While playing with the firmware a while back, I discovered a way to
access the device's entire address space before the firmware has been
loaded.
Previously we were loading the firmware early on (during probe) so that
we could read the MAC address from the EEPROM and register a netdevice.
Now that we can read the EEPROM without having firmware, we can defer
firmware loading until later while still reading the MAC address early
on.
This has the advantage that zd1211rw can now be built into the kernel --
previously if this was the case, zd1211rw would be loaded before the
filesystem is available and firmware loading would fail.
Firmware load and other device initialization operations now happen the
first time the interface is brought up.
Some architectural changes were needed: handling of the is_zd1211b flag
was moved into the zd_usb structure, MAC address handling was obviously
changed, and a preinit_hw stage was added (the order is now: init,
preinit_hw, init_hw).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Zen Kato
zd1211b chip 0411:00da v4810 high 00-16-01 AL2230S_RF pa0 g--N-
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zen Kato has a device which reports the 0xa RF type. The vendor driver
treats this as AL2230S, the same as devices with the AL2230S bit in the POD.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zen Kato's device has a regulatory domain value of 0x49, which is not an
IEEE 802.11 code and is not even identified in the vendor driver.
Recent versions of the vendor driver don't even look at the regdomain
value any more, and just allow channels 1-11 everywhere. This patch
brings us more in line with that behaviour, by allowing channels 1-11
for regdomains which we don't know about.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver code suggests that CR47 patching happens on every channel
change for every RF (depending on bit 8 in POD).
Due to a bug in their driver (upper bits of RF_Mode get zeroed out, then
are examined for 1s when setting some other flags), this isn't actually
what happens, and their generic CCK patching routine never takes effect.
Some of their RF configurations do include explicit (duplicated) code
for CR47 patching though. This patch makes zd1211rw match that
behaviour.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for another radio appearing in new devices: the
Ubec UW2453. It's more complicated than the other RF's we support, but
Ubec publish full tech specs so we're able to understand the vendor code
relatively well.
Now that we support UW2453, we also support Atheros' new USB chip: the
AR5007UG. From the little info we have, this appears to be just a
rebranded ZD1211B.
This RF code doesn't work very well -- lots more TX/RX errors than the
other RFs. However, the vendor driver doesn't do any better, so this is
all we can do for now.
[kune@deine-taler.de: bug fixes]
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These changes are needed for UW2453 RF support:
Add pointer which RF drivers can use to store private RF data
Add exit hook so that RF drivers can free private data
Allow RF's to disable the generic TX power integration handling code
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Guy Gallagher
zd1211 chip 0586:3407 v4721 high 00-13-49 AL2230_RF pa0 g---
FCC ID SI5WUB200Z
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by davo on IRC
zd1211b chip 0586:3413 v4810 full 00-13-49 AL7230B_RF pa0 -----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is another "driverless" device which first presents itself as a USB
CDROM drive. A separate patch has been submitted to make usb-storage
ignore that device, so that zd1211rw can eject it.
zd1211 chip 0df6:9075 v4916 full 00-0c-f6 AL2230_RF pa0 ----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alan Tam <Tam at SiuLung dot com> asked for inclusion of this
device into the tree.
zd1211b chip 0053:5301 v4810 high 00-90-cc AL2230_RF pa0 ---N
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Christoph Sager and Tomas Klas
zd1211b chip 0586:3412 v4810 high 00-13-49 AL7230B_RF pa0 g----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for some new ZD1211B devices which ship with
the AL7230B RF.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change allows RF drivers to provide their own 6M band edge patching
implementation, while providing a generic implementation shared by most
currently supported RF's.
The upcoming ZD1211B/AL7230B code will use this to define its own
patching function, which is different from the other RF configurations.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver only does the CR123 write for non-USB devices (which
don't exist on the consumer market)
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by TiCPU on irc
zd1211 chip 13b1:001e v4802 high 00-14-bf AL2230_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using monitor mode, Johannes Berg observed out that lots of corrupted
and otherwise invalid frames were being passed to the host.
When in monitor mode we were disabling the hardware filtering here, but
this is not how monitor mode should work.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a backport of Helge Deller's recent patch for wireless-dev.git
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ASUS A9Rp
Tested by Serge
zd1211b chip 0b05:171b v4802 high 00-17-31 AL2230_RF pa0 g--
ZyXEL G-202
Tested by Marcus D. Hanwell
zd1211b chip 0586:3410 v4810 high 00-13-49 AL2230_RF pa0 g---
US Robotics USR805423
Tested by Pascal S. de Kloe
FCC ID: RAXWN4501H
zd1211b chip 0baf:0121 v4810 high 00-14-c1 AL2230_RF pa0 g--N
Julien Pinon reports this also comes in AL2230S form
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ZD1211 appears to be back in production: a number of new devices have
been appearing! Some of them are using new radios.
This patch adds support for the next generation AL2230 RF chip which has
been spotted in a few new devices.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Suggested by Maxime Austruy, based on mac80211 changes from Stephen
Hemminger
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch commented that GFP_NOFS should not be used in a
network driver.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors the wireless Kconfig all over and already
introduces net/wireless/Kconfig with just the WEXT bit for now,
the cfg80211 patch will add to that as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USRobotics Wireless Adapter (Model 5423) works well with current
zd1211rw driver also (i have tested 2.6.18, 2.6.20 and 2.6.21-rc7).
