There's a currently-unused lgdt3304 demod driver, which leaves a lot to
be desired as far as functionality. The 3304 is unsurprisingly quite
similar to the 3305, and empirical testing yeilds far better results
and more complete functionality by merging 3304 support into the 3305
driver. (For example, the current lgdt3304 driver lacks support for
signal strength, snr, ucblocks, etc., which we get w/the lgdt3305).
For the moment, not dropping the lgdt3304 driver, and its still up to
a given device's config setup to choose which demod driver to use, but
I'd suggest dropping the 3304 driver entirely.
As a follow-up to this patch, I've got another patch that adds support
for the KWorld PlusTV 340U (ATSC) em2870-based tuner stick, driving
its lgdt3304 demod via this lgdt3305 driver, which is what I used to
successfully test this patch with both VSB_8 and QAM_256 signals.
A few pieces are still a touch crude, but I think its a solid start,
as well as much cleaner and more feature-complete than the existing
lgdt3304 driver.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is used when the USB video interface is checked by
the subdriver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- variable / function rename
- set the gains in one exchange
- don't alter the register 80 which contains the AWB flag
and other sensor specific values
- the global gain is now the average of the R, G and B gains.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also renames the last polling message from the closer one
of the ms-windows driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new table is sorted and extracted from a clear part of the MS-Windows
driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also changes a bit the contrast control.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These registers seem to act on the JPEG compression whose control
is not implemented in the current driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG header is now included in the subdriver structure instead
of being allocated and freed at capture start and stop.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
setcolors(0 is a no-op for 7670 sensors, so we should not report a
saturation control for 7670 sensors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
What we've called brightness so far actually is an exposure control,
rename it and fixup the maximum and default values.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a problem with certain tv8532 cams, where sometimes there
hsync/vsync locks one pixel of where it normally locks. While trying to
fix this (which I failed to do). I noticed there are lots if duplicate
register writes and unnecessary register reads in the tv8532 driver. This
patch cleanes these ups (which has no negative effects, but unfortunately
also does not help).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the ovfx2 bridge sometimes the first few frames in a stream
would be no good, as the bridge and sensor are not in complete hsync /
vsync yet. This can easily be detected by checking the framesize. So if the
framesize is short and it is one of the 1ste 3 frames after an sd_start,
drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Partially revert changeset 0208bef609242a2d50b95edc713a41566cae500b:
As pointed by Stefan Ringel <stefan.ringel@arcor.de>, many packets become
damaged by this change. That means that the "size" field of Video/VBI is not
presenting 180 bytes, as it should be expected.
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several missing things at the driver, preventing, for example,
the code to start/stop DMA to actually work. Fix them before implementing
a routine to store data at the audio buffers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implements a callback to be used by tm6000-alsa, in order to allow filling
audio data packets.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to better document and be sure that the values are used
at the proper places, convert extension type into an enum and
name it as "type", instead of "id".
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new driver for the Windows Media Center Edition/eHome
Infrared Remote transceiver devices. Its a port of the current
lirc_mceusb driver to ir-core, and currently lacks transmit support,
but will grow it back soon enough... This driver also differs from
lirc_mceusb in that it borrows heavily from a simplified IR buffer
decode routine found in Jon Smirl's earlier ir-mceusb port.
This driver has been tested on the original first-generation MCE IR
device with the MS vendor ID, as well as a current-generation device
with a Topseed vendor ID. Every receiver supported by lirc_mceusb
should work equally well. Testing was done primarily with RC6 MCE
remotes, but also briefly with a Hauppauge RC5 remote, and all works
as expected.
v2: fix call to ir_raw_event_handle so repeats work as they should.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the RC6 keymap for the Windows Media Center Edition remotes
that come bundled with MCE/eHome Infrared Remote transceivers. Tested
with 3 different variants of the remote, but its possible there are
still some additional keys missing, but its simple enough to add them
in later...
This patch also adds an IR_TYPE_ALL convenience macro to make life
easier for receivers that support all IR protocols.
v2: fix an erroneous comment that referred to imon devices
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than registering all IR protocol decoders as enabled when bringing
up a new device, only enable the IR protocol decoder that matches the
keymap being loaded. Additional decoders can be enabled on the fly by
those that need to, either by twiddling sysfs bits or by using the
ir-keytable util from v4l-utils.
Functional testing done with the mceusb driver, and it behaves as expected,
only the rc6 decoder is enabled, keys are all handled properly, etc.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Fri, May 28, 2010 at 3:59 PM, Jarod Wilson <jarod@redhat.com> wrote:
> The mceusb driver I'm about to submit handles just about any raw IR you
> can throw at it. The ir-core loads up all protocol decoders, starting
> with NEC, then RC5, then RC6. RUN_DECODER() was trying them in the same
> order, and exiting if any of the decoders didn't like the data. The
> default mceusb remote talks RC6(6A). Well, the RC6 decoder never gets a
> chance to run unless you move the RC6 decoder to the front of the list.
>
> What I believe to be correct is to have RUN_DECODER keep trying all of
> the decoders, even when one triggers an error. I don't think the errors
> matter so much as it matters that at least one was successful -- i.e.,
> that _sumrc is > 0. The following works for me w/my mceusb driver and
> the default decoder ordering -- NEC and RC5 still fail, but RC6 still
> gets a crack at it, and successfully does its job.
>
> Signed-off-by: Jarod Wilson <jarod@redhat.com>
>
> ---
> drivers/media/IR/ir-raw-event.c | 7 ++++---
>
> diff --git a/drivers/media/IR/ir-raw-event.c b/drivers/media/IR/ir-raw-event.c
> index ea68a3f..44162db 100644
> --- a/drivers/media/IR/ir-raw-event.c
> +++ b/drivers/media/IR/ir-raw-event.c
> @@ -36,14 +36,15 @@ static DEFINE_SPINLOCK(ir_raw_handler_lock);
> */
> #define RUN_DECODER(ops, ...) ({ \
> struct ir_raw_handler *_ir_raw_handler; \
> - int _sumrc = 0, _rc; \
> + int _sumrc = 0, _rc, _fail; \
> spin_lock(&ir_raw_handler_lock); \
> list_for_each_entry(_ir_raw_handler, &ir_raw_handler_list, list) { \
> if (_ir_raw_handler->ops) { \
> _rc = _ir_raw_handler->ops(__VA_ARGS__); \
> if (_rc < 0) \
> - break; \
> - _sumrc += _rc; \
> + _fail++; \
> + else \
> + _sumrc += _rc; \
Self-NAK. The only place we actually *care* about the retval from a
RUN_DECODER() call is in __ir_input_register(), and currently, its
looking for retval < 0, which is currently never possible. When we're
running the decoders, either they fail and return -EINVAL or they
succeed and return 0, and in the register case, we get either a
negative error (ex: -ENOMEM from rc6) or 0, so with the above, _sumrc
will *always* be 0 in the two cases I'm looking at. The third place
where RUN_DECODER gets called (decoder unregister) doesn't care about
the retval either. New patch below, including updated comments about
the macro.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
move dvb into a separate kern module
[mchehab@redhat.com: Fix several compilation breakages]
Signed-off-by: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix video decoder overflow and avoid junk audio packets
when TV signal is lost.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge function copy streams() and copy_packets() into a new function
copy_streams(), fixing the bugs.
Signed-off-by: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With enabled debugging sh_mobile_ceu_camera.c dereferences an invalid or a NULL
pointer. Thanks to James Wang for reporting.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These function are needed to use camera.
This patch was tested with sh_mobile_ceu_camera
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
