e150d6e725
The ATSTK1006 is basically an upgraded version of ATSTK1002 with 128 MiB SDRAM and 256 MiB NAND flash on board. Otherwise, the board is very similar to the ATSTK1002, so it uses the same board support file. Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
109 lines
2.7 KiB
Text
109 lines
2.7 KiB
Text
# STK1000 customization
|
|
|
|
if BOARD_ATSTK1000
|
|
|
|
choice
|
|
prompt "ATSTK1000 CPU daughterboard type"
|
|
default BOARD_ATSTK1002
|
|
|
|
config BOARD_ATSTK1002
|
|
bool "ATSTK1002"
|
|
select CPU_AT32AP7000
|
|
|
|
config BOARD_ATSTK1003
|
|
bool "ATSTK1003"
|
|
select CPU_AT32AP7001
|
|
|
|
config BOARD_ATSTK1004
|
|
bool "ATSTK1004"
|
|
select CPU_AT32AP7002
|
|
|
|
config BOARD_ATSTK1006
|
|
bool "ATSTK1006"
|
|
select CPU_AT32AP7000
|
|
|
|
endchoice
|
|
|
|
|
|
config BOARD_ATSTK100X_CUSTOM
|
|
bool "Non-default STK1002/STK1003/STK1004 jumper settings"
|
|
help
|
|
You will normally leave the jumpers on the CPU card at their
|
|
default settings. If you need to use certain peripherals,
|
|
you will need to change some of those jumpers.
|
|
|
|
if BOARD_ATSTK100X_CUSTOM
|
|
|
|
config BOARD_ATSTK100X_SW1_CUSTOM
|
|
bool "SW1: use SSC1 (not SPI0)"
|
|
help
|
|
This also prevents using the external DAC as an audio interface,
|
|
and means you can't initialize the on-board QVGA display.
|
|
|
|
config BOARD_ATSTK100X_SW2_CUSTOM
|
|
bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
|
|
help
|
|
If you change this you'll want an updated boot loader putting
|
|
the console on UART-C not UART-A.
|
|
|
|
config BOARD_ATSTK100X_SW3_CUSTOM
|
|
bool "SW3: use TIMER1 (not SSC0 and GCLK)"
|
|
help
|
|
This also prevents using the external DAC as an audio interface.
|
|
|
|
config BOARD_ATSTK100X_SW4_CUSTOM
|
|
bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
|
|
help
|
|
To use the camera interface you'll need a custom card (on the
|
|
PCI-format connector) connect a video sensor.
|
|
|
|
config BOARD_ATSTK1002_SW5_CUSTOM
|
|
bool "SW5: use MACB1 (not LCDC)"
|
|
depends on BOARD_ATSTK1002
|
|
|
|
config BOARD_ATSTK1002_SW6_CUSTOM
|
|
bool "SW6: more GPIOs (not MACB0)"
|
|
depends on BOARD_ATSTK1002
|
|
|
|
endif # custom
|
|
|
|
config BOARD_ATSTK100X_SPI1
|
|
bool "Configure SPI1 controller"
|
|
depends on !BOARD_ATSTK100X_SW4_CUSTOM
|
|
help
|
|
All the signals for the second SPI controller are available on
|
|
GPIO lines and accessed through the J1 jumper block. Say "y"
|
|
here to configure that SPI controller.
|
|
|
|
config BOARD_ATSTK1000_J2_LED
|
|
bool
|
|
default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
|
|
|
|
choice
|
|
prompt "LEDs connected to J2:"
|
|
depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM
|
|
optional
|
|
help
|
|
Select this if you have jumpered the J2 jumper block to the
|
|
LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
|
|
IDC cable. A default "heartbeat" trigger is provided, but
|
|
you can of course override this.
|
|
|
|
config BOARD_ATSTK1000_J2_LED8
|
|
bool "LED0..LED7"
|
|
help
|
|
Select this if J2 is jumpered to LED0..LED7 amber leds.
|
|
|
|
config BOARD_ATSTK1000_J2_RGB
|
|
bool "RGB leds"
|
|
help
|
|
Select this if J2 is jumpered to the RGB leds.
|
|
|
|
endchoice
|
|
|
|
config BOARD_ATSTK1000_EXTDAC
|
|
bool
|
|
depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM
|
|
default y
|
|
|
|
endif # stk 1000
|