this extends the poisoning concept to anchors. This way poisoning
will work with fire and forget drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
looking at usb_kill_urb() it seems to me that it is unnecessarily lenient.
In the use case of disconnect() you never want to use the URB again
(for the same device) But leaving urb->reject elevated will make it easier
to avoid races between read/write and disconnect.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1135) essentially reverts the major parts of two earlier
patches to usbcore, because they ended up causing a regression.
Trying to recover from transient communication errors can lead to
other problems, because operations that failed during the error period
are not always retried. The simplest example is the initial
Set-Config request sent after device enumeration; if it gets lost then
it will not be retried and the device will remain unconfigured.
This patch restores the old behavior in which any port disconnect or
port disable causes the entire device structure to be removed, fixing a
reported regression.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit de85422b94, 'USB: fix interrupt
disabling for HCDs with shared interrupt handlers' changed usb_add_hcd()
to strip IRQF_DISABLED from irqflags prior to calling request_irq()
with the justification that such a removal was necessary for shared
interrupts to work properly. Unfortunately, the change in that commit
unconditionally removes the IRQF_DISABLED flag, causing problems on
platforms that don't use a shared interrupt but require IRQF_DISABLED.
This change adds a check for IRQF_SHARED prior to removing the
IRQF_DISABLED flag.
Fixes the PS3 system startup hang reported with recent Fedora and
OpenSUSE kernels.
Note that this problem is hidden when CONFIG_LOCKDEP=y (ps3_defconfig),
as local_irq_enable_in_hardirq() is defined as a null statement for
that config.
CC: stable <stable@kernel.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Stefan Becker <Stefan.Becker@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1130) fixes an incompatibility between the new PM
infrastructure and USB power management. We are not allowed to call
drivers' probe routines during a system sleep transition between the
"prepare" and "complete" callbacks, but that's exactly what we do when
a driver doesn't have full suspend/resume support. Such drivers are
unbound during the "suspend" call and reprobed during the "resume" call.
The patch causes the reprobe step to be skipped if the "complete"
callback hasn't been issued yet, i.e., if the interface's
dev.power.status field is not equal to DPM_ON. Thus during the
"resume" callback nothing bad will happen, and during the final
"complete" callback the reprobing will occur as desired.
This fixes the problem reported in Bugzilla #11263.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1129) adds support for the new PM callbacks to usbcore.
The new callbacks merely invoke the same old USB power management
routines as the old ones did.
A minor improvement is that the callbacks are present only in the
"USB-device" device_type structure, rather than in the bus_type
structure. This way they will be invoked only for USB devices, not
for USB interfaces. The core USB PM routines automatically handle
suspending and resuming interfaces along with their devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1128) fixes one of the problems related to the new PM
infrastructure. We are not allowed to register new child devices
during the middle of a system sleep transition, but unbinding a USB
driver causes the core to automatically install altsetting 0 and
thereby create new endpoint pseudo-devices.
The patch fixes this problem (and the related problem that installing
altsetting 0 will fail if the device is suspended) by deferring the
Set-Interface call until some later time when it is legal and can
succeed. Possible later times are: when a new driver is being probed
for the interface, and when the interface is being resumed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1127) makes a minor change to the prototypes of the
usb_suspend_interface() and usb_resume_interface() routines. Now the
usb_device structure is passed as an argument, instead of being
computed on-the-fly from the usb_interface argument.
It makes the code look simpler, even if it really isn't much different
from before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Irqs must not accidentally be reenabled.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1123b) fixes a compiler warning: do_unbind_rebind() is
defined but not used if CONFIG_PM=n.
Problem originally found and initial patch submitted by Alexander
Beregalov <a.beregalov@gmail.com>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1122) fixes a bug: When an interface is unregistered,
its children (sysfs files and endpoint devices) are unregistered after
it instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb/core/driver: fix warning:
drivers/usb/core/driver.c:834: warning: 'do_unbind_rebind' defined but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Okay, I found the cause of the hang. It is a simple bug in the USB
scatter-gather library, caused by changes added in response to the S-G
chaining modification.
This patch (as1125) fixes a bug in the USB scatter-gather library.
Early exit from the S-G initialization loop does not reset the count of
outstanding URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Why?:
There are occasions where userspace would like to access sysfs
attributes for a device but it may not know how sysfs has named the
device or the path. For example what is the sysfs path for
/dev/disk/by-id/ata-ST3160827AS_5MT004CK? With this change a call to
stat(2) returns the major:minor then userspace can see that
/sys/dev/block/8:32 links to /sys/block/sdc.
