Techwizz/kernel-fxtec-pro1x
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
kernel-fxtec-pro1x/arch/powerpc/platforms/Kconfig
Anatolij Gustschin e39d5ef678 powerpc/5xxx: extend mpc8xxx_gpio driver to support mpc512x gpios 
The GPIO controller of MPC512x is slightly different from
8xxx GPIO controllers. The register interface is the same
except the external interrupt control register. The MPC512x
GPIO controller differentiates between four interrupt event
types and therefore provides two interrupt control registers,
GPICR1 and GPICR2. GPIO[0:15] interrupt event types are
configured in GPICR1 register, GPIO[16:31] - in GPICR2 register.

This patch adds MPC512x speciffic set_type() callback and
updates config file and comments. Additionally the gpio chip
registration function is changed to use for_each_matching_node()
preventing multiple registration if a node claimes compatibility
with another gpio controller type.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-09-10 13:31:16 -06:00

342 lines
9.2 KiB
Text
Raw Blame History

menu "Platform support"
source "arch/powerpc/platforms/pseries/Kconfig"
source "arch/powerpc/platforms/iseries/Kconfig"
source "arch/powerpc/platforms/chrp/Kconfig"
source "arch/powerpc/platforms/512x/Kconfig"
source "arch/powerpc/platforms/52xx/Kconfig"
source "arch/powerpc/platforms/powermac/Kconfig"
source "arch/powerpc/platforms/prep/Kconfig"
source "arch/powerpc/platforms/maple/Kconfig"
source "arch/powerpc/platforms/pasemi/Kconfig"
source "arch/powerpc/platforms/ps3/Kconfig"
source "arch/powerpc/platforms/cell/Kconfig"
source "arch/powerpc/platforms/8xx/Kconfig"
source "arch/powerpc/platforms/82xx/Kconfig"
source "arch/powerpc/platforms/83xx/Kconfig"
source "arch/powerpc/platforms/85xx/Kconfig"
source "arch/powerpc/platforms/86xx/Kconfig"
source "arch/powerpc/platforms/embedded6xx/Kconfig"
source "arch/powerpc/platforms/44x/Kconfig"
source "arch/powerpc/platforms/40x/Kconfig"
source "arch/powerpc/platforms/amigaone/Kconfig"
config PPC_NATIVE
bool
depends on 6xx || PPC64
help
Support for running natively on the hardware, i.e. without
a hypervisor. This option is not user-selectable but should
be selected by all platforms that need it.
config PPC_OF_BOOT_TRAMPOLINE
bool "Support booting from Open Firmware or yaboot"
depends on 6xx || PPC64
default y
help
Support from booting from Open Firmware or yaboot using an
Open Firmware client interface. This enables the kernel to
communicate with open firmware to retrieve system informations
such as the device tree.
In case of doubt, say Y
config UDBG_RTAS_CONSOLE
bool "RTAS based debug console"
depends on PPC_RTAS
default n
config PPC_UDBG_BEAT
bool "BEAT based debug console"
depends on PPC_CELLEB
default n
config XICS
depends on PPC_PSERIES
bool
default y
config IPIC
bool
default n
config MPIC
bool
default n
config MPIC_WEIRD
bool
default n
config PPC_I8259
bool
default n
config U3_DART
bool
depends on PPC64
default n
config PPC_RTAS
bool
default n
config RTAS_ERROR_LOGGING
bool
depends on PPC_RTAS
default n
config PPC_RTAS_DAEMON
bool
depends on PPC_RTAS
default n
config RTAS_PROC
bool "Proc interface to RTAS"
depends on PPC_RTAS
default y
config RTAS_FLASH
tristate "Firmware flash interface"
depends on PPC64 && RTAS_PROC
config MMIO_NVRAM
bool
default n
config MPIC_U3_HT_IRQS
bool
depends on PPC_MAPLE
default y
config MPIC_BROKEN_REGREAD
bool
depends on MPIC
help
This option enables a MPIC driver workaround for some chips
that have a bug that causes some interrupt source information
to not read back properly. It is safe to use on other chips as
well, but enabling it uses about 8KB of memory to keep copies
of the register contents in software.
config IBMVIO
depends on PPC_PSERIES || PPC_ISERIES
bool
default y
config IBMEBUS
depends on PPC_PSERIES
bool "Support for GX bus based adapters"
help
Bus device driver for GX bus based adapters.
config PPC_MPC106
bool
default n
config PPC_970_NAP
bool
default n
config PPC_INDIRECT_IO
bool
select GENERIC_IOMAP
default n
config GENERIC_IOMAP
bool
default n
source "drivers/cpufreq/Kconfig"
menu "CPU Frequency drivers"
depends on CPU_FREQ
config CPU_FREQ_PMAC
bool "Support for Apple PowerBooks"
depends on ADB_PMU && PPC32
select CPU_FREQ_TABLE
help
This adds support for frequency switching on Apple PowerBooks,
this currently includes some models of iBook & Titanium
PowerBook.
config CPU_FREQ_PMAC64
bool "Support for some Apple G5s"
depends on PPC_PMAC && PPC64
select CPU_FREQ_TABLE
help
This adds support for frequency switching on Apple iMac G5,
and some of the more recent desktop G5 machines as well.
config PPC_PASEMI_CPUFREQ
bool "Support for PA Semi PWRficient"
depends on PPC_PASEMI
default y
select CPU_FREQ_TABLE
help
This adds the support for frequency switching on PA Semi
PWRficient processors.
endmenu
config PPC601_SYNC_FIX
bool "Workarounds for PPC601 bugs"
depends on 6xx && (PPC_PREP || PPC_PMAC)
help
Some versions of the PPC601 (the first PowerPC chip) have bugs which
mean that extra synchronization instructions are required near
