faa246debf
Add the compatible string for Meson8b in Meson pinctrl documentation and add new information for Meson8b in source code comments. Signed-off-by: Carlo Caione <carlo@endlessm.com> Acked-by: Beniamino Galvani <b.galvani@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
96 lines
2.7 KiB
Text
96 lines
2.7 KiB
Text
== Amlogic Meson pinmux controller ==
|
|
|
|
Required properties for the root node:
|
|
- compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl"
|
|
- reg: address and size of registers controlling irq functionality
|
|
|
|
=== GPIO sub-nodes ===
|
|
|
|
The 2 power domains of the controller (regular and always-on) are
|
|
represented as sub-nodes and each of them acts as a GPIO controller.
|
|
|
|
Required properties for sub-nodes are:
|
|
- reg: should contain address and size for mux, pull-enable, pull and
|
|
gpio register sets
|
|
- reg-names: an array of strings describing the "reg" entries. Must
|
|
contain "mux", "pull" and "gpio". "pull-enable" is optional and
|
|
when it is missing the "pull" registers are used instead
|
|
- gpio-controller: identifies the node as a gpio controller
|
|
- #gpio-cells: must be 2
|
|
|
|
Valid sub-node names are:
|
|
- "banks" for the regular domain
|
|
- "ao-bank" for the always-on domain
|
|
|
|
=== Other sub-nodes ===
|
|
|
|
Child nodes without the "gpio-controller" represent some desired
|
|
configuration for a pin or a group. Those nodes can be pinmux nodes or
|
|
configuration nodes.
|
|
|
|
Required properties for pinmux nodes are:
|
|
- groups: a list of pinmux groups. The list of all available groups
|
|
depends on the SoC and can be found in driver sources.
|
|
- function: the name of a function to activate for the specified set
|
|
of groups. The list of all available functions depends on the SoC
|
|
and can be found in driver sources.
|
|
|
|
Required properties for configuration nodes:
|
|
- pins: a list of pin names
|
|
|
|
Configuration nodes support the generic properties "bias-disable",
|
|
"bias-pull-up" and "bias-pull-down", described in file
|
|
pinctrl-bindings.txt
|
|
|
|
=== Example ===
|
|
|
|
pinctrl: pinctrl@c1109880 {
|
|
compatible = "amlogic,meson8-pinctrl";
|
|
reg = <0xc1109880 0x10>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
gpio: banks@c11080b0 {
|
|
reg = <0xc11080b0 0x28>,
|
|
<0xc11080e8 0x18>,
|
|
<0xc1108120 0x18>,
|
|
<0xc1108030 0x30>;
|
|
reg-names = "mux", "pull", "pull-enable", "gpio";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
|
|
gpio_ao: ao-bank@c1108030 {
|
|
reg = <0xc8100014 0x4>,
|
|
<0xc810002c 0x4>,
|
|
<0xc8100024 0x8>;
|
|
reg-names = "mux", "pull", "gpio";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
|
|
nand {
|
|
mux {
|
|
groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
|
|
"nand_io_rb0", "nand_ale", "nand_cle",
|
|
"nand_wen_clk", "nand_ren_clk", "nand_dqs",
|
|
"nand_ce2", "nand_ce3";
|
|
function = "nand";
|
|
};
|
|
};
|
|
|
|
uart_ao_a {
|
|
mux {
|
|
groups = "uart_tx_ao_a", "uart_rx_ao_a",
|
|
"uart_cts_ao_a", "uart_rts_ao_a";
|
|
function = "uart_ao";
|
|
};
|
|
|
|
conf {
|
|
pins = "GPIOAO_0", "GPIOAO_1",
|
|
"GPIOAO_2", "GPIOAO_3";
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|