The Freescale PCI-e controllers have an issue in that they use the
PCI_PRIMARY_BUS register in the virtual P2P bridge to determine which
bus number to match on when generating a type 0 config cycle. The
issue is if we are renumbering bus numbers to match Linux we will try
setting the PCI_PRIMARY_BUS and will not know which bus number to use
for generating type 0 config cycles. We surpress writing the register
in the P2P bridge and always keep it at zero.
In the future when proper PCI domain support is working we should be
able to remove this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We check the Link Training and State Status register to make sure we
are at least at the L0 state.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The generic PCI config ops indirect support for ppc32 covers only two
cases (implicit vs explicit) type 0/1 config cycles via set_cfg_type.
Added a indirect_type bit mask to handle other variants.
Added support for PCI-e extended registers and moved the cfg_type
handling into the bit mask for ARCH=powerpc. We can also use this to
handle indirect quirks.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds device nodes for the PCI bridges as well as the ISA devices on
the newer revision MPC8641HPCN. It also adds the PCI ranges to the soc
node so that address translation for the ISA devices works properly.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove errata for PCI-e support of Rev 1.0 of MPC8641 since its considered
obselete and is not production level silicon from Freescale.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added self_busno to pci_controller and indirect PCI ops to be set by
board code to indicate which bus number to use when talking to the PHB.
By default we use zero since the majority of controllers that have
implicit mechanisms to talk to the PHBs use a bus number of zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user of the fsl_pcie code doesn't set bus_offset and 82xx doesn't
require it either. Remove the places in the code that reference it so
we can remove it all together.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have the pci_controller in the exclude function we can easy
figure out if the bus number is the PHB or not. The old style of using a
variable setup at init time was actually broken and would only work in
specific cases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The hose->bus_offset is only used for PCI config cycles and the 52xx PCI
config code doesn't actually ever set bus_offset to a non-zero value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles. They handle producing them by implicitly looking at the
bus, devfn.
The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The TSI108 code and the 32 bit powermac and chrp platforms
have dependency on PCI that is not easy or desirable to get rid
of.
The easiest fix is to always select CONFIG_PCI if one of those
platforms is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.
The easiest fix is to just remove all these definitions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cores used in the MPC82xx/83xx/86xx embedded controllers are very similar
to those in the 32 bit general-purpose processors, so it makes sense to
treat them as the same CPU family.
Choosing between the embedded platforms and the multiplatform code is
now done in the platform menu, but functionally everything stays the
same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A strict reading of the flattened device tree format defined in
booting-without-of.txt does in fact require that all the tags defining
properties for a node go before any definitions of subnodes, however
it's not particularly emphasised. Although allowing intermingled
properties and subnodes would not be ambiguous in meaning, the kernel
parser does currently require that properties precede subnodes.
Furthermore, keeping this constraint makes life easier for various
device tree scanning tools.
Therefore, re-emphasise in booting-without-of.txt that this is a
strict requirement of the flattened device tree format.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-powerpc/processor.h declares, and arch/ppc/platforms/prep_setup.c
defines variables ucBoardRev, ucBoardRevMaj and ucBoardRevMin which
are used nowhere in the current kernel (neither in arch/ppc nor
arch/powerpc). This removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 2e60161337 split up
arch/powerpc/boot/of.c so that some OF functions can be used on
platforms that don't want to use the overall OF platform boot code.
This is useful on things like PReP which can have an OF implementation
which is useful for debugging output, but inadequate for booting.
However, that commit didn't export quite enough things to make a
usable OF console on a non-OF system. In particular, the device tree
manipulation performed to initialize the OF console code must
explicitly use the OF device tree, rather than the flattened device
tree, even if the system is otherwise booting using a flattened device
tree. This makes it so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 3d5134ee83 left debugging turned on
in arch/powerpc/kernel/pci_64.c. This turns it off again.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently iSeries will recalibrate the cputime_factors in the first
settimeofday() call.
It seems the reason for doing this is to ensure a resaonable time delta after
time_init(). On current kernels (with udev), this call is made 40-60 seconds
into the boot process, by moving it to a late initcall it is called
approximately 5 seconds after time_init() is called. This is sufficient to
recalibrate the timebase.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for storage devices to the device probe code.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add storage driver core support for the PS3.
PS3 storage devices are a special kind of PS3 system bus device.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Preallocate 256 KiB of bootmem memory for the PS3 FLASH ROM storage driver.
This can be disabled by passing `ps3flash=off' on the kernel command line.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PS3 uses the kernel's hotplug memory support, so make sure it is
always enabled when building for PS3.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For the convenience of custom platform code make the powerpc
bootwrapper typdef kernel_entry_t global in scope.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes the constantness of the powerpc bootwrapper's console_ops.write
routine. Allows printing of constant strings.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for the 'll' (long long) printf qualifier in the powerpc zImage
bootwrapper. This is useful for bootwrapper debugging on 64 bit platforms.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add signed types to the powerpc zImage bootwrapper. These are needed by the
PS3 hcall interface.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove references to pSeries and OpenFirmware in the __secondary_hold
usage comment. __secondary_hold is a generic routine and can be used
by other platforms.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a printout of the params value to early_init_devtree.