certain instructions, typically those that make major changes to the
CPU state. These extra instructions reduce performance slightly.
If you say N here, these extra instructions will not be included,
resulting in a kernel which will run faster but may not run at all
on some systems with the PPC601 chip.
If in doubt, say Y here.
config TAU
bool "On-chip CPU temperature sensor support"
depends on 6xx
help
G3 and G4 processors have an on-chip temperature sensor called the
'Thermal Assist Unit (TAU)', which, in theory, can measure the on-die
temperature within 2-4 degrees Celsius. This option shows the current
on-die temperature in /proc/cpuinfo if the cpu supports it.
Unfortunately, on some chip revisions, this sensor is very inaccurate
and in many cases, does not work at all, so don't assume the cpu
temp is actually what /proc/cpuinfo says it is.
config TAU_INT
bool "Interrupt driven TAU driver (DANGEROUS)"
depends on TAU
---help---
The TAU supports an interrupt driven mode which causes an interrupt
whenever the temperature goes out of range. This is the fastest way
to get notified the temp has exceeded a range. With this option off,
a timer is used to re-check the temperature periodically.
However, on some cpus it appears that the TAU interrupt hardware
is buggy and can cause a situation which would lead unexplained hard
lockups.
Unless you are extending the TAU driver, or enjoy kernel/hardware
debugging, leave this option off.
config TAU_AVERAGE
bool "Average high and low temp"
depends on TAU
---help---
The TAU hardware can compare the temperature to an upper and lower
bound. The default behavior is to show both the upper and lower
bound in /proc/cpuinfo. If the range is large, the temperature is
either changing a lot, or the TAU hardware is broken (likely on some
G4's). If the range is small (around 4 degrees), the temperature is
relatively stable. If you say Y here, a single temperature value,
halfway between the upper and lower bounds, will be reported in
/proc/cpuinfo.
If in doubt, say N here.
config QUICC_ENGINE
bool "Freescale QUICC Engine (QE) Support"
depends on FSL_SOC
select PPC_LIB_RHEAP
select CRC32
help
The QUICC Engine (QE) is a new generation of communications
coprocessors on Freescale embedded CPUs (akin to CPM in older chips).
Selecting this option means that you wish to build a kernel
for a machine with a QE coprocessor.
config QE_GPIO
bool "QE GPIO support"
depends on QUICC_ENGINE
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
help
Say Y here if you're going to use hardware that connects to the
QE GPIOs.
config CPM2
bool "Enable support for the CPM2 (Communications Processor Module)"
depends on (FSL_SOC_BOOKE && PPC32) || 8260
select CPM
select PPC_LIB_RHEAP
select PPC_PCI_CHOICE
select ARCH_REQUIRE_GPIOLIB
select GENERIC_GPIO
help
The CPM2 (Communications Processor Module) is a coprocessor on
embedded CPUs made by Freescale. Selecting this option means that
you wish to build a kernel for a machine with a CPM2 coprocessor
on it (826x, 827x, 8560).
config AXON_RAM
tristate "Axon DDR2 memory device driver"
depends on PPC_IBM_CELL_BLADE && BLOCK
default m
help
It registers one block device per Axon's DDR2 memory bank found
on a system. Block devices are called axonram?, their major and
minor numbers are available in /proc/devices, /proc/partitions or
in /sys/block/axonram?/dev.
config FSL_ULI1575
bool
default n
select GENERIC_ISA_DMA
help
Supports for the ULI1575 PCIe south bridge that exists on some
Freescale reference boards. The boards all use the ULI in pretty
much the same way.
config CPM
bool
select PPC_CLOCK
config OF_RTC
bool
help
Uses information from the OF or flattened device tree to instantiate
platform devices for direct mapped RTC chips like the DS1742 or DS1743.
source "arch/powerpc/sysdev/bestcomm/Kconfig"
config MPC8xxx_GPIO
bool "MPC512x/MPC8xxx GPIO support"
depends on PPC_MPC512x || PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || \
FSL_SOC_BOOKE || PPC_86xx
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
help
Say Y here if you're going to use hardware that connects to the
MPC512x/831x/834x/837x/8572/8610 GPIOs.
config SIMPLE_GPIO
bool "Support for simple, memory-mapped GPIO controllers"
depends on PPC
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
help
Say Y here to support simple, memory-mapped GPIO controllers.
These are usually BCSRs used to control board's switches, LEDs,
chip-selects, Ethernet/USB PHY's power and various other small
on-board peripherals.
config MCU_MPC8349EMITX
tristate "MPC8349E-mITX MCU driver"
depends on I2C && PPC_83xx
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
help
Say Y here to enable soft power-off functionality on the Freescale
boards with the MPC8349E-mITX-compatible MCU chips. This driver will
also register MCU GPIOs with the generic GPIO API, so you'll able
to use MCU pins as GPIOs.
config XILINX_PCI
bool "Xilinx PCI host bridge support"
depends on PCI && XILINX_VIRTEX
endmenu
Reference in a new issue View git blame Copy permalink