d2b21f1917
Add initial support for libertas devices using a GSPI interface. This has been tested with the 8686. GSPI is intended to be used on embedded systems. Board-specific parameters are required (see libertas_spi.h). Thanks to everyone who took a look at the earlier versions of the patch. Signed-off-by: Colin McCabe <colin@cozybit.com> Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
208 lines
8.9 KiB
C
208 lines
8.9 KiB
C
/*
|
|
* linux/drivers/net/wireless/libertas/if_spi.c
|
|
*
|
|
* Driver for Marvell SPI WLAN cards.
|
|
*
|
|
* Copyright 2008 Analog Devices Inc.
|
|
*
|
|
* Authors:
|
|
* Andrey Yurovsky <andrey@cozybit.com>
|
|
* Colin McCabe <colin@cozybit.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or (at
|
|
* your option) any later version.
|
|
*/
|
|
|
|
#ifndef _LBS_IF_SPI_H_
|
|
#define _LBS_IF_SPI_H_
|
|
|
|
#define IPFIELD_ALIGN_OFFSET 2
|
|
#define IF_SPI_CMD_BUF_SIZE 2400
|
|
|
|
/***************** Firmware *****************/
|
|
struct chip_ident {
|
|
u16 chip_id;
|
|
u16 name;
|
|
};
|
|
|
|
#define MAX_MAIN_FW_LOAD_CRC_ERR 10
|
|
|
|
/* Chunk size when loading the helper firmware */
|
|
#define HELPER_FW_LOAD_CHUNK_SZ 64
|
|
|
|
/* Value to write to indicate end of helper firmware dnld */
|
|
#define FIRMWARE_DNLD_OK 0x0000
|
|
|
|
/* Value to check once the main firmware is downloaded */
|
|
#define SUCCESSFUL_FW_DOWNLOAD_MAGIC 0x88888888
|
|
|
|
/***************** SPI Interface Unit *****************/
|
|
/* Masks used in SPI register read/write operations */
|
|
#define IF_SPI_READ_OPERATION_MASK 0x0
|
|
#define IF_SPI_WRITE_OPERATION_MASK 0x8000
|
|
|
|
/* SPI register offsets. 4-byte aligned. */
|
|
#define IF_SPI_DEVICEID_CTRL_REG 0x00 /* DeviceID controller reg */
|
|
#define IF_SPI_IO_READBASE_REG 0x04 /* Read I/O base reg */
|
|
#define IF_SPI_IO_WRITEBASE_REG 0x08 /* Write I/O base reg */
|
|
#define IF_SPI_IO_RDWRPORT_REG 0x0C /* Read/Write I/O port reg */
|
|
|
|
#define IF_SPI_CMD_READBASE_REG 0x10 /* Read command base reg */
|
|
#define IF_SPI_CMD_WRITEBASE_REG 0x14 /* Write command base reg */
|
|
#define IF_SPI_CMD_RDWRPORT_REG 0x18 /* Read/Write command port reg */
|
|
|
|
#define IF_SPI_DATA_READBASE_REG 0x1C /* Read data base reg */
|
|
#define IF_SPI_DATA_WRITEBASE_REG 0x20 /* Write data base reg */
|
|
#define IF_SPI_DATA_RDWRPORT_REG 0x24 /* Read/Write data port reg */
|
|
|
|
#define IF_SPI_SCRATCH_1_REG 0x28 /* Scratch reg 1 */
|
|
#define IF_SPI_SCRATCH_2_REG 0x2C /* Scratch reg 2 */
|
|
