1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
169 lines
5.5 KiB
C
169 lines
5.5 KiB
C
/**************************************************
|
|
* *
|
|
* Definition of D-Link Ethernet Pocket adapter *
|
|
* *
|
|
**************************************************/
|
|
/*
|
|
* D-Link Ethernet pocket adapter ports
|
|
*/
|
|
/*
|
|
* OK, so I'm cheating, but there are an awful lot of
|
|
* reads and writes in order to get anything in and out
|
|
* of the DE-600 with 4 bits at a time in the parallel port,
|
|
* so every saved instruction really helps :-)
|
|
*/
|
|
|
|
#ifndef DE600_IO
|
|
#define DE600_IO 0x378
|
|
#endif
|
|
|
|
#define DATA_PORT (DE600_IO)
|
|
#define STATUS_PORT (DE600_IO + 1)
|
|
#define COMMAND_PORT (DE600_IO + 2)
|
|
|
|
#ifndef DE600_IRQ
|
|
#define DE600_IRQ 7
|
|
#endif
|
|
/*
|
|
* It really should look like this, and autoprobing as well...
|
|
*
|
|
#define DATA_PORT (dev->base_addr + 0)
|
|
#define STATUS_PORT (dev->base_addr + 1)
|
|
#define COMMAND_PORT (dev->base_addr + 2)
|
|
#define DE600_IRQ dev->irq
|
|
*/
|
|
|
|
/*
|
|
* D-Link COMMAND_PORT commands
|
|
*/
|
|
#define SELECT_NIC 0x04 /* select Network Interface Card */
|
|
#define SELECT_PRN 0x1c /* select Printer */
|
|
#define NML_PRN 0xec /* normal Printer situation */
|
|
#define IRQEN 0x10 /* enable IRQ line */
|
|
|
|
/*
|
|
* D-Link STATUS_PORT
|
|
*/
|
|
#define RX_BUSY 0x80
|
|
#define RX_GOOD 0x40
|
|
#define TX_FAILED16 0x10
|
|
#define TX_BUSY 0x08
|
|
|
|
/*
|
|
* D-Link DATA_PORT commands
|
|
* command in low 4 bits
|
|
* data in high 4 bits
|
|
* select current data nibble with HI_NIBBLE bit
|
|
*/
|
|
#define WRITE_DATA 0x00 /* write memory */
|
|
#define READ_DATA 0x01 /* read memory */
|
|
#define STATUS 0x02 /* read status register */
|
|
#define COMMAND 0x03 /* write command register (see COMMAND below) */
|
|
#define NULL_COMMAND 0x04 /* null command */
|
|
#define RX_LEN 0x05 /* read received packet length */
|
|
#define TX_ADDR 0x06 /* set adapter transmit memory address */
|
|
#define RW_ADDR 0x07 /* set adapter read/write memory address */
|
|
#define HI_NIBBLE 0x08 /* read/write the high nibble of data,
|
|
or-ed with rest of command */
|
|
|
|
/*
|
|
* command register, accessed through DATA_PORT with low bits = COMMAND
|
|
*/
|
|
#define RX_ALL 0x01 /* PROMISCUOUS */
|
|
#define RX_BP 0x02 /* default: BROADCAST & PHYSICAL ADDRESS */
|
|
#define RX_MBP 0x03 /* MULTICAST, BROADCAST & PHYSICAL ADDRESS */
|
|
|
|
#define TX_ENABLE 0x04 /* bit 2 */
|
|
#define RX_ENABLE 0x08 /* bit 3 */
|
|
|
|
#define RESET 0x80 /* set bit 7 high */
|
|
#define STOP_RESET 0x00 /* set bit 7 low */
|
|
|
|
/*
|
|
* data to command register
|
|
* (high 4 bits in write to DATA_PORT)
|
|
*/
|
|
#define RX_PAGE2_SELECT 0x10 /* bit 4, only 2 pages to select */
|
|
#define RX_BASE_PAGE 0x20 /* bit 5, always set when specifying RX_ADDR */
|
|
#define FLIP_IRQ 0x40 /* bit 6 */
|
|
|
|
/*
|
|
* D-Link adapter internal memory:
|
|
*
|
|
* 0-2K 1:st transmit page (send from pointer up to 2K)
|
|
* 2-4K 2:nd transmit page (send from pointer up to 4K)
|
|
*
|
|
* 4-6K 1:st receive page (data from 4K upwards)
|
|
* 6-8K 2:nd receive page (data from 6K upwards)
|
|
*
|
|
* 8K+ Adapter ROM (contains magic code and last 3 bytes of Ethernet address)
|
|
*/
|
|
#define MEM_2K 0x0800 /* 2048 */
|
|
#define MEM_4K 0x1000 /* 4096 */
|
|
#define MEM_6K 0x1800 /* 6144 */
|
|
#define NODE_ADDRESS 0x2000 /* 8192 */
|
|
|
|
#define RUNT 60 /* Too small Ethernet packet */
|
|
|
|
/**************************************************
|
|
* *
|
|
* End of definition *
|
|
* *
|
|
**************************************************/
|
|
|
|
/*
|
|
* Index to functions, as function prototypes.
