kernel-fxtec-pro1x/arch/cris/arch-v32/Kconfig

if ETRAX_ARCH_V32

source arch/cris/arch-v32/mach-fs/Kconfig
source arch/cris/arch-v32/mach-a3/Kconfig

source drivers/cpufreq/Kconfig

config ETRAX_DRAM_VIRTUAL_BASE
	hex
	depends on ETRAX_ARCH_V32
	default "c0000000"

choice
	prompt "Nbr of Ethernet LED groups"
	depends on ETRAX_ARCH_V32
	default ETRAX_NBR_LED_GRP_ONE
	help
	  Select how many Ethernet LED groups that can be used. Usually one per Ethernet
	  interface is a good choice.

config	ETRAX_NBR_LED_GRP_ZERO
	bool "Use zero LED groups"
	help
	  Select this if you do not want any Ethernet LEDs.

config	ETRAX_NBR_LED_GRP_ONE
	bool "Use one LED group"
	help
	  Select this if you want one Ethernet LED group. This LED group
	  can be used for one or more Ethernet interfaces. However, it is
	  recommended that each Ethernet interface use a dedicated LED group.

config	ETRAX_NBR_LED_GRP_TWO
	bool "Use two LED groups"
	help
	  Select this if you want two Ethernet LED groups. This is the
	  best choice if you have more than one Ethernet interface and
	  would like to have separate LEDs for the interfaces.

endchoice

config ETRAX_LED_G_NET0
	string "Ethernet LED group 0 green LED bit"
	depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
	default "PA3"
	help
	  Bit to use for the green LED in Ethernet LED group 0.

config ETRAX_LED_R_NET0
	string "Ethernet LED group 0 red LED bit"
	depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
	default "PA4"
	help
	  Bit to use for the red LED in Ethernet LED group 0.

config ETRAX_LED_G_NET1
	string "Ethernet group 1 green LED bit"
	depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
	default ""
	help
	  Bit to use for the green LED in Ethernet LED group 1.

config ETRAX_LED_R_NET1
	string "Ethernet group 1 red LED bit"
	depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
	default ""
	help
	  Bit to use for the red LED in Ethernet LED group 1.

config ETRAX_V32_LED2G
	string "Second green LED bit"
	depends on ETRAX_ARCH_V32
	default "PA5"
	help
	  Bit to use for the first green LED (status LED).
	  Most Axis products use bit A5 here.

config ETRAX_V32_LED2R
	string "Second red LED bit"
	depends on ETRAX_ARCH_V32
	default "PA6"
	help
	  Bit to use for the first red LED (network LED).
	  Most Axis products use bit A6 here.

config ETRAX_V32_LED3G
	string "Third green LED bit"
	depends on ETRAX_ARCH_V32
	default "PA7"
	help
	  Bit to use for the first green LED (drive/power LED).
	  Most Axis products use bit A7 here.

config ETRAX_V32_LED3R
	string "Third red LED bit"
	depends on ETRAX_ARCH_V32
	default "PA7"
	help
	  Bit to use for the first red LED (drive/power LED).
	  Most Axis products use bit A7 here.

choice
	prompt "Kernel GDB port"
	depends on ETRAX_KGDB
	default ETRAX_KGDB_PORT0
	help
	  Choose a serial port for kernel debugging.  NOTE: This port should
	  not be enabled under Drivers for built-in interfaces (as it has its
	  own initialization code) and should not be the same as the debug port.

config ETRAX_KGDB_PORT4
	bool "Serial-4"
	depends on ETRAX_SERIAL_PORTS = 5
	help
	  Use serial port 4 for kernel debugging.

endchoice

config ETRAX_MEM_GRP1_CONFIG
	hex "MEM_GRP1_CONFIG"
	depends on ETRAX_ARCH_V32
	default "4044a"
	help
	  Waitstates for flash. The default value is suitable for the
	  standard flashes used in axis products (120 ns).

config ETRAX_MEM_GRP2_CONFIG
	hex "MEM_GRP2_CONFIG"
	depends on ETRAX_ARCH_V32
	default "0"
	help
	  Waitstates for SRAM. 0 is a good choice for most Axis products.

config ETRAX_MEM_GRP3_CONFIG
	hex "MEM_GRP3_CONFIG"
	depends on ETRAX_ARCH_V32
	default "0"
	help
	  Waitstates for CSP0-3. 0 is a good choice for most Axis products.
	  It may need to be changed if external devices such as extra
	  register-mapped LEDs are used.

config ETRAX_MEM_GRP4_CONFIG
	hex "MEM_GRP4_CONFIG"
	depends on ETRAX_ARCH_V32
	default "0"
	help
	  Waitstates for CSP4-6. 0 is a good choice for most Axis products.

config ETRAX_SDRAM_GRP0_CONFIG
	hex "SDRAM_GRP0_CONFIG"
	depends on ETRAX_ARCH_V32
	default "336"
	help
	  SDRAM configuration for group 0. The value depends on the
	  hardware configuration. The default value is suitable
	  for 32 MB organized as two 16 bits chips (e.g. Axis
	  part number 18550) connected as one 32 bit device (i.e. in
	  the same group).

