovery support to the
Emulex Lightpulse Fibrechannel (lpfc) SCSI device driver.
Lightly tested at this point, works.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Bino.Sebastian@Emulex.Com
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add kmalloc failure check and fix the loop on error path. Without the
patch pool element at index [0] will not be freed.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Fixes:
- Prevent references to NULL node list element in reset routines.
- Add missing IOCB types to switch tables
- Reset the card on Port Error 5
- Fix infinite loop in LUN reset
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver now allows both wwpn and wwnn to be set.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To avoid continually updating the driver for new subsystem ids
(as adapter modules are proliferating), remove this 2nd level decode.
Genericize the reported Adapter names to be consistent across
Emulex product line.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add MSI (Message Signalled Interrupts) support
Actual use must be enabled via the new module parameter "lpfc_use_msi"
Defaults to no use
Many thanks to Frederic Temporelli who implemented the initial patch.
Signed-off-by: Frederic Temporelli <frederic.temporelli@ext.bull.net>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adjust LOG_FCP logging to be more meaningful.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was not accounted for in the fast/slow rings.
Genericize the implementation and control it via sysfs
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Discovery Fixes:
- Prevent starting discovery of a node if discovery is in progress.
- Code improvement (reduction) for lpfc_findnode_did().
- Update discovery to send RFF to Fabric on link up
- Bypass unique WWN checks for fabric addresses
- Add ndlp to plogi list prior to issuing the plogi els command
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix printk format warning:
drivers/scsi/lpfc/lpfc_attr.c:597: warning: long long unsigned int format, uint64_t arg (arg 4)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we fail to allocate mp->virt during the first while loop iteration,
mlist is still uninitialized, therefore we should check if before
dereferencing.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for a new lpfc soft_wwpn sysfs attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for new dev_loss_tmo callback
Goodness is that it removes code for a parallel nodev timer that
existed in the driver
Add support for the new fast_io_fail callback
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to return adapter symbolic name (now that attribute is dynamic)
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to post events via new FC event interfaces
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Stall error handler if attempting resets/aborts while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Background:
Although the transport is using the scsi_timed_out functionality to
restart the timeout if the rport is blocked, if the timeout has already
fired before the block occurs, the eh handler still runs and can take
the device offline. Ultimately, this window cannot be resolved without
significant work in the error handler thread. Christoph noted the first
level of these issues when he noted the poor error response handling
by the error thread.
We found, under heavy load and error testing, that time window from when
the scsi_times_out() adds the io to the queue to when the scsi_error_handler
gets around to servicing it, can be in the several seconds range. In most
cases, these test conditions are highly unusual, but possible.
As a result, we're stalling the error handler in this race window so that
we can avoid the device_offline transitions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Bug Fixes:
- Cap MBX_DOWN_LINK command timeout to 60 seconds
- Fix double free of ndlp object
- Don't free mbox structures on error. The completion handlers expect to do so.
- Clear host attention work items when going offline
- Fixed discovery issues in multi-initiator environments.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ID String and Message fixes
- Fix switch symbolic name registration to match cross-OS values
- Replace printk's with more standard lpfc_printf_log calls
- Make all lpfc_printf_log message numbers unique
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Short bug fixes:
- Fix iocbq list corruption due to missing list_del's in ct handling
- Missing unlock in lpfc_sli_next_iotag()
- Fix initialization of can_queue value
- Differentiate sysfs mailbox errors with different codes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix race condition between lpfc_sli_issue_mbox and lpfc_online
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix failing firmware download due to mailbox delays needing to be longer.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Fixes:
- Fix some sparse warnings - casts of address space
- Fix handling of the adapter registration string. Each invocation
was byteswapping, so every other adapter init attempt failed.
- Correct comments and default value for the lpfc_max_luns parameter
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add lpfc_sli_flush_mbox_queue() function and use it in lpfc_offline() call
to avoid deadlock on thread block.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct the wait in attachment that delays for topology discovery
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove depricated sysfs attribute board_online, as it's replaced by the new
issue_reset attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding new issue_reset sysfs attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic in lpfc_sli_validate_fcp_iocb due to access of scsi_cmnd after
returning it to the midlayer
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Consolidate dma buf cleanup into a separate function
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct bogus nodev_tmo message on NPort that changes its NPort Id
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix txcmplq related panics on heavy IO while downloading firmware
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Issue DOWN_LINK prior to INIT_LINK to work around link failure issue
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed infinite retry of REG_LOGIN mailbox failed due to MBXERR_RPI_FULL
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix memory leak and cleanup code related to per ring lookup array.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Standardize the driver on a single define for the maximum supported targets.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use mod_timer instead of add_timer in lpfc_els_timeout_handler
This patch was formerly posted by Mark Haverkamp.
http://marc.theaimsgroup.com/?l=linux-scsi&m=114246089015681&w=2
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes the duplicate functionality which had been added to
the lpfc driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix sparse warnings: use NULL instead of 0 for pointers:
drivers/scsi/lpfc/lpfc_els.c:827:56: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2781:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2782:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:951:21: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:956:20: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the lpfc driver to revision 8.1.6, which includes
the following changes:
- Fix data corruption in SCSI BUS reset path, due to reusing
the same request structure for each target.
- Change version number to 8.1.6
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Contains the following misc fixes:
- Fix build warnings
- Race condition in lpfc_workq_post_event() could corrupt phba->work_list.
- nlp_sid was not being initialized properly
- Fix some RSCN handling during the re-discovery after Link Up event.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Additional fixes to LOGO, PLOGI, and RSCN processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix cleanup code in the lpfc_pci_probe_one() error code path.
This changes the original patch by:
- hardsetting the return value from lpfc_pci_probe_one() to
-ENODEV (negative value) if we fail attach
- removes the checks from lpfc_pci_remove_one() validating the
host and phba pointers as it's no longer needed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed FC protocol violation in handling of PRLO.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use asynchronous ABTS completion to speed up abort completions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix Discovery processing for NPorts that hit nodev_tmo during discovery
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch changes several mempool users, all of which are basically just
wrappers around kmalloc(), to use the common mempool_kmalloc/kfree, rather
than their own wrapper function, removing a bunch of duplicated code.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two misc fixes:
- Fix deadlock caused by return with host_lock held in lpfc_findnode_did
- Initialize all fields of the allocated mail box structure to zero.
Was causing some sysfs mailbox commands to fail immediately after load.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce lpfc_reset_barrier() function for resets on dual channel adapters
Workaround for a hardware errata on dual channel asics. There is a
potential for the chip to lock up on a reset if a shared dma engine is in
use. The (ugly) work around requires a reset process which uses a mailbox
command to synchronize the independent channels prior to the reset to
avoid the issue. Unfortunately, the timing windows required to ensure this
workaround succeeds are very specific, meaning we can't release the cpu
during the barrier.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed a timer panic due to timer firing after freeing ndlp
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed RSCN handling when a PLOGI is in retry.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
