This enables us to have a default device tree per SoC family to be built
into the kernel. The default device tree for XLP3xx has been added as part
of this change. Later this can be used to provide support default boards
for XLP2xx and XLP9xx SoCs.
Kconfig options are provided for each default device tree so that just the
needed ones can be selected to be built into the kernel.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5023/
Acked-by: John Crispin <blogic@openwrt.org>
The index for a device interrupt in the PIC interrupt routing table
changes for different chips in the XLP family. Avoid using the fixed
entries and derive the index value from the SoC device header.
Add workarounds for some devices which do not report the IRT index
correctly.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5025/
Acked-by: John Crispin <blogic@openwrt.org>
Use standard function to print cpumask. Also fixup the name of the
variable used and make it static.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5024/
Acked-by: John Crispin <blogic@openwrt.org>
On multi-chip boards, the first core on slave SoCs may take much
more time to wakeup. Add code to wait for the core to come up before
proceeding with the rest of the boot up.
Update xlp_wakeup_core to also skip the boot node and the boot CPU
initialization which is already complete.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4783/
Signed-off-by: John Crispin <blogic@openwrt.org>
Doing calibrate delay on a hardware thread will be inaccurate since
it depends on the load on other threads in the core. It will also
slow down the boot process when done for 128 hardware threads. Switch
to a pre-computed loops per jiffy based on the core frequency. The
value is computed based on the core frequency and roughly matches the
value calculated by calibrate_delay().
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4791/
Signed-off-by: John Crispin <blogic@openwrt.org>
The XLR/XLS/XLP PIC has a 8 countdown timers which run at the PIC
frequencey. One of these can be used as a clocksource to provide
timestamps that is common across cores. This can be used in place
of the count/compare clocksource which is per-CPU.
On XLR/XLS PIC registers are 32-bit, so we just use the lower 32-bits
of the PIC counter. On XLP, the whole 64-bit can be used.
Provide common macros and functions for PIC timer registers on XLR/XLS
and XLP, and use them to register a PIC clocksource.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4786/
Signed-off-by: John Crispin <blogic@openwrt.org>
Since we now use r4k cache code for Netlogic XLP, it is
better to split L1 icache among the active threads, so that
threads won't step on each other while flushing icache.
The L1 dcache is already split among the threads in the core.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4787/
Signed-off-by: John Crispin <blogic@openwrt.org>
Provide functions ack_c0_eirr(), set_c0_eimr(), clear_c0_eimr()
and read_c0_eirr_and_eimr() that do the EIMR and EIRR operations
and update the interrupt handling code to use these functions.
Also, use the EIMR register functions to mask interrupts in the
irq code.
The 64-bit interrupt request and mask registers (EIRR and EIMR) are
accessed when the interrupts are off, and the common operations are
to set or clear a bit in these registers. Using the 64-bit c0 access
functions for these operations is not optimal in 32-bit, because it
will disable/restore interrupts and split/join the 64-bit value during
each register access.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4790/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add support for XLS6xx CPUs to the Fast Message Network (FMN)
configuration.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4785/
Signed-off-by: John Crispin <blogic@openwrt.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The commit 2a37b1a "MIPS: Netlogic: Move from u32 cpumask to cpumask_t"
breaks uniprocessor compilation on XLR with:
arch/mips/netlogic/xlr/setup.c: In function 'prom_init':
arch/mips/netlogic/xlr/setup.c:196:6: error: unused variable 'i'
Fix by defining 'i' only when CONFIG_SMP is defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4760/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers to
all work together nicer, which was a reduction in overall code. We also
deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a nice
thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhIYACgkQMUfUDdst+yk9gACgsZYgMtbrqdbhbjbYkfO7nYkB
iegAoIvj3qwe33TbZ8OJnIkaWcMiT8CW
=u6Bf
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers
to all work together nicer, which was a reduction in overall code. We
also deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a
nice thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (228 commits)
USB: mark uas driver as BROKEN
xhci: Add Lynx Point LP to list of Intel switchable hosts
uwb: fix uwb_dev_unlock() missed at an error path in uwb_rc_cmd_async()
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
MAINTAINERS: remove drivers/block/ub.c
USB: chipidea: fix use after free bug
ezusb: add dependency to USB
usb: ftdi_sio: fixup BeagleBone A5+ quirk
USB: cp210x: add Virtenio Preon32 device id
usb: storage: remove redundant memset() in usb_probe_stor1()
USB: option: blacklist network interface on Huawei E173
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
USB: add new zte 3g-dongle's pid to option.c
USB: opticon: switch to generic read implementation
USB: opticon: refactor reab-urb processing
USB: opticon: use usb-serial bulk-in urb
USB: opticon: increase bulk-in size
USB: opticon: use port as urb context
USB: opticon: pass port to get_serial_info
USB: opticon: make private data port specific
...