config ETRAX_SDRAM_GRP1_CONFIG
	hex "SDRAM_GRP1_CONFIG"
	depends on ETRAX_ARCH_V32
	default "0"
	help
	  SDRAM configuration for group 1. The default value is 0
	  because group 1 is not used in the default configuration,
	  described in the help for SDRAM_GRP0_CONFIG.

config ETRAX_SDRAM_TIMING
	hex "SDRAM_TIMING"
	depends on ETRAX_ARCH_V32
	default "104a"
	help
	  SDRAM timing parameters. The default value is ok for
	  most hardwares but large SDRAMs may require a faster
	  refresh (a.k.a 8K refresh). The default value implies
	  100MHz clock and SDR mode.

config ETRAX_SDRAM_COMMAND
	hex "SDRAM_COMMAND"
	depends on ETRAX_ARCH_V32
	default "0"
	help
	  SDRAM command. Should be 0 unless you really know what
	  you are doing (may be != 0 for unusual address line
	  mappings such as in a MCM)..

config ETRAX_DEF_GIO_PA_OE
	hex "GIO_PA_OE"
	depends on ETRAX_ARCH_V32
	default "1c"
	help
	  Configures the direction of general port A bits.  1 is out, 0 is in.
	  This is often totally different depending on the product used.
	  There are some guidelines though - if you know that only LED's are
	  connected to port PA, then they are usually connected to bits 2-4
	  and you can therefore use 1c.  On other boards which don't have the
	  LED's at the general ports, these bits are used for all kinds of
	  stuff.  If you don't know what to use, it is always safe to put all
	  as inputs, although floating inputs isn't good.

config ETRAX_DEF_GIO_PA_OUT
	hex "GIO_PA_OUT"
	depends on ETRAX_ARCH_V32
	default "00"
	help
	  Configures the initial data for the general port A bits.  Most
	  products should use 00 here.

config ETRAX_DEF_GIO_PB_OE
	hex "GIO_PB_OE"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the direction of general port B bits.  1 is out, 0 is in.
	  This is often totally different depending on the product used.
	  There are some guidelines though - if you know that only LED's are
	  connected to port PA, then they are usually connected to bits 2-4
	  and you can therefore use 1c.  On other boards which don't have the
	  LED's at the general ports, these bits are used for all kinds of
	  stuff.  If you don't know what to use, it is always safe to put all
	  as inputs, although floating inputs isn't good.

config ETRAX_DEF_GIO_PB_OUT
	hex "GIO_PB_OUT"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the initial data for the general port B bits.  Most
	  products should use 00000 here.

config ETRAX_DEF_GIO_PC_OE
	hex "GIO_PC_OE"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the direction of general port C bits.  1 is out, 0 is in.
	  This is often totally different depending on the product used.
	  There are some guidelines though - if you know that only LED's are
	  connected to port PA, then they are usually connected to bits 2-4
	  and you can therefore use 1c.  On other boards which don't have the
	  LED's at the general ports, these bits are used for all kinds of
	  stuff.  If you don't know what to use, it is always safe to put all
	  as inputs, although floating inputs isn't good.

config ETRAX_DEF_GIO_PC_OUT
	hex "GIO_PC_OUT"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the initial data for the general port C bits.  Most
	  products should use 00000 here.

config ETRAX_DEF_GIO_PD_OE
	hex "GIO_PD_OE"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the direction of general port D bits.  1 is out, 0 is in.
	  This is often totally different depending on the product used.
	  There are some guidelines though - if you know that only LED's are
	  connected to port PA, then they are usually connected to bits 2-4
	  and you can therefore use 1c.  On other boards which don't have the
	  LED's at the general ports, these bits are used for all kinds of
	  stuff.  If you don't know what to use, it is always safe to put all
	  as inputs, although floating inputs isn't good.

config ETRAX_DEF_GIO_PD_OUT
	hex "GIO_PD_OUT"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the initial data for the general port D bits.  Most
	  products should use 00000 here.

config ETRAX_DEF_GIO_PE_OE
	hex "GIO_PE_OE"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the direction of general port E bits.  1 is out, 0 is in.
	  This is often totally different depending on the product used.
	  There are some guidelines though - if you know that only LED's are
	  connected to port PA, then they are usually connected to bits 2-4
	  and you can therefore use 1c.  On other boards which don't have the
	  LED's at the general ports, these bits are used for all kinds of
	  stuff.  If you don't know what to use, it is always safe to put all
	  as inputs, although floating inputs isn't good.

config ETRAX_DEF_GIO_PE_OUT
	hex "GIO_PE_OUT"
	depends on ETRAX_ARCH_V32
	default "00000"
	help
	  Configures the initial data for the general port E bits.  Most
	  products should use 00000 here.

endif