1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
450 lines
15 KiB
Text
450 lines
15 KiB
Text
Documentation/networking/vortex.txt
|
|
Andrew Morton <andrewm@uow.edu.au>
|
|
30 April 2000
|
|
|
|
|
|
This document describes the usage and errata of the 3Com "Vortex" device
|
|
driver for Linux, 3c59x.c.
|
|
|
|
The driver was written by Donald Becker <becker@scyld.com>
|
|
|
|
Don is no longer the prime maintainer of this version of the driver.
|
|
Please report problems to one or more of:
|
|
|
|
Andrew Morton <andrewm@uow.edu.au>
|
|
Netdev mailing list <netdev@oss.sgi.com>
|
|
Linux kernel mailing list <linux-kernel@vger.kernel.org>
|
|
|
|
Please note the 'Reporting and Diagnosing Problems' section at the end
|
|
of this file.
|
|
|
|
|
|
Since kernel 2.3.99-pre6, this driver incorporates the support for the
|
|
3c575-series Cardbus cards which used to be handled by 3c575_cb.c.
|
|
|
|
This driver supports the following hardware:
|
|
|
|
3c590 Vortex 10Mbps
|
|
3c592 EISA 10mbps Demon/Vortex
|
|
3c597 EISA Fast Demon/Vortex
|
|
3c595 Vortex 100baseTx
|
|
3c595 Vortex 100baseT4
|
|
3c595 Vortex 100base-MII
|
|
3Com Vortex
|
|
3c900 Boomerang 10baseT
|
|
3c900 Boomerang 10Mbps Combo
|
|
3c900 Cyclone 10Mbps TPO
|
|
3c900B Cyclone 10Mbps T
|
|
3c900 Cyclone 10Mbps Combo
|
|
3c900 Cyclone 10Mbps TPC
|
|
3c900B-FL Cyclone 10base-FL
|
|
3c905 Boomerang 100baseTx
|
|
3c905 Boomerang 100baseT4
|
|
3c905B Cyclone 100baseTx
|
|
3c905B Cyclone 10/100/BNC
|
|
3c905B-FX Cyclone 100baseFx
|
|
3c905C Tornado
|
|
3c980 Cyclone
|
|
3cSOHO100-TX Hurricane
|
|
3c555 Laptop Hurricane
|
|
3c575 Boomerang CardBus
|
|
3CCFE575 Cyclone CardBus
|
|
3CCFE575CT Cyclone CardBus
|
|
3CCFE656 Cyclone CardBus
|
|
3CCFEM656 Cyclone CardBus
|
|
3c450 Cyclone/unknown
|
|
|
|
|
|
Module parameters
|
|
=================
|
|
|
|
There are several parameters which may be provided to the driver when
|
|
its module is loaded. These are usually placed in /etc/modprobe.conf
|
|
(/etc/modules.conf in 2.4). Example:
|
|
|
|
options 3c59x debug=3 rx_copybreak=300
|
|
|
|
If you are using the PCMCIA tools (cardmgr) then the options may be
|
|
placed in /etc/pcmcia/config.opts:
|
|
|
|
module "3c59x" opts "debug=3 rx_copybreak=300"
|
|
|
|
|
|
The supported parameters are:
|
|
|
|
debug=N
|
|
|
|
Where N is a number from 0 to 7. Anything above 3 produces a lot
|
|
of output in your system logs. debug=1 is default.
|
|
|
|
options=N1,N2,N3,...
|
|
|
|
Each number in the list provides an option to the corresponding
|
|
network card. So if you have two 3c905's and you wish to provide
|
|
them with option 0x204 you would use:
|
|
|
|
options=0x204,0x204
|
|
|
|
The individual options are composed of a number of bitfields which
|
|
have the following meanings:
|
|
|
|
Possible media type settings
|
|
0 10baseT
|
|
1 10Mbs AUI
|
|
2 undefined
|
|
3 10base2 (BNC)
|
|
4 100base-TX
|
|
5 100base-FX
|
|
6 MII (Media Independent Interface)
|
|
7 Use default setting from EEPROM
|
|
8 Autonegotiate
|
|
9 External MII
|
|
10 Use default setting from EEPROM
|
|
|
|
When generating a value for the 'options' setting, the above media
|
|
selection values may be OR'ed (or added to) the following:
|
|
|
|
0x8000 Set driver debugging level to 7
|
|
0x4000 Set driver debugging level to 2
|
|
0x0400 Enable Wake-on-LAN
|
|
0x0200 Force full duplex mode.