All architectures that use cmd_dtc do so in almost the same way. Create
a central build rule to avoid duplication. The one difference is that
most current uses of dtc build $(obj)/%.dtb from $(src)/dts/%.dts rather
than building the .dtb in the same directory as the .dts file. This
difference will be eliminated arch-by-arch in future patches.
MIPS is the exception here; it already uses the exact same rule as the
new common rule, so the duplicate is removed in this patch to avoid any
conflict. arch/mips changes courtesy of Ralf Baechle.
Update Documentation/kbuild to remove the explicit call to cmd_dtc from
the example, now that the rule exists in a centralized location.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
On XLR/XLS, the cpu cores communicate with fast on-chip devices
(e.g. network accelerator, security engine etc.) using the Fast
Messaging Network(FMN). The FMN queues and credits needs to be
configured and intialized before it can be used.
The co-processor 2 on XLR/XLS CPU cores has registers for FMN access,
and the XLR/XLS has custom instructions for sending and loading
messages. The FMN can deliver also per-cpu interrupts when messages
are available at the CPU.
This patch adds FMN initialization, adds interrupt setup and handling,
and also provides support for sending and receiving FMN messages.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4468
Signed-off-by: John Crispin <blogic@openwrt.org>
Create struct nlm_pic_irq for interrupts handled by the PIC.
This simplifies IRQ handling for multi-SoC as well as
the single SoC cases. Also split the setup of percpu and PIC
interrupts so that we can configure the PIC interrupts for
every node.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4467
Signed-off-by: John Crispin <blogic@openwrt.org>
There can be 1, 2 or 4 SoCs(nodes) in a multi-chip XLP board. Add an
option for multi-chip boards in case of XLP, and make the number of
nodes configurable.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4470
Signed-off-by: John Crispin <blogic@openwrt.org>
Upto 4 Netlogic XLP SoCs can be connected over ICI links to form a
coherent multi-node system. Each SoC has its own set of on-chip
devices including PIC. To support this, add a per SoC stucture and
use it for the PIC and SYS block addresses instead of using global
variables.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4469
Signed-off-by: John Crispin <blogic@openwrt.org>
Initial code to support more than 32 cpus. The platform CPU mask
is updated from 32-bit mask to cpumask_t. Convert places that use
cpu_/cpus_ functions to use cpumask_* functions.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4464
Signed-off-by: John Crispin <blogic@openwrt.org>
The cpuid was not passed into early_init_secondary even though the
comment indicated that it will be. Fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4458
Signed-off-by: John Crispin <blogic@openwrt.org>
At this point early printk is available, so debugging device tree
issues is easier.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4460
Signed-off-by: John Crispin <blogic@openwrt.org>
Enable Speculative Unmap Enable bit, which will enable speculative L2
cache requests for unmapped memory. This should give better performance
for kernel code/data which is in KSEG0
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4461
Signed-off-by: John Crispin <blogic@openwrt.org>
The OHCI platform driver is suitable for use by the Netlogic XLR platform
so use this driver instead of the OHCI XLS platform driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EHCI platform driver is suitable for use by the Netlogic XLR platform
since there is nothing specific that the EHCI XLR platform driver does.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide a config option to embed a device tree for XLP evaluation
boards. This DTB will be used if the firmware does not pass in a
device tree pointer.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4103/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add the serial ports to the device tree and remove the platform
code for adding them.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4098/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add a basic DTS file netlogic/dts/nlm_xlp.dts which contains
memory, i2c devices, NOR flash and command line arguments.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4100/
Signed-off-by: John Crispin <blogic@openwrt.org>
Move the function device_tree_init() from netlogic/xlp/of.c
to setup.c, and remove the wrapper functions reserve_mem_mach()
and free_mem_mach().
