9c75fc8c5c
These old drivers are not used anymore, we use the ones in drivers/rtc. This allows us to remove some cruft in the CRIS timekeeping code. Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
319 lines
8.5 KiB
C
319 lines
8.5 KiB
C
/*
|
|
* linux/arch/cris/arch-v32/kernel/time.c
|
|
*
|
|
* Copyright (C) 2003-2010 Axis Communications AB
|
|
*
|
|
*/
|
|
|
|
#include <linux/timex.h>
|
|
#include <linux/time.h>
|
|
#include <linux/clocksource.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/swap.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/init.h>
|
|
#include <linux/threads.h>
|
|
#include <linux/cpufreq.h>
|
|
#include <asm/types.h>
|
|
#include <asm/signal.h>
|
|
#include <asm/io.h>
|
|
#include <asm/delay.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/irq_regs.h>
|
|
|
|
#include <hwregs/reg_map.h>
|
|
#include <hwregs/reg_rdwr.h>
|
|
#include <hwregs/timer_defs.h>
|
|
#include <hwregs/intr_vect_defs.h>
|
|
#ifdef CONFIG_CRIS_MACH_ARTPEC3
|
|
#include <hwregs/clkgen_defs.h>
|
|
#endif
|
|
|
|
/* Watchdog defines */
|
|
#define ETRAX_WD_KEY_MASK 0x7F /* key is 7 bit */
|
|
#define ETRAX_WD_HZ 763 /* watchdog counts at 763 Hz */
|
|
/* Number of 763 counts before watchdog bites */
|
|
#define ETRAX_WD_CNT ((2*ETRAX_WD_HZ)/HZ + 1)
|
|
|
|
/* Register the continuos readonly timer available in FS and ARTPEC-3. */
|
|
static cycle_t read_cont_rotime(struct clocksource *cs)
|
|
{
|
|
return (u32)REG_RD(timer, regi_timer0, r_time);
|
|
}
|
|
|
|
static struct clocksource cont_rotime = {
|
|
.name = "crisv32_rotime",
|
|
.rating = 300,
|
|
.read = read_cont_rotime,
|
|
.mask = CLOCKSOURCE_MASK(32),
|
|
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
|
|
};
|
|
|
|
static int __init etrax_init_cont_rotime(void)
|
|
{
|
|
clocksource_register_khz(&cont_rotime, 100000);
|
|
return 0;
|
|
}
|
|
arch_initcall(etrax_init_cont_rotime);
|
|
|
|
|
|
unsigned long timer_regs[NR_CPUS] =
|
|
{
|
|
regi_timer0,
|
|
#ifdef CONFIG_SMP
|
|
regi_timer2
|
|
#endif
|
|
};
|
|
|
|
extern int set_rtc_mmss(unsigned long nowtime);
|
|
|
|
#ifdef CONFIG_CPU_FREQ
|
|
static int
|
|
cris_time_freq_notifier(struct notifier_block *nb, unsigned long val,
|
|
void *data);
|
|
|
|
static struct notifier_block cris_time_freq_notifier_block = {
|
|
.notifier_call = cris_time_freq_notifier,
|
|
};
|
|
#endif
|
|
|
|
unsigned long get_ns_in_jiffie(void)
|
|
{
|
|
reg_timer_r_tmr0_data data;
|
|
unsigned long ns;
|
|
|
|
data = REG_RD(timer, regi_timer0, r_tmr0_data);
|
|
ns = (TIMER0_DIV - data) * 10;
|
|
return ns;
|
|
}
|
|
|
|
|
|
/* From timer MDS describing the hardware watchdog:
|
|
* 4.3.1 Watchdog Operation
|
|
* The watchdog timer is an 8-bit timer with a configurable start value.
|
|
* Once started the watchdog counts downwards with a frequency of 763 Hz
|
|
* (100/131072 MHz). When the watchdog counts down to 1, it generates an
|
|
* NMI (Non Maskable Interrupt), and when it counts down to 0, it resets the
|
|
* chip.
