fa16a5c13a
Support most of the LDO regulators in the twl4030 family chips. In the case of LDOs supporting MMC/SD, the voltage controls are used; but in most other cases, the regulator framework is only used to enable/disable a supplies, conserving power when a given voltage rail is not needed. The drivers/mfd/twl4030-core.c code already sets up the various regulators according to board-specific configuration, and knows that some chips don't provide the full set of voltage rails. The omitted regulators are intended to be under hardware control, such as during the hardware-mediated system powerup, powerdown, and suspend states. Unless/until software hooks are known to be safe, they won't be exported here. These regulators implement the new get_status() operation, but can't realistically implement get_mode(); the status output is effectively the result of a vote, with the relevant hardware inputs not exposed. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
402 lines
12 KiB
C
402 lines
12 KiB
C
/*
|
|
* twl4030.h - header for TWL4030 PM and audio CODEC device
|
|
*
|
|
* Copyright (C) 2005-2006 Texas Instruments, Inc.
|
|
*
|
|
* Based on tlv320aic23.c:
|
|
* Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*
|
|
*/
|
|
|
|
#ifndef __TWL4030_H_
|
|
#define __TWL4030_H_
|
|
|
|
/*
|
|
* Using the twl4030 core we address registers using a pair
|
|
* { module id, relative register offset }
|
|
* which that core then maps to the relevant
|
|
* { i2c slave, absolute register address }
|
|
*
|
|
* The module IDs are meaningful only to the twl4030 core code,
|
|
* which uses them as array indices to look up the first register
|
|
* address each module uses within a given i2c slave.
|
|
*/
|
|
|
|
/* Slave 0 (i2c address 0x48) */
|
|
#define TWL4030_MODULE_USB 0x00
|
|
|
|
/* Slave 1 (i2c address 0x49) */
|
|
#define TWL4030_MODULE_AUDIO_VOICE 0x01
|
|
#define TWL4030_MODULE_GPIO 0x02
|
|
#define TWL4030_MODULE_INTBR 0x03
|
|
#define TWL4030_MODULE_PIH 0x04
|
|
#define TWL4030_MODULE_TEST 0x05
|
|
|
|
/* Slave 2 (i2c address 0x4a) */
|
|
#define TWL4030_MODULE_KEYPAD 0x06
|
|
#define TWL4030_MODULE_MADC 0x07
|
|
#define TWL4030_MODULE_INTERRUPTS 0x08
|
|
#define TWL4030_MODULE_LED 0x09
|
|
#define TWL4030_MODULE_MAIN_CHARGE 0x0A
|
|
#define TWL4030_MODULE_PRECHARGE 0x0B
|
|
#define TWL4030_MODULE_PWM0 0x0C
|
|
#define TWL4030_MODULE_PWM1 0x0D
|
|
#define TWL4030_MODULE_PWMA 0x0E
|
|
#define TWL4030_MODULE_PWMB 0x0F
|
|
|
|
/* Slave 3 (i2c address 0x4b) */
|
|
#define TWL4030_MODULE_BACKUP 0x10
|
|
#define TWL4030_MODULE_INT 0x11
|
|
#define TWL4030_MODULE_PM_MASTER 0x12
|
|
#define TWL4030_MODULE_PM_RECEIVER 0x13
|
|
#define TWL4030_MODULE_RTC 0x14
|
|
#define TWL4030_MODULE_SECURED_REG 0x15
|
|
|
|
/*
|
|
* Read and write single 8-bit registers
|
|
*/
|
|
int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg);
|
|
int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg);
|
|
|
|
/*
|
|
* Read and write several 8-bit registers at once.
|
|
*
|
|
* IMPORTANT: For twl4030_i2c_write(), allocate num_bytes + 1
|
|
* for the value, and populate your data starting at offset 1.
|
|
*/
|
|
int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
|
|
int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/*
|
|
* NOTE: at up to 1024 registers, this is a big chip.
|
|
*
|
|
* Avoid putting register declarations in this file, instead of into
|
|
* a driver-private file, unless some of the registers in a block
|
|
* need to be shared with other drivers. One example is blocks that
|
|
* have Secondary IRQ Handler (SIH) registers.