|
|
0x0010 Bus-master enable bit (Old Vortex cards only)
|
|
|
|
For example:
|
|
|
|
insmod 3c59x options=0x204
|
|
|
|
will force full-duplex 100base-TX, rather than allowing the usual
|
|
autonegotiation.
|
|
|
|
global_options=N
|
|
|
|
Sets the `options' parameter for all 3c59x NICs in the machine.
|
|
Entries in the `options' array above will override any setting of
|
|
this.
|
|
|
|
full_duplex=N1,N2,N3...
|
|
|
|
Similar to bit 9 of 'options'. Forces the corresponding card into
|
|
full-duplex mode. Please use this in preference to the `options'
|
|
parameter.
|
|
|
|
In fact, please don't use this at all! You're better off getting
|
|
autonegotiation working properly.
|
|
|
|
global_full_duplex=N1
|
|
|
|
Sets full duplex mode for all 3c59x NICs in the machine. Entries
|
|
in the `full_duplex' array above will override any setting of this.
|
|
|
|
flow_ctrl=N1,N2,N3...
|
|
|
|
Use 802.3x MAC-layer flow control. The 3com cards only support the
|
|
PAUSE command, which means that they will stop sending packets for a
|
|
short period if they receive a PAUSE frame from the link partner.
|
|
|
|
The driver only allows flow control on a link which is operating in
|
|
full duplex mode.
|
|
|
|
This feature does not appear to work on the 3c905 - only 3c905B and
|
|
3c905C have been tested.
|
|
|
|
The 3com cards appear to only respond to PAUSE frames which are
|
|
sent to the reserved destination address of 01:80:c2:00:00:01. They
|
|
do not honour PAUSE frames which are sent to the station MAC address.
|
|
|
|
rx_copybreak=M
|
|
|
|
The driver preallocates 32 full-sized (1536 byte) network buffers
|
|
for receiving. When a packet arrives, the driver has to decide
|
|
whether to leave the packet in its full-sized buffer, or to allocate
|
|
a smaller buffer and copy the packet across into it.
|
|
|
|
This is a speed/space tradeoff.
|
|
|
|
The value of rx_copybreak is used to decide when to make the copy.
|
|
If the packet size is less than rx_copybreak, the packet is copied.
|
|
The default value for rx_copybreak is 200 bytes.
|
|
|
|
max_interrupt_work=N
|
|
|
|
The driver's interrupt service routine can handle many receive and
|
|
transmit packets in a single invocation. It does this in a loop.
|
|
The value of max_interrupt_work governs how mnay times the interrupt
|
|
service routine will loop. The default value is 32 loops. If this
|
|
is exceeded the interrupt service routine gives up and generates a
|
|
warning message "eth0: Too much work in interrupt".
|
|
|
|
hw_checksums=N1,N2,N3,...
|
|
|
|
Recent 3com NICs are able to generate IPv4, TCP and UDP checksums
|
|
in hardware. Linux has used the Rx checksumming for a long time.
|
|
The "zero copy" patch which is planned for the 2.4 kernel series
|
|
allows you to make use of the NIC's DMA scatter/gather and transmit
|
|
checksumming as well.
|
|
|
|
The driver is set up so that, when the zerocopy patch is applied,
|
|
all Tornado and Cyclone devices will use S/G and Tx checksums.
|
|
|
|
This module parameter has been provided so you can override this
|
|
decision. If you think that Tx checksums are causing a problem, you
|
|
may disable the feature with `hw_checksums=0'.
|
|
|
|
If you think your NIC should be performing Tx checksumming and the
|
|
driver isn't enabling it, you can force the use of hardware Tx
|
|
checksumming with `hw_checksums=1'.
|
|
|
|
The driver drops a message in the logfiles to indicate whether or
|
|
not it is using hardware scatter/gather and hardware Tx checksums.
|
|
|
|
Scatter/gather and hardware checksums provide considerable
|
|
performance improvement for the sendfile() system call, but a small
|
|
decrease in throughput for send(). There is no effect upon receive
|
|
efficiency.
|
|
|
|
compaq_ioaddr=N
|
|
compaq_irq=N
|
|
compaq_device_id=N
|
|
|
|
"Variables to work-around the Compaq PCI BIOS32 problem"....
|
|
|
|
watchdog=N
|
|
|
|
Sets the time duration (in milliseconds) after which the kernel
|
|
decides that the transmitter has become stuck and needs to be reset.
|
|
This is mainly for debugging purposes, although it may be advantageous
|
|
to increase this value on LANs which have very high collision rates.
|
|
The default value is 5000 (5.0 seconds).
|
|
|
|
enable_wol=N1,N2,N3,...
|
|
|
|
Enable Wake-on-LAN support for the relevant interface. Donald
|
|
Becker's `ether-wake' application may be used to wake suspended
|
|
machines.
