268a03a42d
There is no way to interact with a physical PCI slot without sysfs, so encode the dependency and prevent this build error: drivers/pci/slot.c: In function 'pci_hp_create_module_link': drivers/pci/slot.c:327: error: 'module_kset' undeclared This patch _should_ make pci-sysfs.o depend on CONFIG_SYSFS too, but we cannot (yet) because the PCI core merrily assumes the existence of sysfs: drivers/built-in.o: In function `pci_bus_add_device': drivers/pci/bus.c:89: undefined reference to `pci_create_sysfs_dev_files' drivers/built-in.o: In function `pci_stop_dev': drivers/pci/remove.c:24: undefined reference to `pci_remove_sysfs_dev_files' So do the minimal bit for now and figure out how to untangle it later. Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fix-suggested-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
63 lines
1.5 KiB
Makefile
63 lines
1.5 KiB
Makefile
#
|
|
# Makefile for the PCI bus specific drivers.
|
|
#
|
|
|
|
obj-y += access.o bus.o probe.o remove.o pci.o quirks.o \
|
|
pci-driver.o search.o pci-sysfs.o rom.o setup-res.o \
|
|
irq.o
|
|
obj-$(CONFIG_PROC_FS) += proc.o
|
|
obj-$(CONFIG_SYSFS) += slot.o
|
|
|
|
# Build PCI Express stuff if needed
|
|
obj-$(CONFIG_PCIEPORTBUS) += pcie/
|
|
|
|
obj-$(CONFIG_HOTPLUG) += hotplug.o
|
|
|
|
# Build the PCI Hotplug drivers if we were asked to
|
|
obj-$(CONFIG_HOTPLUG_PCI) += hotplug/
|
|
ifdef CONFIG_HOTPLUG_PCI
|
|
obj-y += hotplug-pci.o
|
|
endif
|
|
|
|
# Build the PCI MSI interrupt support
|
|
obj-$(CONFIG_PCI_MSI) += msi.o
|
|
|
|
# Build the Hypertransport interrupt support
|
|
obj-$(CONFIG_HT_IRQ) += htirq.o
|
|
|
|
# Build Intel IOMMU support
|
|
obj-$(CONFIG_DMAR) += dmar.o iova.o intel-iommu.o
|
|
|
|
obj-$(CONFIG_INTR_REMAP) += dmar.o intr_remapping.o
|
|
|
|
obj-$(CONFIG_PCI_IOV) += iov.o
|
|
|
|
#
|
|
# Some architectures use the generic PCI setup functions
|
|
#
|
|
obj-$(CONFIG_X86) += setup-bus.o
|
|
obj-$(CONFIG_ALPHA) += setup-bus.o setup-irq.o
|
|
obj-$(CONFIG_ARM) += setup-bus.o setup-irq.o
|
|
obj-$(CONFIG_PARISC) += setup-bus.o
|
|
obj-$(CONFIG_SUPERH) += setup-bus.o setup-irq.o
|
|
obj-$(CONFIG_PPC32) += setup-irq.o
|
|
obj-$(CONFIG_PPC) += setup-bus.o
|
|
obj-$(CONFIG_MIPS) += setup-bus.o setup-irq.o
|
|
obj-$(CONFIG_X86_VISWS) += setup-irq.o
|
|
obj-$(CONFIG_MN10300) += setup-bus.o
|
|
|
|
#
|
|
# ACPI Related PCI FW Functions
|
|
#
|
|
obj-$(CONFIG_ACPI) += pci-acpi.o
|
|
|
|
# Cardbus & CompactPCI use setup-bus
|
|
obj-$(CONFIG_HOTPLUG) += setup-bus.o
|
|
|
|
obj-$(CONFIG_PCI_SYSCALL) += syscall.o
|
|
|
|
obj-$(CONFIG_PCI_STUB) += pci-stub.o
|
|
|
|
ifeq ($(CONFIG_PCI_DEBUG),y)
|
|
EXTRA_CFLAGS += -DDEBUG
|
|
endif
|