|
|
*/
|
|
|
|
#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0)
|
|
#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1)
|
|
#define TWL4030_SIH_CTRL_COR_MASK BIT(2)
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/*
|
|
* GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
|
|
*/
|
|
|
|
#define REG_GPIODATAIN1 0x0
|
|
#define REG_GPIODATAIN2 0x1
|
|
#define REG_GPIODATAIN3 0x2
|
|
#define REG_GPIODATADIR1 0x3
|
|
#define REG_GPIODATADIR2 0x4
|
|
#define REG_GPIODATADIR3 0x5
|
|
#define REG_GPIODATAOUT1 0x6
|
|
#define REG_GPIODATAOUT2 0x7
|
|
#define REG_GPIODATAOUT3 0x8
|
|
#define REG_CLEARGPIODATAOUT1 0x9
|
|
#define REG_CLEARGPIODATAOUT2 0xA
|
|
#define REG_CLEARGPIODATAOUT3 0xB
|
|
#define REG_SETGPIODATAOUT1 0xC
|
|
#define REG_SETGPIODATAOUT2 0xD
|
|
#define REG_SETGPIODATAOUT3 0xE
|
|
#define REG_GPIO_DEBEN1 0xF
|
|
#define REG_GPIO_DEBEN2 0x10
|
|
#define REG_GPIO_DEBEN3 0x11
|
|
#define REG_GPIO_CTRL 0x12
|
|
#define REG_GPIOPUPDCTR1 0x13
|
|
#define REG_GPIOPUPDCTR2 0x14
|
|
#define REG_GPIOPUPDCTR3 0x15
|
|
#define REG_GPIOPUPDCTR4 0x16
|
|
#define REG_GPIOPUPDCTR5 0x17
|
|
#define REG_GPIO_ISR1A 0x19
|
|
#define REG_GPIO_ISR2A 0x1A
|
|
#define REG_GPIO_ISR3A 0x1B
|
|
#define REG_GPIO_IMR1A 0x1C
|
|
#define REG_GPIO_IMR2A 0x1D
|
|
#define REG_GPIO_IMR3A 0x1E
|
|
#define REG_GPIO_ISR1B 0x1F
|
|
#define REG_GPIO_ISR2B 0x20
|
|
#define REG_GPIO_ISR3B 0x21
|
|
#define REG_GPIO_IMR1B 0x22
|
|
#define REG_GPIO_IMR2B 0x23
|
|
#define REG_GPIO_IMR3B 0x24
|
|
#define REG_GPIO_EDR1 0x28
|
|
#define REG_GPIO_EDR2 0x29
|
|
#define REG_GPIO_EDR3 0x2A
|
|
#define REG_GPIO_EDR4 0x2B
|
|
#define REG_GPIO_EDR5 0x2C
|
|
#define REG_GPIO_SIH_CTRL 0x2D
|
|
|
|
/* Up to 18 signals are available as GPIOs, when their
|
|
* pins are not assigned to another use (such as ULPI/USB).
|
|
*/
|
|
#define TWL4030_GPIO_MAX 18
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/*
|
|
* Keypad register offsets (use TWL4030_MODULE_KEYPAD)
|
|
* ... SIH/interrupt only
|
|
*/
|
|
|
|
#define TWL4030_KEYPAD_KEYP_ISR1 0x11
|
|
#define TWL4030_KEYPAD_KEYP_IMR1 0x12
|
|
#define TWL4030_KEYPAD_KEYP_ISR2 0x13
|
|
#define TWL4030_KEYPAD_KEYP_IMR2 0x14
|
|
#define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */
|
|
#define TWL4030_KEYPAD_KEYP_EDR 0x16
|
|
#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/*
|
|
* Multichannel ADC register offsets (use TWL4030_MODULE_MADC)
|
|
* ... SIH/interrupt only
|
|
*/
|
|
|
|
#define TWL4030_MADC_ISR1 0x61
|
|
#define TWL4030_MADC_IMR1 0x62
|
|
#define TWL4030_MADC_ISR2 0x63
|
|
#define TWL4030_MADC_IMR2 0x64
|
|
#define TWL4030_MADC_SIR 0x65 /* test register */
|
|
#define TWL4030_MADC_EDR 0x66
|
|
#define TWL4030_MADC_SIH_CTRL 0x67
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/*
|
|
* Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS)
|
|
*/
|
|
|
|
#define TWL4030_INTERRUPTS_BCIISR1A 0x0
|
|
#define TWL4030_INTERRUPTS_BCIISR2A 0x1
|
|
#define TWL4030_INTERRUPTS_BCIIMR1A 0x2
|
|
#define TWL4030_INTERRUPTS_BCIIMR2A 0x3
|