Remove file netlogic/xlp/of.c, and the Makefile entry for it.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4097/
Signed-off-by: John Crispin <blogic@openwrt.org>
In prom_putchar(), wait for just the TX empty bit to clear in the
UART LSR.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Cc: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/4112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[ralf@linux-mips.org: I've folded most segments of this patch into those
patches in -next that originally were causing the whitespace damage.
This is just what's left over]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4094/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe and add devices on SoC "simple-bus" on startup. This will
in turn add devices like I2C controller that are specified in the
device tree under 'soc'.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3762/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XLP USB controller appears as a device on the internal SoC PCIe
bus, the block has 2 EHCI blocks and 4 OHCI blocks. Change are to:
* Add files netlogic/xlp/usb-init.c and asm/netlogic/xlp-hal/usb.h
to initialize the USB controller and define PCI fixups. The PCI
fixups are to setup interrupts and DMA mask.
* Update include/asm/xlp-hal/{iomap.h,pic.h,xlp.h} to add interrupt
mapping for EHCI/OHCI interrupts.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3756/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds support for the XLP on-chip PCIe controller. On XLP, the
on-chip devices(including the 4 PCIe links) appear in the PCIe
configuration space of the XLP as PCI devices.
The changes are to initialize and register the PCIe controller,
enable hardware byte swap in the PCIe IO and MEM space, and to
enable PCIe interrupts.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3760/
Patchwork: https://patchwork.linux-mips.org/patch/4104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add platform code for XLR/XLS I2C controller and devices. Add
devices on the I2C bus on the XLR/XLS developement boards.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3757/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Changes to add support for the boot NOR flash on XLR boards and the
boot NAND/NOR flash drivers on the XLS boards.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3758/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add USB initialization code, setup resources and add USB platform
driver in mips/netlogic/xlr/platform.c.
Add USB support for XLR/XLS platform in Kconfig.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove NETLOGIC_ prefix from gpio register definitions, this will
bring it in-line with the other Netlogic headers.
Having NETLOGIC prefix here is misleading because these are XLR/XLS
specific register definitions.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update for core intialization code. Initialize status register
after receiving NMI for CPU wakeup. Add the low level L1D flush
code before enabling threads in core.
Also convert the ehb to _ehb so that it works under more GCC
versions.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3755/
Patchwork: https://patchwork.linux-mips.org/patch/4095/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No change in logic, comments update and whitespace cleanup.
* A few comments in the file were in assembler style and the rest
int C style, convert all of them to C style.
* Mark workarounds for Ax silicon with a macro XLP_AX_WORKAROUND
* Whitespace fixes - use tabs consistently
* rename __config_lsu macro to xlp_config_lsu
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3749/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Starting other threads in the core will change the number of
TLB entries of a CPU. Re-calculate current_cpu_data.tlbsize
on the boot cpu after enabling and waking up other threads.
The secondary CPUs do not need this logic because the threads
are enabled on the secondary cores at wakeup and before cpu_probe.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This has been obsolescent for a while; time for the final push.
In adjacent context, replaced old cpus_* with cpumask_*.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: David S. Miller <davem@davemloft.net> (arch/sparc)
Acked-by: Chris Metcalf <cmetcalf@tilera.com> (arch/tile)
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: sparclinux@vger.kernel.org
Netlogic XLR chip has multiple cores. Each core includes four integrated
hardware threads, and they share L1 data and instruction caches.
If the chip is marked to be SMT capable, scheduler then could do more, say,
idle load balancing.
Changes are now confined only to the code of XLR, and hardware is probed
to get core ID for correct setup.
[jayachandranc: simplified and adapted for new merged XLR/XLP code]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2972/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add new processor ID to asm/cpu.h and kernel/cpu-probe.c.
Update to new CPU frequency detection code which works on XLP 3XX
and 8XX.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2971/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Create a common NMI and reset handler in smpboot.S and use this for
both XLR and XLP. In the earlier code, the woken up CPUs would
busy wait until released, switch this to wakeup by NMI.
The initial wakeup code or XLR and XLP are differ since they are
started from different bootloaders (XLP from u-boot and XLR from
netlogic bootloader). But in both platforms the woken up CPUs wait
and are released by sending an NMI.
Add support for starting XLR and XLP in 1/2/4 threads per core.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2970/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