What are the alternatives?:
1/ Add an ioctl to return the path: Doable, but sysfs is meant to reduce
the need to proliferate ioctl interfaces into the kernel, so this
seems counter productive.
2/ Use udev to create these symlinks: Also doable, but it adds a
udev dependency to utilities that might be running in a limited
environment like an initramfs.
3/ Do a full-tree search of sysfs.
[kay.sievers@vrfy.org: fix duplicate registrations]
[kay.sievers@vrfy.org: cleanup suggestions]
Cc: Neil Brown <neilb@suse.de>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Reviewed-by: SL Baur <steve@xemacs.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Mark Lord <lkml@rtr.ca>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1109b) makes USB-Persist more resilient to errors. With
the current code, if a normal resume fails, it's an unrecoverable
error. With the patch, if a normal resume fails (and if the device is
enabled for USB-Persist) then a reset-resume is tried.
This fixes the problem reported in Bugzilla #10977.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix pointer/int cast in USB devio code, and thus avoid a compiler warning.
A void* data argument passed to bus_find_device() and thence to match_devt()
is used to carry a 32-bit datum. However, casting directly between a u32 and
a pointer is not permitted - there must be an intermediate cast via (unsigned)
long.
This was introduced by the following patch:
commit 94b1c9fa060ece2c8f080583beb6cc6008e41413
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Tue Jun 24 14:47:12 2008 -0400
usbfs: simplify the lookup-by-minor routines
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1107) fixes a small bug in the usbfs registration and
unregistration code. It avoids leaving an error value stored in the
device's usb_classdev field and it avoids trying to unregister a NULL
pointer. (It also fixes a rather extreme overuse of whitespace.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1106) fixes a race between opening and unregistering
device files in usbfs. The current code drops its reference to the
device and then reacquires it, ignoring the possibility that the
device structure might have been removed in the meantime. It also
doesn't check whether the device is already in the NOTATTACHED state
when the file is opened.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB device files are accessible in two ways: as files in usbfs and as
character device nodes. The two paths are supposed to behave
identically, but they don't. When the underlying USB device is
unplugged, disconnect signals are sent to processes with open usbfs
files (if they requested these signals) but not to processes with open
device node files.
This patch (as1104) fixes the bug by moving the disconnect-signalling
code into a common subroutine which is called from both paths.
Putting this subroutine in devio.c removes the only out-of-file
reference to struct dev_state, and so the structure's declaration can
be moved from usb.h into devio.c.
Finally, the new subroutine performs one extra action: It kills all
the outstanding async URBs. (I'd kill the outstanding synchronous
URBs too, if there was any way to do it.) In the past this hasn't
mattered much, because devices were unregistered from usbfs only
when they were disconnected. But now the unregistration can also
occur whenever devices are unbound from the usb_generic driver. At
any rate, killing URBs when a device is unregistered from usbfs seems
like a good thing to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1024) takes care of a FIXME issue: Drivers that don't
have the necessary suspend, resume, reset_resume, pre_reset, or
post_reset methods will be unbound and their interface reprobed when
one of the unsupported events occurs.
This is made slightly more difficult by the fact that bind operations
won't work during a system sleep transition. So instead the code has
to defer the operation until the transition ends.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch renames the existing usb_reset_device in hub.c to
usb_reset_and_verify_device and renames the existing
usb_reset_composite_device to usb_reset_device. Also the new
usb_reset_and_verify_device does't need to be EXPORTED .
The idea of the patch is that external interface driver
should warn the other interfaces' driver of the same
device before and after reseting the usb device. One interface
driver shoud call _old_ usb_reset_composite_device instead of
_old_ usb_reset_device since it can't assume the device contains
only one interface. The _old_ usb_reset_composite_device
is safe for single interface device also. we rename the two
functions to make the change easily.
This patch is under guideline from Alan Stern.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
It is the usb interface driver probe() methods that
can't call usb_set_configuration, not usb device driver.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1103) changes the iteration in the USB scatter-gather to
use a standard SG iterator. Otherwise the iteration will fail if it
encounters a chained SG list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From the current implementation of usb_reset_composite_device
function, the iface parameter is no longer useful. This function
doesn't do something special for the iface usb_interface,compared
with other interfaces in the usb_device. So remove the parameter
and fix the related caller.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't allow hubs on the 7th tier as they would allow
devices on the 8th tier.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1091) changes the way usbcore handles interface
unbinding. If the interface's driver supports "soft" unbinding (a new
flag in the driver structure) then in-flight URBs are not cancelled
and endpoints are not disabled. Instead the driver is allowed to
continue communicating with the device (although of course it should
stop before its disconnect routine returns).