|
|
*/
|
|
/* This gives us 1.3 ms to do something useful when the NMI comes */
|
|
|
|
/* Right now, starting the watchdog is the same as resetting it */
|
|
#define start_watchdog reset_watchdog
|
|
|
|
#if defined(CONFIG_ETRAX_WATCHDOG)
|
|
static short int watchdog_key = 42; /* arbitrary 7 bit number */
|
|
#endif
|
|
|
|
/* Number of pages to consider "out of memory". It is normal that the memory
|
|
* is used though, so set this really low. */
|
|
#define WATCHDOG_MIN_FREE_PAGES 8
|
|
|
|
void reset_watchdog(void)
|
|
{
|
|
#if defined(CONFIG_ETRAX_WATCHDOG)
|
|
reg_timer_rw_wd_ctrl wd_ctrl = { 0 };
|
|
|
|
/* Only keep watchdog happy as long as we have memory left! */
|
|
if(nr_free_pages() > WATCHDOG_MIN_FREE_PAGES) {
|
|
/* Reset the watchdog with the inverse of the old key */
|
|
/* Invert key, which is 7 bits */
|
|
watchdog_key ^= ETRAX_WD_KEY_MASK;
|
|
wd_ctrl.cnt = ETRAX_WD_CNT;
|
|
wd_ctrl.cmd = regk_timer_start;
|
|
wd_ctrl.key = watchdog_key;
|
|
REG_WR(timer, regi_timer0, rw_wd_ctrl, wd_ctrl);
|
|
}
|
|
#endif
|
|
}
|
|
|
|
/* stop the watchdog - we still need the correct key */
|
|
|
|
void stop_watchdog(void)
|
|
{
|
|
#if defined(CONFIG_ETRAX_WATCHDOG)
|
|
reg_timer_rw_wd_ctrl wd_ctrl = { 0 };
|
|
watchdog_key ^= ETRAX_WD_KEY_MASK; /* invert key, which is 7 bits */
|
|
wd_ctrl.cnt = ETRAX_WD_CNT;
|
|
wd_ctrl.cmd = regk_timer_stop;
|
|
wd_ctrl.key = watchdog_key;
|
|
REG_WR(timer, regi_timer0, rw_wd_ctrl, wd_ctrl);
|
|
#endif
|
|
}
|
|
|
|
extern void show_registers(struct pt_regs *regs);
|
|
|
|
void handle_watchdog_bite(struct pt_regs *regs)
|
|
{
|
|
#if defined(CONFIG_ETRAX_WATCHDOG)
|
|
extern int cause_of_death;
|
|
|
|
oops_in_progress = 1;
|
|
printk(KERN_WARNING "Watchdog bite\n");
|
|
|
|
/* Check if forced restart or unexpected watchdog */
|
|
if (cause_of_death == 0xbedead) {
|
|
#ifdef CONFIG_CRIS_MACH_ARTPEC3
|
|
/* There is a bug in Artpec-3 (voodoo TR 78) that requires
|
|
* us to go to lower frequency for the reset to be reliable
|
|
*/
|
|
reg_clkgen_rw_clk_ctrl ctrl =
|
|
REG_RD(clkgen, regi_clkgen, rw_clk_ctrl);
|
|
ctrl.pll = 0;
|
|
REG_WR(clkgen, regi_clkgen, rw_clk_ctrl, ctrl);
|
|
#endif
|
|
while(1);
|
|
}
|
|
|
|
/* Unexpected watchdog, stop the watchdog and dump registers. */
|
|
stop_watchdog();
|
|
printk(KERN_WARNING "Oops: bitten by watchdog\n");
|
|
show_registers(regs);
|
|
oops_in_progress = 0;
|
|
#ifndef CONFIG_ETRAX_WATCHDOG_NICE_DOGGY
|
|
reset_watchdog();
|
|
#endif
|
|
while(1) /* nothing */;
|
|
#endif
|
|
}
|
|
|
|
/*
|
|
* timer_interrupt() needs to keep up the real-time clock,
|
|
* as well as call the "xtime_update()" routine every clocktick.
|
|
*/
|
|
extern void cris_do_profile(struct pt_regs *regs);
|
|
|
|
static inline irqreturn_t timer_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct pt_regs *regs = get_irq_regs();
|
|
int cpu = smp_processor_id();
|
|
reg_timer_r_masked_intr masked_intr;
|
|
reg_timer_rw_ack_intr ack_intr = { 0 };
|
|
|
|
/* Check if the timer interrupt is for us (a tmr0 int) */
|
|
masked_intr = REG_RD(timer, timer_regs[cpu], r_masked_intr);
|
|
if (!masked_intr.tmr0)
|
|
return IRQ_NONE;
|
|
|
|
/* Acknowledge the timer irq. */
|
|
ack_intr.tmr0 = 1;
|
|
REG_WR(timer, timer_regs[cpu], rw_ack_intr, ack_intr);
|
|
|
|
/* Reset watchdog otherwise it resets us! */
|
|
reset_watchdog();
|
|
|
|
/* Update statistics. */
|
|
update_process_times(user_mode(regs));
|
|
|
|
cris_do_profile(regs); /* Save profiling information */
|
|
|
|
/* The master CPU is responsible for the time keeping. */
|
|
if (cpu != 0)
|
|
return IRQ_HANDLED;
|
|
|
|
/* Call the real timer interrupt handler */
|
|
xtime_update(1);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
/* Timer is IRQF_SHARED so drivers can add stuff to the timer irq chain.