|
#define TWL4030_INTERRUPTS_BCIISR1B 0x4
|
|
#define TWL4030_INTERRUPTS_BCIISR2B 0x5
|
|
#define TWL4030_INTERRUPTS_BCIIMR1B 0x6
|
|
#define TWL4030_INTERRUPTS_BCIIMR2B 0x7
|
|
#define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */
|
|
#define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */
|
|
#define TWL4030_INTERRUPTS_BCIEDR1 0xa
|
|
#define TWL4030_INTERRUPTS_BCIEDR2 0xb
|
|
#define TWL4030_INTERRUPTS_BCIEDR3 0xc
|
|
#define TWL4030_INTERRUPTS_BCISIHCTRL 0xd
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/*
|
|
* Power Interrupt block register offsets (use TWL4030_MODULE_INT)
|
|
*/
|
|
|
|
#define TWL4030_INT_PWR_ISR1 0x0
|
|
#define TWL4030_INT_PWR_IMR1 0x1
|
|
#define TWL4030_INT_PWR_ISR2 0x2
|
|
#define TWL4030_INT_PWR_IMR2 0x3
|
|
#define TWL4030_INT_PWR_SIR 0x4 /* test register */
|
|
#define TWL4030_INT_PWR_EDR1 0x5
|
|
#define TWL4030_INT_PWR_EDR2 0x6
|
|
#define TWL4030_INT_PWR_SIH_CTRL 0x7
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/* Power bus message definitions */
|
|
|
|
#define DEV_GRP_NULL 0x0
|
|
#define DEV_GRP_P1 0x1
|
|
#define DEV_GRP_P2 0x2
|
|
#define DEV_GRP_P3 0x4
|
|
|
|
#define RES_GRP_RES 0x0
|
|
#define RES_GRP_PP 0x1
|
|
#define RES_GRP_RC 0x2
|
|
#define RES_GRP_PP_RC 0x3
|
|
#define RES_GRP_PR 0x4
|
|
#define RES_GRP_PP_PR 0x5
|
|
#define RES_GRP_RC_PR 0x6
|
|
#define RES_GRP_ALL 0x7
|
|
|
|
#define RES_TYPE2_R0 0x0
|
|
|
|
#define RES_TYPE_ALL 0x7
|
|
|
|
#define RES_STATE_WRST 0xF
|
|
#define RES_STATE_ACTIVE 0xE
|
|
#define RES_STATE_SLEEP 0x8
|
|
#define RES_STATE_OFF 0x0
|
|
|
|
/*
|
|
* Power Bus Message Format ... these can be sent individually by Linux,
|
|
* but are usually part of downloaded scripts that are run when various
|
|
* power events are triggered.
|
|
*
|
|
* Broadcast Message (16 Bits):
|
|
* DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4]
|
|
* RES_STATE[3:0]
|
|
*
|
|
* Singular Message (16 Bits):
|
|
* DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
|
|
*/
|
|
|
|
#define MSG_BROADCAST(devgrp, grp, type, type2, state) \
|
|
( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \
|
|
| (type) << 4 | (state))
|
|
|
|
#define MSG_SINGULAR(devgrp, id, state) \
|
|
((devgrp) << 13 | 0 << 12 | (id) << 4 | (state))
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
struct twl4030_bci_platform_data {
|
|
int *battery_tmp_tbl;
|
|
unsigned int tblsize;
|
|
};
|
|
|
|
/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */
|
|
struct twl4030_gpio_platform_data {
|
|
int gpio_base;
|
|
unsigned irq_base, irq_end;
|
|
|
|
/* package the two LED signals as output-only GPIOs? */
|
|
bool use_leds;
|
|
|
|
/* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
|
|
u8 mmc_cd;
|
|
|
|
/* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */
|
|
u32 debounce;
|
|
|
|
/* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
|
|
* should be enabled. Else, if that bit is set in "pulldowns",
|
|
* that pulldown is enabled. Don't waste power by letting any
|
|
* digital inputs float...
