dd091c7b32
With CONFIG_USB_ULPI=y, CONFIG_USB<=m, CONFIG_PCI=n and CONFIG_USB_OTG_UTILS=n, which is the default used for mx31moboard, the build for all mx3 platforms fails because drivers/usb/otg/ulpi.c where otg_ulpi_create is defined is not compiled. Build error: arch/arm/mach-mx3/built-in.o: In function `mxc_board_init': kzmarm11.c:(.init.text+0x73c): undefined reference to `otg_ulpi_create' kzmarm11.c:(.init.text+0x1020): undefined reference to `otg_ulpi_create' This isn't a strong dependency as drivers/usb/otg/ulpi.c doesn't use functions defined in drivers/usb/otg/otg.o and is only needed to get ulpi.o linked into the kernel image. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
72 lines
2.1 KiB
Text
72 lines
2.1 KiB
Text
#
|
|
# USB OTG infrastructure may be needed for peripheral-only, host-only,
|
|
# or OTG-capable configurations when OTG transceivers or controllers
|
|
# are used.
|
|
#
|
|
|
|
comment "OTG and related infrastructure"
|
|
|
|
config USB_OTG_UTILS
|
|
bool
|
|
help
|
|
Select this to make sure the build includes objects from
|
|
the OTG infrastructure directory.
|
|
|
|
if USB || USB_GADGET
|
|
|
|
#
|
|
# USB Transceiver Drivers
|
|
#
|
|
config USB_GPIO_VBUS
|
|
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
|
|
depends on GENERIC_GPIO
|
|
select USB_OTG_UTILS
|
|
help
|
|
Provides simple GPIO VBUS sensing for controllers with an
|
|
internal transceiver via the otg_transceiver interface, and
|
|
optionally control of a D+ pullup GPIO as well as a VBUS
|
|
current limit regulator.
|
|
|
|
config ISP1301_OMAP
|
|
tristate "Philips ISP1301 with OMAP OTG"
|
|
depends on I2C && ARCH_OMAP_OTG
|
|
select USB_OTG_UTILS
|
|
help
|
|
If you say yes here you get support for the Philips ISP1301
|
|
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
|
The ISP1301 is a full speed USB transceiver which is used in
|
|
products including H2, H3, and H4 development boards for Texas
|
|
Instruments OMAP processors.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called isp1301_omap.
|
|
|
|
config USB_ULPI
|
|
bool "Generic ULPI Transceiver Driver"
|
|
depends on ARM
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support ULPI connected USB OTG transceivers which
|
|
are likely found on embedded boards.
|
|
|
|
The only chip currently supported is NXP's ISP1504
|
|
|
|
config TWL4030_USB
|
|
tristate "TWL4030 USB Transceiver Driver"
|
|
depends on TWL4030_CORE && REGULATOR_TWL4030
|
|
select USB_OTG_UTILS
|
|
help
|
|
Enable this to support the USB OTG transceiver on TWL4030
|
|
family chips (including the TWL5030 and TPS659x0 devices).
|
|
This transceiver supports high and full speed devices plus,
|
|
in host mode, low speed.
|
|
|
|
config NOP_USB_XCEIV
|
|
tristate "NOP USB Transceiver Driver"
|
|
select USB_OTG_UTILS
|
|
help
|
|
this driver is to be used by all the usb transceiver which are either
|
|
built-in with usb ip or which are autonomous and doesn't require any
|
|
phy programming such as ISP1x04 etc.
|
|
|
|
endif # USB || OTG
|