#define IF_SPI_SCRATCH_3_REG 0x30 /* Scratch reg 3 */
|
|
#define IF_SPI_SCRATCH_4_REG 0x34 /* Scratch reg 4 */
|
|
|
|
#define IF_SPI_TX_FRAME_SEQ_NUM_REG 0x38 /* Tx frame sequence number reg */
|
|
#define IF_SPI_TX_FRAME_STATUS_REG 0x3C /* Tx frame status reg */
|
|
|
|
#define IF_SPI_HOST_INT_CTRL_REG 0x40 /* Host interrupt controller reg */
|
|
|
|
#define IF_SPI_CARD_INT_CAUSE_REG 0x44 /* Card interrupt cause reg */
|
|
#define IF_SPI_CARD_INT_STATUS_REG 0x48 /* Card interupt status reg */
|
|
#define IF_SPI_CARD_INT_EVENT_MASK_REG 0x4C /* Card interrupt event mask */
|
|
#define IF_SPI_CARD_INT_STATUS_MASK_REG 0x50 /* Card interrupt status mask */
|
|
|
|
#define IF_SPI_CARD_INT_RESET_SELECT_REG 0x54 /* Card interrupt reset select */
|
|
|
|
#define IF_SPI_HOST_INT_CAUSE_REG 0x58 /* Host interrupt cause reg */
|
|
#define IF_SPI_HOST_INT_STATUS_REG 0x5C /* Host interrupt status reg */
|
|
#define IF_SPI_HOST_INT_EVENT_MASK_REG 0x60 /* Host interrupt event mask */
|
|
#define IF_SPI_HOST_INT_STATUS_MASK_REG 0x64 /* Host interrupt status mask */
|
|
#define IF_SPI_HOST_INT_RESET_SELECT_REG 0x68 /* Host interrupt reset select */
|
|
|
|
#define IF_SPI_DELAY_READ_REG 0x6C /* Delay read reg */
|
|
#define IF_SPI_SPU_BUS_MODE_REG 0x70 /* SPU BUS mode reg */
|
|
|
|
/***************** IF_SPI_DEVICEID_CTRL_REG *****************/
|
|
#define IF_SPI_DEVICEID_CTRL_REG_TO_CARD_ID(dc) ((dc & 0xffff0000)>>16)
|
|
#define IF_SPI_DEVICEID_CTRL_REG_TO_CARD_REV(dc) (dc & 0x000000ff)
|
|
|
|
/***************** IF_SPI_HOST_INT_CTRL_REG *****************/
|
|
/** Host Interrupt Control bit : Wake up */
|
|
#define IF_SPI_HICT_WAKE_UP (1<<0)
|
|
/** Host Interrupt Control bit : WLAN ready */
|
|
#define IF_SPI_HICT_WLAN_READY (1<<1)
|
|
/*#define IF_SPI_HICT_FIFO_FIRST_HALF_EMPTY (1<<2) */
|
|
/*#define IF_SPI_HICT_FIFO_SECOND_HALF_EMPTY (1<<3) */
|
|
/*#define IF_SPI_HICT_IRQSRC_WLAN (1<<4) */
|
|
/** Host Interrupt Control bit : Tx auto download */
|
|
#define IF_SPI_HICT_TX_DOWNLOAD_OVER_AUTO (1<<5)
|
|
/** Host Interrupt Control bit : Rx auto upload */
|
|
#define IF_SPI_HICT_RX_UPLOAD_OVER_AUTO (1<<6)
|
|
/** Host Interrupt Control bit : Command auto download */
|
|
#define IF_SPI_HICT_CMD_DOWNLOAD_OVER_AUTO (1<<7)
|
|
/** Host Interrupt Control bit : Command auto upload */
|
|
#define IF_SPI_HICT_CMD_UPLOAD_OVER_AUTO (1<<8)
|
|
|
|
/***************** IF_SPI_CARD_INT_CAUSE_REG *****************/
|
|
/** Card Interrupt Case bit : Tx download over */
|
|
#define IF_SPI_CIC_TX_DOWNLOAD_OVER (1<<0)
|
|