The purpose of this change is to allow drivers to do a clean shutdown
when they get unbound from a device that is still plugged in. Killing
all the URBs and disabling the endpoints before calling the driver's
disconnect method doesn't give the driver any control over what
happens, and it can leave devices in indeterminate states. For
example, when usb-storage unbinds it doesn't want to stop while in the
middle of transmitting a SCSI command.
The soft_unbind flag is added because in the past, a number of drivers
have experienced problems related to ongoing I/O after their disconnect
routine returned. Hence "soft" unbinding is made available only to
drivers that claim to support it.
The patch also replaces "interface_to_usbdev(intf)" with "udev" in a
couple of places, a minor simplification.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1083) combines hub_quiesce() and hub_stop() into a
single routine. There's no point keeping them separate since they are
usually called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1071) combines hub_activate() and hub_restart() into a
single routine. There's no point keeping them separate, since they
are always called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1082) makes a small optimization to the way the hub
driver carries out port debouncing immediately after a hub is
activated (i.e., initialized, reset, or resumed). If any port-change
statuses are observed, the code will delay for a minimal debounce
period -- thereby making a good start at debouncing all the ports at
once.
If this wasn't sufficient then khubd will debounce any port that still
requires attention. But in most cases it should suffice; it's rare
for a device to need more than a minimal debounce delay. (In the
cases of hub initialization or reset even that is most likely not
needed, since any devices plugged in at such times have probably been
attached for a while.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1073) adds to khubd a way to recover from power-session
interruption caused by transient connect-change or enable-change
events. After the debouncing period, khubd attempts to do a
USB-Persist-style reset or reset-resume. If it works, the connection
will remain unscathed.
The upshot is that we will be more immune to noise caused by EMI. The
grace period is on the order of 100 ms, so this won't permit recovery
from the "accidentally knocked the USB cable out of its socket" type
of event, but it's a start.
As an added bonus, if a device was suspended when the system goes to
sleep then we no longer need to check for power-session interruptions
when the system wakes up. Khubd will naturally see the status change
while processing the device's parent hub and will do the right thing.
The remote_wakeup() routine is changed; now it expects the caller to
acquire the device lock rather than acquiring the lock itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1081) straightens out the logic of the hub_restart()
routine. Each port of the hub is scanned and the driver makes sure
that ports which are supposed to be disabled really _are_ disabled.
Any ports with a significant change in status are flagged in
hub->change_bits, so that khubd can focus on them without the need to
scan all the ports a second time -- which means the hub->activating
flag is no longer needed.
Also, it is now recognized explicitly that the only reason for
resuming a port which was not suspended is to carry out a reset-resume
operation, which happens only in a non-CONFIG_USB_SUSPEND setting.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Linus's previous patch that is in mainline to make it
easier for the USB hub.c patches that follow this to apply cleanly. The
functionality will be added back in a followon patch in this series.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1080) makes a significant change to the way khubd
handles port connect-change and enable-change events. Both types of
event are now debounced, and the debouncing is carried out _before_ an
existing usb_device is unregistered, instead of afterward.
This means that drivers will have to deal with longer runs of errors
when a device is unplugged, but they are supposed to be prepared for
that in any case.
The advantage is that when an enable-change occurs (caused for example
by electromagnetic interference), the debouncing period will provide
time for the cause of the problem to die away. A simple port reset
(added in a forthcoming patch) will then allow us to recover from the
fault.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1070) creates a new subroutine to check whether a device
can be resumed. This code is needed even when CONFIG_USB_SUSPEND
isn't set, because devices do suspend themselves when the root hub
(and hence the entire bus) is suspended, and power sessions can get
lost during a system sleep even without individual port suspends.
The patch also fixes a loose end in USB-Persist reset-resume handling.
When a low- or full-speed device is attached to an EHCI's companion
controller, the port handoff during resume will cause the companion
port's connect-status-change feature to be set. If that flag isn't
cleared, the port-reset code will think it indicates that the device
has been unplugged and the reset-resume will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Alan's previous patch so that the recent Hub changes will
apply cleanly. The above mentioned patch was needed for 2.6.26 to work
properly.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes usb_create_hcd() to be able to handle the fact that
pci_name() has changed to a constant string.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit e872154921.
Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver. Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example
http://lkml.org/lkml/2008/7/5/236
for an analysis.
The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1111) fixes a bug in the hub driver. When a hub
resumes, disconnections that occurred while the hub was suspended are
lost.
A completely different fix for this problem has already been accepted
for 2.6.27; however the problem still needs to be handled in 2.6.26.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: fix interrupt disabling for HCDs with shared interrupt handlers
As has been discussed several times on LKML, IRQF_SHARED | IRQF_DISABLED
doesn't work reliably, i.e. a shared interrupt handler CAN'T be certain to
be called with interrupts disabled. Most USB HCD handlers use IRQF_DISABLED
and therefore havoc can break out if they share their interrupt with a
handler that doesn't use it.
On my test machine the yenta_socket interrupt handler (no IRQF_DISABLED)
was registered before ehci_hcd and one uhci_hcd instance. Therefore all
usb_hcd_irq() invocations for ehci_hcd and for one uhci_hcd instance
happened with interrupts enabled. That led to random lockups as USB core
HCD functions that acquire the same spinlock could be called twice
from interrupt handlers.
This patch updates usb_hcd_irq() to always disable/restore interrupts.
usb_add_hcd() will silently remove any IRQF_DISABLED requested from HCD code.
Signed-off-by: Stefan Becker <stefan.becker@nokia.com>
Cc: stable <stable@kernel.org>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_open() is protected by a down_read(&minor_rwsem), but I'm not sure I
trust it to protect everything including subsidiary open() functions.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
On some boxes the touchpad needs to be reinitialized after resume to make
it function again. This fixes bugzilla #10825.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch tries to identify which devices are able to accept
reset-resume handling, by checking that there is at least one
interface driver bound and that all of the drivers have a reset_resume
method defined. If these conditions don't hold then during resume
processing, the device is logicall disconnected.
This is only a temporary fix. Later on we will explicitly unbind
drivers that can't handle reset-resumes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like the HP53{00,70} scanner other devices of the OEM Avision require
the USB_QUIRK_STRING_FETCH_255 to correct set a configuration with
"recent" Linux kernels.
Signed-off-by: René Rebe <rene@exactcode.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1094) changes the output of the "descriptors" binary
attribute. Now it will contain the device descriptor followed by all
the configuration descriptors, not just the descriptor for the current
config.
Userspace libraries want to have access to the kernel's cached
descriptor information, so they can learn about device characteristics
without having to wake up suspended devices. So far the only user of
this attribute is the new libusb-1.0 library; thus changing its
contents shouldn't cause any problems.
This should be considered for 2.6.26, if for no other reason than to
minimize the range of releases in which the attribute contains only the
current config descriptor.
Also, it doesn't hurt that the patch removes the device locking --
which was formerly needed in order to know for certain which config was
indeed current.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a potential deadlock when the usb_generic driver is unbound
from a device. The problem is that generic_disconnect() is called
with the device lock held, and it removes a bunch of device attributes
from sysfs. If a user task happens to be running an attribute method
at the time, the removal will block until the method returns. But at
least one of the attribute methods (the store routine for power/level)
needs to acquire the device lock!
This patch (as1093) eliminates the deadlock by moving the calls to
create and remove the sysfs attributes from the usb_generic driver
into usb_new_device() and usb_disconnect(), where they can be invoked
without holding the device lock.
Besides, the other sysfs attributes are created when the device is
registered and removed when the device is unregistered. So it seems
only fitting for the extra attributes to be created and removed at the
same time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1087d) fixes a long-standing problem in usbcore: Device,
interface, and endpoint attributes aren't added until _after_ the
creation uevent has already been broadcast.
Unfortunately there are a few attributes which cannot be created that
early. The "descriptors" attribute is binary and so must be created
separately. The power-management attributes can't be created until
the dev/power/ group exists. And the interface string can vary from
one altsetting to another, so it has to be created dynamically.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I used ohci-sm501, hcd_alloc_coherent() in map_urb_for_dma() is not
called, because usb_sg_init() always sets URB_NO_TRANSFER_DMA_MAP.
