The ARM big LITTLE cpufreq driver uses the OPP layer for its
functionality. Select it in Kconfig.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For arm S5pv210 with allmodconfig, ARM_S5PV210_CPUFREQ need
CONFIG_CPU_FREQ_TABLE=y, or will cause compiling issue.
The related operation:
+ arm-linux-gnu-ld -EL -p --no-undefined -X --build-id -X -o .tmp_vmlinux1 -T /root/linux-next/arch/arm/kernel/vmlinux.lds arch/arm/kernel/head.o init/built-in.o --start-group usr/built-in.o arch/arm/nwfpe/built-in.o arch/arm/vfp/built-in.o arch/arm/kernel/built-in.o arch/arm/mm/built-in.o arch/arm/common/built-in.o arch/arm/net/built-in.o arch/arm/crypto/built-in.o arch/arm/mach-s5pv210/built-in.o arch/arm/plat-samsung/built-in.o kernel/built-in.o mm/built-in.o fs/built-in.o ipc/built-in.o security/built-in.o crypto/built-in.o block/built-in.o arch/arm/lib/lib.a lib/lib.a arch/arm/lib/built-in.o lib/built-in.o drivers/built-in.o sound/built-in.o firmware/built-in.o net/built-in.o --end-group
The related errors:
drivers/built-in.o: In function `s5pv210_target':
drivers/cpufreq/s5pv210-cpufreq.c:225: undefined reference to `cpufreq_frequency_table_target'
drivers/cpufreq/s5pv210-cpufreq.c:237: undefined reference to `cpufreq_frequency_table_target'
drivers/built-in.o: In function `s5pv210_verify_speed':
drivers/cpufreq/s5pv210-cpufreq.c:182: undefined reference to `cpufreq_frequency_table_verify'
drivers/built-in.o: In function `s5pv210_cpu_init':
drivers/cpufreq/s5pv210-cpufreq.c:556: undefined reference to `cpufreq_frequency_table_get_attr'
drivers/cpufreq/s5pv210-cpufreq.c:560: undefined reference to `cpufreq_frequency_table_cpuinfo'
make: *** [vmlinux] Error 1
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds dvfs support for exynos5440 SOC. This soc has 4 cores and
they scale at same frequency. The nature of exynos5440 clock controller is
different from previous exynos controllers so not using the common exynos
cpufreq framework. The major difference being interrupt notification for
frequency change. Also, OPP library is used for device tree parsing to get
different parameters like frequency, voltage etc. Since the opp library sorts
the frequency table in ascending order so they are again re-arranged in
descending order. This will have one-to-one mapping with the clock controller
state management logic.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves cpufreq driver of ARM based sa11x0 platform to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves cpufreq driver of ARM based integrator platform to
drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Normally we keep drivers in alphabetical inside Kconfig and Makefile and over
time this was broken for ARM cpufreq drivers. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
big LITTLE is ARM's new Architecture focussing power/performance needs of modern
world. More information about big LITTLE can be found here:
http://www.arm.com/products/processors/technologies/biglittleprocessing.phphttp://lwn.net/Articles/481055/
In order to keep cpufreq support for all big LITTLE platforms simple/generic,
this patch tries to add a generic cpufreq driver layer for all big LITTLE
platforms.
The driver is divided into two parts:
- Core driver: Generic and shared across all big LITTLE SoC's
- Glue drivers: Per platform drivers providing ops to the core driver
This patch adds in a generic glue driver which would extract information from
Device Tree.
Future SoC's can either reuse the DT glue or write their own depending on the
need.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
The Marvell Kirkwood SoCs have simple cpufreq support in hardware. The
CPU can either use the a high speed cpu clock, or the slower DDR
clock. Add a driver to swap between these two clock sources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add an imx6q-cpufreq driver for Freescale i.MX6Q SoC to handle the
hardware specific frequency and voltage scaling requirements.
The driver supports module build and is instantiated by the platform
device/driver mechanism, so that it will not be instantiated on other
platforms, as IMX is built with multiplatform support.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.
This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit b09db45c (cpufreq: OMAP driver depends CPUfreq tables.) This
patch remedies that.