/** Card Interrupt Case bit : Rx upload over */
|
|
#define IF_SPI_CIC_RX_UPLOAD_OVER (1<<1)
|
|
/** Card Interrupt Case bit : Command download over */
|
|
#define IF_SPI_CIC_CMD_DOWNLOAD_OVER (1<<2)
|
|
/** Card Interrupt Case bit : Host event */
|
|
#define IF_SPI_CIC_HOST_EVENT (1<<3)
|
|
/** Card Interrupt Case bit : Command upload over */
|
|
#define IF_SPI_CIC_CMD_UPLOAD_OVER (1<<4)
|
|
/** Card Interrupt Case bit : Power down */
|
|
#define IF_SPI_CIC_POWER_DOWN (1<<5)
|
|
|
|
/***************** IF_SPI_CARD_INT_STATUS_REG *****************/
|
|
#define IF_SPI_CIS_TX_DOWNLOAD_OVER (1<<0)
|
|
#define IF_SPI_CIS_RX_UPLOAD_OVER (1<<1)
|
|
#define IF_SPI_CIS_CMD_DOWNLOAD_OVER (1<<2)
|
|
#define IF_SPI_CIS_HOST_EVENT (1<<3)
|
|
#define IF_SPI_CIS_CMD_UPLOAD_OVER (1<<4)
|
|
#define IF_SPI_CIS_POWER_DOWN (1<<5)
|
|
|
|
/***************** IF_SPI_HOST_INT_CAUSE_REG *****************/
|
|
#define IF_SPI_HICU_TX_DOWNLOAD_RDY (1<<0)
|
|
#define IF_SPI_HICU_RX_UPLOAD_RDY (1<<1)
|
|
#define IF_SPI_HICU_CMD_DOWNLOAD_RDY (1<<2)
|
|
#define IF_SPI_HICU_CARD_EVENT (1<<3)
|
|
#define IF_SPI_HICU_CMD_UPLOAD_RDY (1<<4)
|
|
#define IF_SPI_HICU_IO_WR_FIFO_OVERFLOW (1<<5)
|
|
#define IF_SPI_HICU_IO_RD_FIFO_UNDERFLOW (1<<6)
|
|
#define IF_SPI_HICU_DATA_WR_FIFO_OVERFLOW (1<<7)
|
|
#define IF_SPI_HICU_DATA_RD_FIFO_UNDERFLOW (1<<8)
|
|
#define IF_SPI_HICU_CMD_WR_FIFO_OVERFLOW (1<<9)
|
|
#define IF_SPI_HICU_CMD_RD_FIFO_UNDERFLOW (1<<10)
|
|
|
|
/***************** IF_SPI_HOST_INT_STATUS_REG *****************/
|
|
/** Host Interrupt Status bit : Tx download ready */
|
|
#define IF_SPI_HIST_TX_DOWNLOAD_RDY (1<<0)
|
|
/** Host Interrupt Status bit : Rx upload ready */
|
|
#define IF_SPI_HIST_RX_UPLOAD_RDY (1<<1)
|
|
/** Host Interrupt Status bit : Command download ready */
|
|
#define IF_SPI_HIST_CMD_DOWNLOAD_RDY (1<<2)
|
|
/** Host Interrupt Status bit : Card event */
|
|
#define IF_SPI_HIST_CARD_EVENT (1<<3)
|
|
/** Host Interrupt Status bit : Command upload ready */
|
|
#define IF_SPI_HIST_CMD_UPLOAD_RDY (1<<4)
|
|
/** Host Interrupt Status bit : I/O write FIFO overflow */
|
|
#define IF_SPI_HIST_IO_WR_FIFO_OVERFLOW (1<<5)
|
|
/** Host Interrupt Status bit : I/O read FIFO underflow */
|
|
#define IF_SPI_HIST_IO_RD_FIFO_UNDRFLOW (1<<6)
|
|
/** Host Interrupt Status bit : Data write FIFO overflow */
|
|
#define IF_SPI_HIST_DATA_WR_FIFO_OVERFLOW (1<<7)
|
|
/** Host Interrupt Status bit : Data read FIFO underflow */
|
|
#define IF_SPI_HIST_DATA_RD_FIFO_UNDERFLOW (1<<8)
|
|