|
|
* It needs to be IRQF_DISABLED to make the jiffies update work properly.
|
|
*/
|
|
static struct irqaction irq_timer = {
|
|
.handler = timer_interrupt,
|
|
.flags = IRQF_SHARED | IRQF_DISABLED,
|
|
.name = "timer"
|
|
};
|
|
|
|
void __init cris_timer_init(void)
|
|
{
|
|
int cpu = smp_processor_id();
|
|
reg_timer_rw_tmr0_ctrl tmr0_ctrl = { 0 };
|
|
reg_timer_rw_tmr0_div tmr0_div = TIMER0_DIV;
|
|
reg_timer_rw_intr_mask timer_intr_mask;
|
|
|
|
/* Setup the etrax timers.
|
|
* Base frequency is 100MHz, divider 1000000 -> 100 HZ
|
|
* We use timer0, so timer1 is free.
|
|
* The trig timer is used by the fasttimer API if enabled.
|
|
*/
|
|
|
|
tmr0_ctrl.op = regk_timer_ld;
|
|
tmr0_ctrl.freq = regk_timer_f100;
|
|
REG_WR(timer, timer_regs[cpu], rw_tmr0_div, tmr0_div);
|
|
REG_WR(timer, timer_regs[cpu], rw_tmr0_ctrl, tmr0_ctrl); /* Load */
|
|
tmr0_ctrl.op = regk_timer_run;
|
|
REG_WR(timer, timer_regs[cpu], rw_tmr0_ctrl, tmr0_ctrl); /* Start */
|
|
|
|
/* Enable the timer irq. */
|
|
timer_intr_mask = REG_RD(timer, timer_regs[cpu], rw_intr_mask);
|
|
timer_intr_mask.tmr0 = 1;
|
|
REG_WR(timer, timer_regs[cpu], rw_intr_mask, timer_intr_mask);
|
|
}
|
|
|
|
void __init time_init(void)
|
|
{
|
|
reg_intr_vect_rw_mask intr_mask;
|
|
|
|
/* Probe for the RTC and read it if it exists.
|
|
* Before the RTC can be probed the loops_per_usec variable needs
|
|
* to be initialized to make usleep work. A better value for
|
|
* loops_per_usec is calculated by the kernel later once the
|
|
* clock has started.
|
|
*/
|
|
loops_per_usec = 50;
|
|
|
|
/* Start CPU local timer. */
|
|
cris_timer_init();
|
|
|
|
/* Enable the timer irq in global config. */
|
|
intr_mask = REG_RD_VECT(intr_vect, regi_irq, rw_mask, 1);
|
|
intr_mask.timer0 = 1;
|
|
REG_WR_VECT(intr_vect, regi_irq, rw_mask, 1, intr_mask);
|
|
|
|
/* Now actually register the timer irq handler that calls
|
|
* timer_interrupt(). */
|
|
setup_irq(TIMER0_INTR_VECT, &irq_timer);
|
|
|
|
/* Enable watchdog if we should use one. */
|
|
|
|
#if defined(CONFIG_ETRAX_WATCHDOG)
|
|
printk(KERN_INFO "Enabling watchdog...\n");
|
|
start_watchdog();
|
|
|
|
/* If we use the hardware watchdog, we want to trap it as an NMI
|
|
* and dump registers before it resets us. For this to happen, we
|
|
* must set the "m" NMI enable flag (which once set, is unset only
|
|
* when an NMI is taken). */
|
|
{
|
|
unsigned long flags;
|
|
local_save_flags(flags);
|
|
flags |= (1<<30); /* NMI M flag is at bit 30 */
|
|
local_irq_restore(flags);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_CPU_FREQ
|
|
cpufreq_register_notifier(&cris_time_freq_notifier_block,
|
|
CPUFREQ_TRANSITION_NOTIFIER);
|
|
#endif
|
|
}
|
|
|
|
#ifdef CONFIG_CPU_FREQ
|
|
static int
|
|
cris_time_freq_notifier(struct notifier_block *nb, unsigned long val,
|
|
void *data)
|
|
{
|
|
struct cpufreq_freqs *freqs = data;
|
|
if (val == CPUFREQ_POSTCHANGE) {
|
|
reg_timer_r_tmr0_data data;
|
|
reg_timer_rw_tmr0_div div = (freqs->new * 500) / HZ;
|
|
do {
|
|
data = REG_RD(timer, timer_regs[freqs->cpu],
|
|
r_tmr0_data);
|
|
} while (data > 20);
|
|
REG_WR(timer, timer_regs[freqs->cpu], rw_tmr0_div, div);
|
|
}
|
|
return 0;
|
|
}
|
|
#endif
|