Apologies to Russell King for breaking his originally working patch.
Also, thanks to Grazvydas Ignotas for reporting the same problem.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the CPUFREQ dependency for regarding EXYNOS SoCs
such as EXYNOS4210, EXYNOS4X12 and EXYNOS5250. Its cpufreq
driver should be built with selection of SoC arch part.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull cpufreq updates for 3.4 from Dave Jones: new drivers and some fixes.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
provide disable_cpufreq() function to disable the API.
EXYNOS5250: Add support cpufreq for EXYNOS5250
EXYNOS4X12: Add support cpufreq for EXYNOS4X12
[CPUFREQ] CPUfreq ondemand: update sampling rate without waiting for next sampling
[CPUFREQ] Add S3C2416/S3C2450 cpufreq driver
[CPUFREQ] Fix exposure of ARM_EXYNOS4210_CPUFREQ
[CPUFREQ] EXYNOS4210: update the name of EXYNOS clock register
[CPUFREQ] EXYNOS: Initialize locking_frequency with initial frequency
[CPUFREQ] s3c64xx: Fix mis-cherry pick of VDDINT
Fix up trivial conflicts in Kconfig and Makefile due to just changes
next to each other (OMAP2PLUS changes vs some new EXYNOS cpufreq
drivers).
This patch adds support cpufreq for EXYNOS5250 SoC. Basically,
the exynos-cpufreq.c is used commonly and exynos5250-cpufreq.c
is used for EXYNOS5250(two Cortex-A15 cores) SoC.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch adds support cpufreq for EXYNOS4X12 SoCs. Basically,
the exynos-cpufreq.c is used commonly and exynos4x12-cpufreq.c
is used for EXYNOS4212(two Cortex-A9 cores) and EXYNOS4412(four
Cortex-A9 cores) SoCs.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The S3C2416/S3C2450 SoCs support two sources for the armclk.
The first source is the so called armdiv which divides the msysclk down
to provide necessary cpu rates. In this mode the core voltage must be
always at 1.3V. The frequency from the armdiv is not allowed to be
lower than the hclk frequency.
In the second mode the armclk can be sourced directly from the hclk in
the so called "dynamic voltags scaling" (dvs) mode. Here the armdiv
isn't used at all. Also in this mode the core voltage may be lowered.
Existing hardware and tests with it suggest 1.0V as sufficient.
When changing the clock source to the armdiv from the hclk, the SoC
shows stability issues if the new frequency is higher than the current
hclk frequency. Hence the driver always forces the armdiv to the hclk
frequency before the source change and lets the cpufreq issue another
set_target call for higher frequencies.
To mark the hclk frequency as lower as the corresponding armdiv
frequency it is set 1MHz below the real frequency. This lets the cpufreq
framework change between 133MHz based on hclk and 133MHz based on armdiv
at will.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Andrey Gusakov <dron0gus@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
exynos4210-cpufreq.c is not buildable on non-exynos builds, so it's
pointless allowing this option to be exposed. Fix this by adding a
dependency on ARCH_EXYNOS.
drivers/cpufreq/exynos4210-cpufreq.c:20:29: error: mach/regs-clock.h: No such file or directory
drivers/cpufreq/exynos4210-cpufreq.c:21:26: error: mach/cpufreq.h: No such file or directory
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: cpufreq@vger.kernel.org
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The OMAP driver depends on CPUfreq table support for creating a table
of frequencies from the OPP layer. Ensure that it's build to avoid
link-time errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[khilman@ti.com: make user-selectable, but default y]
Signed-off-by: Kevin Hilman <khilman@ti.com>
To support various EXYNOS series SoCs commonly,
added exynos common structure.
exynos-cpufreq.c => EXYNOS series common cpufreq driver
exynos4210-cpufreq.c => EXYNOS4210 support cpufreq driver
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
According to discussion of the ARM arch subsystem migration,
ARM cpufreq drivers move to drivers/cpufreq. So this patch
adds Kconfig.arm for ARM like x86 and adds Samsung S5PV210
and EXYNOS4210 cpufreq driver compile in there.
As a note, otherw will be moved.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