dmesg (CONFIG_USB_STORAGE_DEBUG enabled):
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code -75; transferred 0/36
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x2
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove proc_bus export and variable itself. Using pathnames works fine
and is slightly more understandable and greppable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For WUSB devices, usb_dev.devnum is a device index and not the real
device address (which is managed by wusbcore). Therefore, only set
devnum once (in choose_address()) and never change it.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be able to call ep0_reinit() [renamed to usb_ep0_reinit()]
from the WUSB security code. The reason is that when we authenticate
the device, it's address changes (from having bit 7 set to having it
cleared). Thus, we need to signal the USB stack to reinitialize EP0,
so the status with the previous address kept at the HCD layer is
cleared and properly reinitialized.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A WUSB device gets his address during the connection phase; later on,
during the authenthication phase (driven from user space) we assign
the final address. So we need to skip in hub_port_init() the actual
setting of the address for WUSB devices.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify choose_address() so it knows about our special scheme of
addressing WUSB devices (1:1 w/ port number).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1079) cleans up the way URB_* flags are exported in
usbfs.
The URB_NO_INTERRUPT flag is now exported (this is the
only behavioral change).
USBDEVFS_URB_* macros are added for URB_NO_FSBR,
URB_ZERO_PACKET, and URB_NO_INTERRUPT, making explicit the
fact that the kernel accepts them.
The flag matching takes into account that the URB_* values
may change as the kernel evolves, whereas the USBDEVFS_URB_*
values must remain fixed since they are a user API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting. The setting
is then saved in the do_remote_wakeup flag.
Later on, however, the device_may_wakeup() value can change because of
user activity. So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup(). This patch (as1076)
makes that change for root hubs in several places.
The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.
And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1077) logs an error message whenever the kernel is
unable to enumerate a new USB device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the ability to trigger asynchronous unlinks of anchored URBs. This
is needed for error handling in the comntext of completion handlers, which
cannot sleep.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removing an interface's sysfs files before unregistering the interface
doesn't work properly, because usb_unbind_interface() will reinstall
altsetting 0 and thereby create new sysfs files. This patch (as1074)
removes the files after the unregistration is finished. It's not
quite as clean, but at least it works.
Also, there's no need to check if an interface has been registered
before removing its sysfs files. If it hasn't been registered then
the files won't have been created, so usb_remove_sysfs_intf_files()
will simply do nothing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers. They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.
To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume. It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator. However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications. This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove useless @type note for rh_string() and @r note for usb_hcd_irq()
since this two parameters were removed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since this USB feature seems non-experimental, remove that dependency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/devio.c: In function 'proc_control':
drivers/usb/core/devio.c:657: warning: comparison is always false due to limited range of data type
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
power.power_state is scheduled for removal. This patch (as1053)
removes all uses of that field from drivers/usb. Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.
Part of this patch was written by Pavel Machek.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This provides better support for USB "Embedded Host" functionality, which
is a subset of the USB OTG options:
* External hub support can be disabled;
* USB peripherals not whitelisted in "otg_whitelist.h" will be rejected
during enumeration.
These options can allow some savings in software and support.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This teaches EHCI how to to work around bugs in certain high speed
devices, by accomodating "bulk" packets that exceed the 512 byte
constant value required by the USB 2.0 specification. (Have a
look at section 5.8.3, paragraphs 1 and 3.)
It also makes the descriptor parsing code warn when it encounters
such bugs. (We've had reports of maybe two or three such devices,
all pretty recent.)
Such devices are nonconformant. The proper fix is have the vendors
of those devices do the simple, obvious, and correct thing ... which
will let them be used with USB hosts that don't have workarounds for
this particular vendor bug. But unless/until they do, we can at least
have one of the high speed HCDs work with such buggy devices.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a new PM-related change notice for the USB 2.0 specification
called "Link Power Management" (LPM). It defines a new "L1 Suspend"
state which resembles the current (L2) suspend state, except that it
can be entered and exited much more quickly. It should thus be more
useful for runtime PM, even though it doesn't mandate reduced power
draw from VBUS.
This patch provides the relevant #defines for usbcore. Actually
implementing these mechanisms requires host silicon that can generate
new USB packets, plus hubs handling some new requests and peripherals
which understand the new packets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1052) enables USB-PERSIST for all devices by default.
The user won't have to remember to enable it explicitly for devices
containing mounted filesystems.
Eventually userspace tools like hal may be able to set the persist
attribute automatically when a filesystem is mounted on a USB device.
When that time comes this patch can be reverted, if people think it
matters.
This approach has the advantage of giving the user the ability to turn
off USB-PERSIST for devices with mounted filesystems, rather than
making the kernel always assume it should be on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1048) extends the descriptor checking after a device is
reset. Now the SerialNumber string descriptor is compared to its old
value, in addition to the device and configuration descriptors.