|
|
|
|
Also enables the NIC's power management support.
|
|
|
|
global_enable_wol=N
|
|
|
|
Sets enable_wol mode for all 3c59x NICs in the machine. Entries in
|
|
the `enable_wol' array above will override any setting of this.
|
|
|
|
Media selection
|
|
---------------
|
|
|
|
A number of the older NICs such as the 3c590 and 3c900 series have
|
|
10base2 and AUI interfaces.
|
|
|
|
Prior to January, 2001 this driver would autoeselect the 10base2 or AUI
|
|
port if it didn't detect activity on the 10baseT port. It would then
|
|
get stuck on the 10base2 port and a driver reload was necessary to
|
|
switch back to 10baseT. This behaviour could not be prevented with a
|
|
module option override.
|
|
|
|
Later (current) versions of the driver _do_ support locking of the
|
|
media type. So if you load the driver module with
|
|
|
|
modprobe 3c59x options=0
|
|
|
|
it will permanently select the 10baseT port. Automatic selection of
|
|
other media types does not occur.
|
|
|
|
|
|
Transmit error, Tx status register 82
|
|
-------------------------------------
|
|
|
|
This is a common error which is almost always caused by another host on
|
|
the same network being in full-duplex mode, while this host is in
|
|
half-duplex mode. You need to find that other host and make it run in
|
|
half-duplex mode or fix this host to run in full-duplex mode.
|
|
|
|
As a last resort, you can force the 3c59x driver into full-duplex mode
|
|
with
|
|
|
|
options 3c59x full_duplex=1
|
|
|
|
but this has to be viewed as a workaround for broken network gear and
|
|
should only really be used for equipment which cannot autonegotiate.
|
|
|
|
|
|
Additional resources
|
|
--------------------
|
|
|
|
Details of the device driver implementation are at the top of the source file.
|
|
|
|
Additional documentation is available at Don Becker's Linux Drivers site:
|
|
|
|
http://www.scyld.com/network/vortex.html
|
|
|
|
Donald Becker's driver development site:
|
|
|
|
http://www.scyld.com/network
|
|
|
|
Donald's vortex-diag program is useful for inspecting the NIC's state:
|
|
|
|
http://www.scyld.com/diag/#pci-diags
|
|
|
|
Donald's mii-diag program may be used for inspecting and manipulating
|
|
the NIC's Media Independent Interface subsystem:
|
|
|
|
http://www.scyld.com/diag/#mii-diag
|
|
|
|
Donald's wake-on-LAN page:
|
|
|
|
http://www.scyld.com/expert/wake-on-lan.html
|
|
|
|
3Com's documentation for many NICs, including the ones supported by
|
|
this driver is available at
|
|
|
|
http://support.3com.com/partners/developer/developer_form.html
|
|
|
|
3Com's DOS-based application for setting up the NICs EEPROMs:
|
|
|
|
ftp://ftp.3com.com/pub/nic/3c90x/3c90xx2.exe
|
|
|
|
Driver updates and a detailed changelog for the modifications which
|
|
were made for the 2.3/2,4 series kernel is available at
|
|
|
|
http://www.uow.edu.au/~andrewm/linux/#3c59x-2.3
|
|
|
|
|
|
Autonegotiation notes
|
|
---------------------
|
|
|
|
The driver uses a one-minute heartbeat for adapting to changes in
|
|
the external LAN environment. This means that when, for example, a
|
|
machine is unplugged from a hubbed 10baseT LAN plugged into a
|
|
switched 100baseT LAN, the throughput will be quite dreadful for up
|
|
to sixty seconds. Be patient.
|
|
|
|
Cisco interoperability note from Walter Wong <wcw+@CMU.EDU>:
|
|
|
|
On a side note, adding HAS_NWAY seems to share a problem with the
|
|
Cisco 6509 switch. Specifically, you need to change the spanning
|
|
tree parameter for the port the machine is plugged into to 'portfast'
|
|
mode. Otherwise, the negotiation fails. This has been an issue
|
|
we've noticed for a while but haven't had the time to track down.
|
|
|
|
Cisco switches (Jeff Busch <jbusch@deja.com>)
|
|
|
|
My "standard config" for ports to which PC's/servers connect directly:
|
|
|
|
interface FastEthernet0/N
|
|
description machinename
|
|
load-interval 30
|
|
spanning-tree portfast
|
|
|
|
If autonegotiation is a problem, you may need to specify "speed
|
|
100" and "duplex full" as well (or "speed 10" and "duplex half").