/** Host Interrupt Status bit : Command write FIFO overflow */
|
|
#define IF_SPI_HIST_CMD_WR_FIFO_OVERFLOW (1<<9)
|
|
/** Host Interrupt Status bit : Command read FIFO underflow */
|
|
#define IF_SPI_HIST_CMD_RD_FIFO_UNDERFLOW (1<<10)
|
|
|
|
/***************** IF_SPI_HOST_INT_STATUS_MASK_REG *****************/
|
|
/** Host Interrupt Status Mask bit : Tx download ready */
|
|
#define IF_SPI_HISM_TX_DOWNLOAD_RDY (1<<0)
|
|
/** Host Interrupt Status Mask bit : Rx upload ready */
|
|
#define IF_SPI_HISM_RX_UPLOAD_RDY (1<<1)
|
|
/** Host Interrupt Status Mask bit : Command download ready */
|
|
#define IF_SPI_HISM_CMD_DOWNLOAD_RDY (1<<2)
|
|
/** Host Interrupt Status Mask bit : Card event */
|
|
#define IF_SPI_HISM_CARDEVENT (1<<3)
|
|
/** Host Interrupt Status Mask bit : Command upload ready */
|
|
#define IF_SPI_HISM_CMD_UPLOAD_RDY (1<<4)
|
|
/** Host Interrupt Status Mask bit : I/O write FIFO overflow */
|
|
#define IF_SPI_HISM_IO_WR_FIFO_OVERFLOW (1<<5)
|
|
/** Host Interrupt Status Mask bit : I/O read FIFO underflow */
|
|
#define IF_SPI_HISM_IO_RD_FIFO_UNDERFLOW (1<<6)
|
|
/** Host Interrupt Status Mask bit : Data write FIFO overflow */
|
|
#define IF_SPI_HISM_DATA_WR_FIFO_OVERFLOW (1<<7)
|
|
/** Host Interrupt Status Mask bit : Data write FIFO underflow */
|
|
#define IF_SPI_HISM_DATA_RD_FIFO_UNDERFLOW (1<<8)
|
|
/** Host Interrupt Status Mask bit : Command write FIFO overflow */
|
|
#define IF_SPI_HISM_CMD_WR_FIFO_OVERFLOW (1<<9)
|
|
/** Host Interrupt Status Mask bit : Command write FIFO underflow */
|
|
#define IF_SPI_HISM_CMD_RD_FIFO_UNDERFLOW (1<<10)
|
|
|
|
/***************** IF_SPI_SPU_BUS_MODE_REG *****************/
|
|
/* SCK edge on which the WLAN module outputs data on MISO */
|
|
#define IF_SPI_BUS_MODE_SPI_CLOCK_PHASE_FALLING 0x8
|
|
#define IF_SPI_BUS_MODE_SPI_CLOCK_PHASE_RISING 0x0
|
|
|
|
/* In a SPU read operation, there is a delay between writing the SPU
|
|
* register name and getting back data from the WLAN module.
|
|
* This can be specified in terms of nanoseconds or in terms of dummy
|
|
* clock cycles which the master must output before receiving a response. */
|
|
#define IF_SPI_BUS_MODE_DELAY_METHOD_DUMMY_CLOCK 0x4
|
|
#define IF_SPI_BUS_MODE_DELAY_METHOD_TIMED 0x0
|
|
|
|
/* Some different modes of SPI operation */
|
|
#define IF_SPI_BUS_MODE_8_BIT_ADDRESS_16_BIT_DATA 0x00
|
|
#define IF_SPI_BUS_MODE_8_BIT_ADDRESS_32_BIT_DATA 0x01
|
|
#define IF_SPI_BUS_MODE_16_BIT_ADDRESS_16_BIT_DATA 0x02
|
|
#define IF_SPI_BUS_MODE_16_BIT_ADDRESS_32_BIT_DATA 0x03
|
|
|
|
#endif
|