As a consequence, the kmalloc() call in usb_string() is now on the
error-handling pathway for usb-storage. Hence its allocation type is
changed to GFO_NOIO.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1047) removes the USB_PERSIST Kconfig option, enabling
it permanently. It also prevents the power/persist attribute from
being created for hub devices; there's no point in having it since
USB-PERSIST is always turned on for hubs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1046) makes USB-PERSIST work more in accordance with
the documentation. Currently it takes effect only in cases where the
root hub has lost power or been reset, but it is supposed to operate
whenever a power session was dropped during a system sleep.
A new hub_restart() routine carries out the duties required during a
reset or a reset-resume. It checks to see whether occupied ports are
still enabled, and if they aren't then it clears the enable-change and
connect-change features (to prevent interference by khubd) and sets
the child device's reset_resume flag. It also checks ports that are
supposed to be unoccupied to verify that the firmware hasn't left the
port in an enabled state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1045) reorganizes some code in the hub driver.
hub_port_status() is moved earlier in the file, and a new hub_stop()
routine is created to do the work currently in hub_preset() (i.e.,
disconnect all child devices and quiesce the hub).
There are no functional changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset. This is necessary because:
When some machines go into suspend, they remove power from
on-board USB devices while retaining suspend current for USB
controllers.
The user might well unplug a USB device while the system is
suspended and then plug it back in before resuming.
A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep. If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.
Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request. A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
debugfs: fix sparse warnings
Driver core: Fix cleanup when failing device_add().
driver core: Remove dpm_sysfs_remove() from error path of device_add()
PM: fix new mutex-locking bug in the PM core
PM: Do not acquire device semaphores upfront during suspend
kobject: properly initialize ksets
sysfs: CONFIG_SYSFS_DEPRECATED fix
driver core: fix up Kconfig text for CONFIG_SYSFS_DEPRECATED
This patch (as1040) fixes up the blacklist of USB device quirks. A
couple of lines are broken to comply with the 80-column rule, and
entries are sorted into the proper numerical order.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1039) updates the Kconfig entry for USB_SUSPEND. The
out-of-date reference to "power/state" is fixed, autosuspend is
mentioned, and the dependency on EXPERIMENTAL is removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix docbook problems in USB source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1033) adds a quirks entry and an unusual_devs entry for
the Actions Semiconductor flash drive. This device has a 64-byte
string descriptor, which it doesn't terminate with a 0-length packet.
Oddly enough, the reporter's logs show that when the device was
plugged in at boot time, it changes its behavior completely -- it uses
a different product ID, product string descriptor, and bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RESET_RESUME entries for some sound devices that need it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Over two years ago, the Linux USB developers stated that they believed
there was no way to create a USB kernel driver that was not under the
GPL. This patch moves the USB apis to enforce that decision.
There are no known closed source USB drivers in the wild, so this patch
should cause no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Turns out that a company is out there using the vendor id of 0x0000 in
the wild, so use a real vendor/product id for the root hubs.
Now that the Linux Foundation has a real vendor id, we use that, and the
first product id:
0x1d6b is the vendor id of the Linux Foundation
0x0001 is the product id for Linux 1.1 root hubs
0x0002 is the product id for Linux 2.0 root hubs
The usb.ids file has already been updated with these values.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: dma bounce buffer support V4
This patch adds dma bounce buffer support to the usb core. These buffers
can be enabled with the HCD_LOCAL_MEM flag, and they make sure that all data
passed to the host controller is allocated using dma_alloc_coherent().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ISO descriptors are allocated separately in proc_submiturb for a fetch
from user mode, then tucked at the end of URB. This seems like a dead code.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports two statistics to userspace:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
connected_duration is the total time (in msec) that the device has
been connected. active_duration is the total time the device has not
been suspended. With these two statistics, tools like PowerTOP can
calculate the percentage time that a device is active, i.e. not
suspended or auto-suspended.
Users can also use the active_duration to check if a device is actually
autosuspended. Currently, they can set power/level to auto and
power/autosuspend to a positive timeout, but there's no way to know from
userspace if a device was actually autosuspended without looking at the
dmesg output. These statistics will be useful in creating an automated
userspace script to test autosuspend for USB devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1022b) adds stub methods for suspend and resume to the
usbfs driver. There isn't much they can do since there's no way to
inform a user task about the events. But it's important to have the
stubs, because an upcoming change to usbcore will automatically unbind
drivers that don't have those methods when a suspend occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1023) updates the code in usb_reset_composite_device():
Some local variable declarations are moved to inner loops.
