d9909ebe65
Device drivers should not access MMIO registers through hardcoded platform specific address constants. Instead, we can pass the MMIO token to the spear clock driver in the initialization routine to contain that knowledge in the platform code itself. Ideally, the clock driver would use of_iomap() or similar to get the address, and that can be used later, but for now, this is the minimal change. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
116 lines
3.1 KiB
C
116 lines
3.1 KiB
C
/*
|
|
* arch/arm/mach-spear3xx/spear3xx.c
|
|
*
|
|
* SPEAr3XX machines common source file
|
|
*
|
|
* Copyright (C) 2009-2012 ST Microelectronics
|
|
* Viresh Kumar <viresh.linux@gmail.com>
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without any
|
|
* warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
#define pr_fmt(fmt) "SPEAr3xx: " fmt
|
|
|
|
#include <linux/amba/pl022.h>
|
|
#include <linux/amba/pl080.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/io.h>
|
|
#include <asm/mach/map.h>
|
|
#include "pl080.h"
|
|
#include "generic.h"
|
|
#include <mach/spear.h>
|
|
#include <mach/misc_regs.h>
|
|
|
|
/* ssp device registration */
|
|
struct pl022_ssp_controller pl022_plat_data = {
|
|
.bus_id = 0,
|
|
.enable_dma = 1,
|
|
.dma_filter = pl08x_filter_id,
|
|
.dma_tx_param = "ssp0_tx",
|
|
.dma_rx_param = "ssp0_rx",
|
|
/*
|
|
* This is number of spi devices that can be connected to spi. There are
|
|
* two type of chipselects on which slave devices can work. One is chip
|
|
* select provided by spi masters other is controlled through external
|
|
* gpio's. We can't use chipselect provided from spi master (because as
|
|
* soon as FIFO becomes empty, CS is disabled and transfer ends). So
|
|
* this number now depends on number of gpios available for spi. each
|
|
* slave on each master requires a separate gpio pin.
|
|
*/
|
|
.num_chipselect = 2,
|
|
};
|
|
|
|
/* dmac device registration */
|
|
struct pl08x_platform_data pl080_plat_data = {
|
|
.memcpy_channel = {
|
|
.bus_id = "memcpy",
|
|
.cctl_memcpy =
|
|
(PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
|
|
PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
|
|
PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
|
|
PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
|
|
PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
|
|
PL080_CONTROL_PROT_SYS),
|
|
},
|
|
.lli_buses = PL08X_AHB1,
|
|
.mem_buses = PL08X_AHB1,
|
|
.get_signal = pl080_get_signal,
|
|
.put_signal = pl080_put_signal,
|
|
};
|
|
|
|
/*
|
|
* Following will create 16MB static virtual/physical mappings
|
|
* PHYSICAL VIRTUAL
|
|
* 0xD0000000 0xFD000000
|
|
* 0xFC000000 0xFC000000
|
|
*/
|
|
struct map_desc spear3xx_io_desc[] __initdata = {
|
|
{
|
|
.virtual = (unsigned long)VA_SPEAR_ICM1_2_BASE,
|
|
.pfn = __phys_to_pfn(SPEAR_ICM1_2_BASE),
|
|
.length = SZ_16M,
|
|
.type = MT_DEVICE
|
|
}, {
|
|
.virtual = (unsigned long)VA_SPEAR_ICM3_SMI_CTRL_BASE,
|
|
.pfn = __phys_to_pfn(SPEAR_ICM3_SMI_CTRL_BASE),
|
|
.length = SZ_16M,
|
|
.type = MT_DEVICE
|
|
},
|
|
};
|
|
|
|
/* This will create static memory mapping for selected devices */
|
|
void __init spear3xx_map_io(void)
|
|
{
|
|
iotable_init(spear3xx_io_desc, ARRAY_SIZE(spear3xx_io_desc));
|
|
}
|
|
|
|
void __init spear3xx_timer_init(void)
|
|
{
|
|
char pclk_name[] = "pll3_clk";
|
|
struct clk *gpt_clk, *pclk;
|
|
|
|
spear3xx_clk_init(MISC_BASE, VA_SPEAR320_SOC_CONFIG_BASE);
|
|
|
|
/* get the system timer clock */
|
|
gpt_clk = clk_get_sys("gpt0", NULL);
|
|
if (IS_ERR(gpt_clk)) {
|
|
pr_err("%s:couldn't get clk for gpt\n", __func__);
|
|
BUG();
|
|
}
|
|
|
|
/* get the suitable parent clock for timer*/
|
|
pclk = clk_get(NULL, pclk_name);
|
|
if (IS_ERR(pclk)) {
|
|
pr_err("%s:couldn't get %s as parent for gpt\n",
|
|
__func__, pclk_name);
|
|
BUG();
|
|
}
|
|
|
|
clk_set_parent(gpt_clk, pclk);
|
|
clk_put(gpt_clk);
|
|
clk_put(pclk);
|
|
|
|
spear_setup_of_timer();
|
|
}
|