|
|
*/
|
|
/* Routines used internally. (See "convenience macros") */
|
|
static u8 de600_read_status(struct net_device *dev);
|
|
static u8 de600_read_byte(unsigned char type, struct net_device *dev);
|
|
|
|
/* Put in the device structure. */
|
|
static int de600_open(struct net_device *dev);
|
|
static int de600_close(struct net_device *dev);
|
|
static struct net_device_stats *get_stats(struct net_device *dev);
|
|
static int de600_start_xmit(struct sk_buff *skb, struct net_device *dev);
|
|
|
|
/* Dispatch from interrupts. */
|
|
static irqreturn_t de600_interrupt(int irq, void *dev_id, struct pt_regs *regs);
|
|
static int de600_tx_intr(struct net_device *dev, int irq_status);
|
|
static void de600_rx_intr(struct net_device *dev);
|
|
|
|
/* Initialization */
|
|
static void trigger_interrupt(struct net_device *dev);
|
|
static int adapter_init(struct net_device *dev);
|
|
|
|
/*
|
|
* Convenience macros/functions for D-Link adapter
|
|
*/
|
|
|
|
#define select_prn() outb_p(SELECT_PRN, COMMAND_PORT); DE600_SLOW_DOWN
|
|
#define select_nic() outb_p(SELECT_NIC, COMMAND_PORT); DE600_SLOW_DOWN
|
|
|
|
/* Thanks for hints from Mark Burton <markb@ordern.demon.co.uk> */
|
|
#define de600_put_byte(data) ( \
|
|
outb_p(((data) << 4) | WRITE_DATA , DATA_PORT), \
|
|
outb_p(((data) & 0xf0) | WRITE_DATA | HI_NIBBLE, DATA_PORT))
|
|
|
|
/*
|
|
* The first two outb_p()'s below could perhaps be deleted if there
|
|
* would be more delay in the last two. Not certain about it yet...
|
|
*/
|
|
#define de600_put_command(cmd) ( \
|
|
outb_p(( rx_page << 4) | COMMAND , DATA_PORT), \
|
|
outb_p(( rx_page & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT), \
|
|
outb_p(((rx_page | cmd) << 4) | COMMAND , DATA_PORT), \
|
|
outb_p(((rx_page | cmd) & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT))
|
|
|
|
#define de600_setup_address(addr,type) ( \
|
|
outb_p((((addr) << 4) & 0xf0) | type , DATA_PORT), \
|
|
outb_p(( (addr) & 0xf0) | type | HI_NIBBLE, DATA_PORT), \
|
|
outb_p((((addr) >> 4) & 0xf0) | type , DATA_PORT), \
|
|
outb_p((((addr) >> 8) & 0xf0) | type | HI_NIBBLE, DATA_PORT))
|
|
|
|
#define rx_page_adr() ((rx_page & RX_PAGE2_SELECT)?(MEM_6K):(MEM_4K))
|
|
|
|
/* Flip bit, only 2 pages */
|
|
#define next_rx_page() (rx_page ^= RX_PAGE2_SELECT)
|
|
|
|
#define tx_page_adr(a) (((a) + 1) * MEM_2K)
|