The interface locks are not acquired. This isn't necessary
any more; its only reason was to prevent an interface from
being suspended or resumed during the reset. But now
interface power management is controlled by the USB device
lock, not by the interface lock.
The check for whether the interface is registered is removed.
There doesn't seem to be any reason for checking; a driver
for a non-registered interface deserves to be informed of
device resets just as much as any other.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For as long as I've known about it, the USBDEVFS_CONNECT ioctl hasn't
done what it's supposed to. The current code reprobes _all_ the
unbound USB interfaces; this patch (as1021) makes it reprobe only the
interface for which it was called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Distros (like SuSE) want to know this information, to make it easier
to handle support issues. Might as well let everyone benefit from this.
This is also enabled whenever CONFIG_USB_DEBUG is enabled, to help with
debugging.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch hands over the port to the companion when the
hub_port_connect_change fails.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1016) prevents PCI-based host controllers from
undergoing a power-state change during a FREEZE or a PRETHAW. Such
changes are needed only during a SUSPEND.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1012b) makes the ksuspend_usbd kernel thread
non-freezable. Since the PM core has been changed to lock all devices
during a system sleep, the thread no longer needs to be frozen. It
won't interfere with a system sleep because before trying to resume a
root hub device, it acquires the device's lock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert from class_device to device for drivers/usb/core.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some crazy devices in the wild have a vendor id of 0x0000. If we try to
add a module alias with this id, we just can't do it due to a check in
the file2alias.c file. Change the test to verify that both the vendor
and product ids are 0x0000 to show a real "blank" module alias.
Note, the module-init-tools package also needs to be changed to properly
generate the depmod tables.
Cc: Janusz <janumix@poczta.fm>
Cc: stable <stable@kernel.org>
Cc: Jon Masters <jcm@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this function will run in the context of the scsi error handler thread.
It must use GFP_NOIO instead of GFP_KERNEL to avoid a possible
deadlock.
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects the wrong function name mentioned in the comments
of usb_unregister_notify function.
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't try to call the "raw" sysfs_create_file when we already have a
helper function to do this kind of work for us.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Host controller IRQs are supposed to be serviced with interrupts
disabled. This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it. It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().
This fixes Bugzilla #9335.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().
This fixes Bugzilla #9532.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1010) was written by both Kay Sievers and me. It solves
the problem of duplicated keys in USB uevent structures by refactoring
the uevent subroutines, taking advantage of the way the hotplug core
calls uevent handlers for the device's bus and for the device's type.
Keys needed for both USB-device and USB-interface events are added in
usb_uevent(), which is the bus handler. Keys appropriate only for
USB-device or USB-interface events are added in usb_dev_uevent() or
usb_if_uevent() respectively, the type handlers.
In addition, unnecessary tests for NULL pointers are removed as are
duplicated debugging log statements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1009) solves the problem of multiple registrations for
USB sysfs files in a more satisfying way than the existing code. It
simply adds a flag to keep track of whether or not the files have been
created; that way the files can be created or removed as needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Arnd Bergmann wrote:
usb_hcd_flush_endpoint() has a retry loop that starts with a spin_lock_irq(),
but only gives up the spinlock, not the irq_disable before jumping to the
rescan label.
Alan Stern:
I agree with your sentiment, but it would be better to solve this
problem without using local_irq_disable().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch renames the IOMMU config option to GART_IOMMU because in fact it
means the GART and not general support for an IOMMU on x86.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch (as1005) fixes a rather subtle problem. When
usb_set_configuration() registers the interfaces and their files in
sysfs, it doesn't expect those files to exist already. But when an
interface is registered, its driver may call usb_set_interface() and
thereby cause the sysfs files to be created. The result is an error
when usb_set_configuration() goes on to create those same files again.
The (not-so-great) solution is to have usb_set_configuration() remove
any existing files before creating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
URB_FREE_BUFFER needs to be allowed in the sanity checks to use drivers that
use that flag.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce freezer-friendly wrappers around wait_event_interruptible() and
wait_event_interruptible_timeout(), originally defined in <linux/wait.h>, to
be used in freezable kernel threads. Make some of the freezable kernel
threads use them.
This is necessary for the freezer to stop sending signals to kernel threads,
which is implemented in the next patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the following cleanups that are now possible:
- remove the unused security_operations->inode_xattr_getsuffix
- remove the no longer used security_operations->unregister_security
- remove some no longer required exit code
- remove a bunch of no longer used exports
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix USB docbook warnings.