It just needs its ID added to the list of devices.
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to conflicting/confusing defines in the vendor driver, we were
reading E2P_PHY_REG from the wrong location.
CR157 patching was slightly incorrect in that the vendor driver only
patches in an 8-bit value, whereas we were patching 24 bits.
Additionally, CR157 patching was happening on both zd1211 and zd1211b,
but this should only happen on zd1211.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw currently detects AL2230S-based devices as AL2230, and hence
programs the RF incorrectly. Transmit silently fails on this
misconfiguration.
After this patch, AL2230S devices are rejected with an error message, to
avoid any confusion with an apparent driver bug.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Robert P.J. Day's recent commit ("getting rid of all casts of
k[cmz]alloc() calls") introduced a sparse warning for zd1211rw,
related to our type-checking of addresses.
zd_chip.c:116:15: warning: implicit cast to nocast type
This patch readds the type cast, it is correct.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This causes a lot of uninteresting output in noisy environments, and
doesn't really serve any purpose.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added update of network device error statistics.
Based on earlier work by Maxime Austruy.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This resets the device in the probe call. It does work with
2.6.19.2 including the softmac patches. It might fix the
reboot/reset problems a lot of people reported.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
usb_init should call destroy_workqueue when usb_register fails.
Signed-off-by: Maxime Austruy <maxime@tralhalla.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Marijn Schouten
zd1211b chip 0586:340f v4810 high 00-13-49 AL2230_RF pa0 g---
FCC ID: I88G220V2
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Henrik Hjelte
zd1211b chip 13b1:0024 v4802 high 00-14-bf AL2230_RF pa0 ----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing our own custom 32-bit addresses around and
translating them, this patch makes all our register address constants
absolute and removes the translation.
There are two ugly parts:
- fw_reg_addr() is needed to compute addresses of firmware registers, as this
is dynamic based upon firmware
- inc_addr() needs a small hack to handle byte vs word addressing
However, both of those are only small, and we don't use fw_regs a whole
lot anyway.
The bonuses here include simplicity and improved driver readability. Also, the
fact that registers are now referenced by 16-bit absolute addresses (as
opposed to 32-bit pseudo addresses) means that over 2kb compiled code size has
been shaved off.
Includes some touchups and sparse fixes from Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw address space has confused me once too many times. This
patch introduces the following naming notation:
Memory space is split into segments (cr, fw, eeprom) and segments may
contain components (e.g. boot code inside eeprom). These names are
arbitrary and only for the description below:
x_START: Absolute address of segment start
(previously these were named such as CR_BASE_OFFSET, but they weren't
really offsets unless you were considering them as an offset to 0)
x_LEN: Segment length
x_y_LEN: Length of component y of segment x
x_y_OFFSET: Relative address of component y into segment x. The absolute
address for this component is (x_START + x_y_OFFSET)
I also renamed EEPROM registers to EEPROM data. These 'registers' can't
be written to using standard I/O and really represent predefined data
from the vendor.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many of the registers written during ZD1211 HMAC initialization are
duplicated exactly for ZD1211B. Move the identical ones into a generic
part, and write the hardware-specific ones separately.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver called ieee80211_rx in hardware interrupt context. This has
been against the intention of the ieee80211_rx function. It caused a bug
in the crypto routines used by WPA. This patch calls ieee80211_rx in a
tasklet.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for multicast adresses is implemented by supporting the
set_multicast_list() function of the network device. Address
filtering is supported by a group hash table in the device.
This is based on earlier work by Benoit Papillaut. Fixes multicast packet
reception and ipv6 connectivity:
http://bugzilla.kernel.org/show_bug.cgi?id=7424http://bugzilla.kernel.org/show_bug.cgi?id=7425
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed for NetworkManager users to connect to WPA networks.
Pointed out by Matthew Campbell.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
e.g.
usb 1-7: rx_urb_complete() *** first fragment ***
usb 1-7: rx_urb_complete() *** second fragment ***
drivers/net/wireless/zd1211rw/zd_mac.c:1063 ASSERT
(((current_thread_info()->preempt_count) & (((1UL << (12))-1) << ((0 +
8) + 8)))) VIOLATED!
[<f0299448>] zd_mac_rx+0x3e7/0x47a [zd1211rw]
[<f029badc>] rx_urb_complete+0x22d/0x24a [zd1211rw]
[<b028a22f>] urb_destroy+0x0/0x5
[<b01f0930>] kref_put+0x65/0x72
[<b0288cdf>] usb_hcd_giveback_urb+0x28/0x57
[<b02950c4>] qh_completions+0x296/0x2f6
[<b0294b21>] ehci_urb_done+0x70/0x7a
[<b0294ea1>] qh_completions+0x73/0x2f6
[<b02951bc>] ehci_work+0x98/0x538
Remove the bogus assertion, and use dev_kfree_skb_any as pointed out by
Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.
Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.
Signed-Off-By: David Howells <dhowells@redhat.com>
