e955cead03
This core is found on some Freescale SoCs and also some Coldfire SoCs. Support for Coldfire is missing though at the moment as they have an older revision of the core which does not have RX FIFO support. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
101 lines
3 KiB
Text
101 lines
3 KiB
Text
menu "CAN Device Drivers"
|
|
depends on CAN
|
|
|
|
config CAN_VCAN
|
|
tristate "Virtual Local CAN Interface (vcan)"
|
|
depends on CAN
|
|
default N
|
|
---help---
|
|
Similar to the network loopback devices, vcan offers a
|
|
virtual local CAN interface.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called vcan.
|
|
|
|
config CAN_DEV
|
|
tristate "Platform CAN drivers with Netlink support"
|
|
depends on CAN
|
|
default Y
|
|
---help---
|
|
Enables the common framework for platform CAN drivers with Netlink
|
|
support. This is the standard library for CAN drivers.
|
|
If unsure, say Y.
|
|
|
|
config CAN_CALC_BITTIMING
|
|
bool "CAN bit-timing calculation"
|
|
depends on CAN_DEV
|
|
default Y
|
|
---help---
|
|
If enabled, CAN bit-timing parameters will be calculated for the
|
|
bit-rate specified via Netlink argument "bitrate" when the device
|
|
get started. This works fine for the most common CAN controllers
|
|
with standard bit-rates but may fail for exotic bit-rates or CAN
|
|
source clock frequencies. Disabling saves some space, but then the
|
|
bit-timing parameters must be specified directly using the Netlink
|
|
arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
|
|
If unsure, say Y.
|
|
|
|
config CAN_AT91
|
|
tristate "Atmel AT91 onchip CAN controller"
|
|
depends on CAN_DEV && ARCH_AT91SAM9263
|
|
---help---
|
|
This is a driver for the SoC CAN controller in Atmel's AT91SAM9263.
|
|
|
|
config CAN_TI_HECC
|
|
depends on CAN_DEV && ARCH_OMAP3
|
|
tristate "TI High End CAN Controller"
|
|
---help---
|
|
Driver for TI HECC (High End CAN Controller) module found on many
|
|
TI devices. The device specifications are available from www.ti.com
|
|
|
|
config CAN_MCP251X
|
|
tristate "Microchip MCP251x SPI CAN controllers"
|
|
depends on CAN_DEV && SPI && HAS_DMA
|
|
---help---
|
|
Driver for the Microchip MCP251x SPI CAN controllers.
|
|
|
|
config CAN_BFIN
|
|
depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x)
|
|
tristate "Analog Devices Blackfin on-chip CAN"
|
|
---help---
|
|
Driver for the Analog Devices Blackfin on-chip CAN controllers
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called bfin_can.
|
|
|
|
config CAN_JANZ_ICAN3
|
|
tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
|
|
depends on CAN_DEV && MFD_JANZ_CMODIO
|
|
---help---
|
|
Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
|
|
connects to a MODULbus carrier board.
|
|
|
|
This driver can also be built as a module. If so, the module will be
|
|
called janz-ican3.ko.
|
|
|
|
config HAVE_CAN_FLEXCAN
|
|
bool
|
|
|
|
config CAN_FLEXCAN
|
|
tristate "Support for Freescale FLEXCAN based chips"
|
|
depends on CAN_DEV && HAVE_CAN_FLEXCAN
|
|
---help---
|
|
Say Y here if you want to support for Freescale FlexCAN.
|
|
|
|
source "drivers/net/can/mscan/Kconfig"
|
|
|
|
source "drivers/net/can/sja1000/Kconfig"
|
|
|
|
source "drivers/net/can/usb/Kconfig"
|
|
|
|
config CAN_DEBUG_DEVICES
|
|
bool "CAN devices debugging messages"
|
|
depends on CAN
|
|
default N
|
|
---help---
|
|
Say Y here if you want the CAN device drivers to produce a bunch of
|
|
debug messages to the system log. Select this if you are having
|
|
a problem with CAN support and want to see more of what is going
|
|
on.
|
|
|
|
endmenu
|