This value is handy to have for comparison when debugging the
bootwrapper code.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace the inline asm with bitops in the PS3 interrupt
chip mask routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the PS3 static symbols node to ppe_id and cpu to thread_id
to clarify usage.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add routines to probe devices present on the system
and to register those devices with the LDM.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the ps3fb device from a platform device to a PS3 system bus device.
Fix the remove and shutdown methods to support kexec and to make ps3fb a
loadable module.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the PS3 ps3av driver a loadable module.
- Replace static data with kmalloc()'ed.
o Allocate struct ps3av dynamically, as it contains data used as vuart
receive/transmit buffers
o Move static recv_buf from ps3av_do_pkt() to struct ps3av
- Move ps3av_vuart_{read,write}() from drivers/ps3/ps3av_cmd.c to
drivers/ps3/ps3av.c and make them static as they're used in that file only.
- Make device a PS3 system-bus device.
- Update copyright formatting.
- Make two new routines ps3av_register_flip_ctl() and ps3av_flip_ctl() to
support late binding of the frame buffer flip control routine.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 sys-manager updates to reflect the new PS3 unifed device support.
Fixups to the PS3 sys-manager driver to properly support sys_reboot().
- Add varable request_tag to struct ps3_sys_manager_header.
- Move ctrl_alt_del from PS3_SM_EVENT_POWER_RELEASED to
PS3_SM_EVENT_POWER_PRESSED.
- Make the PS3 sys-manager driver a loadable module.
- Add new file sys-manager-core.c.
- Add new struct ps3_sys_manager_ops for dynamic binding.
- Put data sent to device on stack.
- Add support for PS3_SM_SERVICE_ID_REQUEST_ERROR.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 vuart updates to reflect the new PS3 unified device support.
- Move vuart devices to the PS3 system bus.
- Replace use of ps3_vuart_port_device with ps3_system_bus_device.
- Make the PS3 vuart bus driver a loadable module.
- Add remove() and shutdown() routines.
- Move ps3_vuart_work into ps3_vuart_port_priv.tx_list.
- Remove redundant spinlock ps3_vuart_work.lock.
- No longer free ps3_vuart_port_device.priv on shutdown.
- Cleanup Kconfig defs.
- Export symbols needed for modular port drivers.
- Arrange to use port numbers found in repository.
- Fix bugs in ps3_vuart_read_async() and polled reading
- Cleanup handling of shared interrupt with ps3_vuart_bus_interrupt_get()
and ps3_vuart_bus_interrupt_put()
- Add more comments to vuart.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Repository updates:
- Extract ps3_repository_find_bus() from ps3_repository_find_device(), as the
storage driver needs it.
- Make ps3_repository_find_device() return -ENODEV if a device is not found,
just like if a bus is not found.
- Add ps3_repository_read_vuart_sysmgr_port() and
ps3_repository_read_vuart_av_port() to get vuart port info.
- Add device enumeration routines ps3_repository_find_device() and
ps3_repository_find_devices().
- Cleanup debug routines.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add modinfo attribute to ps3_system_bus devices. Also make them all
children of the same ps3_system_bus 'device' so they appear in a
corresponding subdirectory under /sys/devices.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow userspace to automatically load modules, we need to hook up
uevent for ps3_system_bus devices. I've used the form 'ps3:%d' with
the ps3_match_id, since that's what we use for matching drivers.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework the PS3 system bus to unify device support.
- DMA region sizes must be a power of two
- storage bus DMA updates:
- Small fixes for the PS3 DMA core:
o fix alignment bug
o kill superfluous test
o indentation
o spelling
o export ps3_dma_region_{create,free}()
- ps3_dma_region_init():
o Add `addr' and `len' parameters, so you can create a DMA region that
does not cover all memory (use `NULL' and `0' to cover all memory).
This is needed because there are not sufficient IOMMU resources to have
all DMA regions cover all memory.
o Uninline
- Added remove and shutdown routines to all drivers.
- Added loadable module support to all drivers.
- Added HV calls for iopte management (needed by sound driver).
Signed-off-by: MOKUNO Masakazu <mokuno@sm.sony.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixup the core platform parts needed for kexec to work on the PS3.
- Setup ps3_hpte_clear correctly.
- Mask interrupts on irq removal.
- Release all hypervisor resources.
- Create new routine ps3_shutdown_IRQ()
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This just moves the definitions of the PS3 chip_mask routines up
above the irq setup routines. This change is needed for the
kexec updates that follow. Also adds some inline documentation
to the routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