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:487): No description found for parameter 'g'
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:506): No description found for parameter 'g'
Warning(linux-2.6.23-git8//drivers/usb/core/hub.c:1416): No description found for parameter 'usb_dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
This patch (as1002) fixes a small race which can occur when a driver
expects usbcore to reschedule an autosuspend request. If the request
arrives too late, it won't be rescheduled. The patch adds an extra
argument to autosuspend_check(), indicating that a reschedule is
needed no matter how much time has elapsed.
It also tries to avoid letting asynchronous changes to the value of
jiffies cause a delay to become negative, by caching a local copy of
the current time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
System suspends and hibernation are supposed to be as transparent as
possible. By this reasoning, if a USB device is already autosuspended
before the system sleep begins then it should remain autosuspended
after the system wakes up.
This patch (as1001) adds a skip_sys_resume flag to the usb_device
structure and uses it to avoid waking up devices which were suspended
when a system sleep began.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order. If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused. The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
powertop currently tracks interrupts generated by uhci, ehci, and ohci,
but it has no way of telling which USB device to blame USB bus activity on.
This patch exports the number of URBs that are submitted for a given device.
Cat the file 'urbnum' in /sys/bus/usb/devices/.../
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as995) cleans up the remains of the former NO_AUTOSUSPEND
quirk. Since autosuspend is disabled by default, we will let
userspace worry about which devices can safely be suspended. Thus the
lengthy series of quirk entries is no longer needed, and neither is
the quirk ID. I suppose someone might eventually run across a hub
that can't be suspended; let's ignore the possibility for now.
The patch also cleans up the hasty way in which autosuspend gets
disabled. Setting udev->autosuspend_delay to -1 wasn't quite right,
because the value is always supposed to be a multiple of HZ. It's
better to leave the delay value alone and set autosuspend_disabled,
which is what the quirk routine used to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as992) fixes a recently-added bug. During a FREEZE or
PRETHAW suspend notification, non-root devices don't actually get
suspended. So we shouldn't tell their parent hubs that they did.
(This code path used to be skipped over, until the FREEZE/PRETHAW test
got moved out of usb_suspend_both() into generic_suspend().)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (jx001) fixes a variable assignment mistake in hub driver.
limited_power should be set to 0 if the hub is self-powered,and 1 if
the hub is bus-powered.
However, the effect of the code was exactly opposite to the spec's
statement for the Local Power Source field. The spec says, this field
is 1 meaning Local power supply lost while this field is 0 indicating
Local power supply good.(This statement is very confusing.)
So this patch switchs the 0 and 1.
Signed-off-by: Jason Xiao <jidong.xiao@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as989) makes usbcore flush all outstanding URBs for each
device as the device is suspended. This will be true even when
CONFIG_USB_SUSPEND is not enabled.
In addition, an extra can_submit flag is added to the usb_device
structure. That flag will be turned off whenever a suspend request
has been received for the device, even if the device isn't actually
suspended because CONFIG_USB_SUSPEND isn't set.
It's no longer necessary to check for the device state being equal to
USB_STATE_SUSPENDED during URB submission; that check can be replaced
by a check of the can_submit flag. This also permits us to remove
some questionable references to the deprecated power.power_state field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as988) breaks usb_hcd_endpoint_disable() apart into two
routines. The first, usb_hcd_flush_endpoint() does the -ESHUTDOWN
unlinking of all URBs in the endpoint's queue and waits for them to
complete. The second, usb_hcd_disable_endpoint() -- renamed for
better grammatical style -- merely calls the HCD's endpoint_disable
method. The changeover is easy because the routine currently has only
one caller.
This separation of function will be exploited in the following patch:
When a device is suspended, the core will be able to cancel all
outstanding URBs for that device while leaving the HCD's
endpoint-related data structures intact for later.
As an added benefit, HCDs no longer need to check for existing URBs in
their endpoint_disable methods. It is now guaranteed that there will
be none.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as987) changes the way FREEZE and PRETHAW suspend events
are handled in usbcore. The decision about whether or not to ignore
them for non-root devices is pushed down into the USB-device driver,
instead of being made in the core code.
This is appropriate, since devices exported to a virtualized guest or
over a network may indeed need to handle these types of suspend, even
though normal devices don't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as990) removes an annoying debugging message. Nobody
really cares when endpoint pseudo-devices are released.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as981) removes the remaining nontrivial usages of
urb->status from usbcore.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>