|
|
*/
|
|
u32 pullups;
|
|
u32 pulldowns;
|
|
|
|
int (*setup)(struct device *dev,
|
|
unsigned gpio, unsigned ngpio);
|
|
int (*teardown)(struct device *dev,
|
|
unsigned gpio, unsigned ngpio);
|
|
};
|
|
|
|
struct twl4030_madc_platform_data {
|
|
int irq_line;
|
|
};
|
|
|
|
struct twl4030_keypad_data {
|
|
int rows;
|
|
int cols;
|
|
int *keymap;
|
|
int irq;
|
|
unsigned int keymapsize;
|
|
unsigned int rep:1;
|
|
};
|
|
|
|
enum twl4030_usb_mode {
|
|
T2_USB_MODE_ULPI = 1,
|
|
T2_USB_MODE_CEA2011_3PIN = 2,
|
|
};
|
|
|
|
struct twl4030_usb_data {
|
|
enum twl4030_usb_mode usb_mode;
|
|
};
|
|
|
|
struct twl4030_platform_data {
|
|
unsigned irq_base, irq_end;
|
|
struct twl4030_bci_platform_data *bci;
|
|
struct twl4030_gpio_platform_data *gpio;
|
|
struct twl4030_madc_platform_data *madc;
|
|
struct twl4030_keypad_data *keypad;
|
|
struct twl4030_usb_data *usb;
|
|
|
|
/* LDO regulators */
|
|
struct regulator_init_data *vdac;
|
|
struct regulator_init_data *vpll1;
|
|
struct regulator_init_data *vpll2;
|
|
struct regulator_init_data *vmmc1;
|
|
struct regulator_init_data *vmmc2;
|
|
struct regulator_init_data *vsim;
|
|
struct regulator_init_data *vaux1;
|
|
struct regulator_init_data *vaux2;
|
|
struct regulator_init_data *vaux3;
|
|
struct regulator_init_data *vaux4;
|
|
|
|
/* REVISIT more to come ... _nothing_ should be hard-wired */
|
|
};
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
int twl4030_sih_setup(int module);
|
|
|
|
/* Offsets to Power Registers */
|
|
#define TWL4030_VDAC_DEV_GRP 0x3B
|
|
#define TWL4030_VDAC_DEDICATED 0x3E
|
|
#define TWL4030_VAUX1_DEV_GRP 0x17
|
|
#define TWL4030_VAUX1_DEDICATED 0x1A
|
|
#define TWL4030_VAUX2_DEV_GRP 0x1B
|
|
#define TWL4030_VAUX2_DEDICATED 0x1E
|
|
#define TWL4030_VAUX3_DEV_GRP 0x1F
|
|
#define TWL4030_VAUX3_DEDICATED 0x22
|
|
|
|
|
|
#if defined(CONFIG_TWL4030_BCI_BATTERY) || \
|
|
defined(CONFIG_TWL4030_BCI_BATTERY_MODULE)
|
|
extern int twl4030charger_usb_en(int enable);
|
|
#else
|
|
static inline int twl4030charger_usb_en(int enable) { return 0; }
|
|
#endif
|
|
|
|
/*----------------------------------------------------------------------*/
|
|
|
|
/* Linux-specific regulator identifiers ... for now, we only support
|
|
* the LDOs, and leave the three buck converters alone. VDD1 and VDD2
|
|
* need to tie into hardware based voltage scaling (cpufreq etc), while
|
|
* VIO is generally fixed.
|
|
*/
|
|
|
|
/* EXTERNAL dc-to-dc buck converters */
|
|
#define TWL4030_REG_VDD1 0
|
|
#define TWL4030_REG_VDD2 1
|
|
#define TWL4030_REG_VIO 2
|
|
|
|
/* EXTERNAL LDOs */
|
|
#define TWL4030_REG_VDAC 3
|
|
#define TWL4030_REG_VPLL1 4
|
|
#define TWL4030_REG_VPLL2 5 /* not on all chips */
|
|
#define TWL4030_REG_VMMC1 6
|
|
#define TWL4030_REG_VMMC2 7 /* not on all chips */
|
|
#define TWL4030_REG_VSIM 8 /* not on all chips */
|
|
#define TWL4030_REG_VAUX1 9 /* not on all chips */
|
|
#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */
|
|
#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */
|
|
#define TWL4030_REG_VAUX3 12 /* not on all chips */
|
|
#define TWL4030_REG_VAUX4 13 /* not on all chips */
|
|
|
|
/* INTERNAL LDOs */
|
|
#define TWL4030_REG_VINTANA1 14
|
|
#define TWL4030_REG_VINTANA2 15
|
|
#define TWL4030_REG_VINTDIG 16
|
|
#define TWL4030_REG_VUSB1V5 17
|
|
#define TWL4030_REG_VUSB1V8 18
|
|
#define TWL4030_REG_VUSB3V1 19
|
|
|
|
#endif /* End of __TWL4030_H */
|