|
|
|
|
WARNING: DO NOT hook up hubs/switches/bridges to these
|
|
specially-configured ports! The switch will become very confused.
|
|
|
|
|
|
Reporting and diagnosing problems
|
|
---------------------------------
|
|
|
|
Maintainers find that accurate and complete problem reports are
|
|
invaluable in resolving driver problems. We are frequently not able to
|
|
reproduce problems and must rely on your patience and efforts to get to
|
|
the bottom of the problem.
|
|
|
|
If you believe you have a driver problem here are some of the
|
|
steps you should take:
|
|
|
|
- Is it really a driver problem?
|
|
|
|
Eliminate some variables: try different cards, different
|
|
computers, different cables, different ports on the switch/hub,
|
|
different versions of the kernel or ofthe driver, etc.
|
|
|
|
- OK, it's a driver problem.
|
|
|
|
You need to generate a report. Typically this is an email to the
|
|
maintainer and/or linux-net@vger.kernel.org. The maintainer's
|
|
email address will be inthe driver source or in the MAINTAINERS file.
|
|
|
|
- The contents of your report will vary a lot depending upon the
|
|
problem. If it's a kernel crash then you should refer to the
|
|
REPORTING-BUGS file.
|
|
|
|
But for most problems it is useful to provide the following:
|
|
|
|
o Kernel version, driver version
|
|
|
|
o A copy of the banner message which the driver generates when
|
|
it is initialised. For example:
|
|
|
|
eth0: 3Com PCI 3c905C Tornado at 0xa400, 00:50:da:6a:88:f0, IRQ 19
|
|
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
|
|
MII transceiver found at address 24, status 782d.
|
|
Enabling bus-master transmits and whole-frame receives.
|
|
|
|
NOTE: You must provide the `debug=2' modprobe option to generate
|
|
a full detection message. Please do this:
|
|
|
|
modprobe 3c59x debug=2
|
|
|
|
o If it is a PCI device, the relevant output from 'lspci -vx', eg:
|
|
|
|
00:09.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 74)
|
|
Subsystem: 3Com Corporation: Unknown device 9200
|
|
Flags: bus master, medium devsel, latency 32, IRQ 19
|
|
I/O ports at a400 [size=128]
|
|
Memory at db000000 (32-bit, non-prefetchable) [size=128]
|
|
Expansion ROM at <unassigned> [disabled] [size=128K]
|
|
Capabilities: [dc] Power Management version 2
|
|
00: b7 10 00 92 07 00 10 02 74 00 00 02 08 20 00 00
|
|
10: 01 a4 00 00 00 00 00 db 00 00 00 00 00 00 00 00
|
|
20: 00 00 00 00 00 00 00 00 00 00 00 00 b7 10 00 10
|
|
30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 0a 0a
|
|
|
|
o A description of the environment: 10baseT? 100baseT?
|
|
full/half duplex? switched or hubbed?
|
|
|
|
o Any additional module parameters which you may be providing to the driver.
|
|
|
|
o Any kernel logs which are produced. The more the merrier.
|
|
If this is a large file and you are sending your report to a
|
|
mailing list, mention that you have the logfile, but don't send
|
|
it. If you're reporting direct to the maintainer then just send
|
|
it.
|
|
|
|
To ensure that all kernel logs are available, add the
|
|
following line to /etc/syslog.conf:
|
|
|
|
kern.* /var/log/messages
|
|
|
|
Then restart syslogd with:
|
|
|
|
/etc/rc.d/init.d/syslog restart
|
|
|
|
(The above may vary, depending upon which Linux distribution you use).
|
|
|
|
o If your problem is reproducible then that's great. Try the
|
|
following:
|
|
|
|
1) Increase the debug level. Usually this is done via:
|
|
|
|
a) modprobe driver debug=7
|
|
b) In /etc/modprobe.conf (or /etc/modules.conf for 2.4):
|
|
options driver debug=7
|
|
|
|
2) Recreate the problem with the higher debug level,
|
|
send all logs to the maintainer.
|
|
|
|
3) Download you card's diagnostic tool from Donald
|
|
Backer's website http://www.scyld.com/diag. Download
|
|
mii-diag.c as well. Build these.
|
|
|
|
a) Run 'vortex-diag -aaee' and 'mii-diag -v' when the card is
|
|
working correctly. Save the output.
|
|
|
|
b) Run the above commands when the card is malfunctioning. Send
|
|
both sets of output.
|
|
|
|
Finally, please be patient and be prepared to do some work. You may end up working on
|
|
this problem for a week or more as the maintainer asks more questions, asks for more
|
|
tests, asks for patches to be applied, etc. At the end of it all, the problem may even
|
|
remain unresolved.
|
|
|